軋裂 的英文怎麼說

中文拼音 [yàliè]
軋裂 英文
roll burst
  • 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
  • 裂 : 裂動詞[方言] （東西的兩部分向兩旁分開） open
  1. The results show that " the frame - pack rolling " technology can increase the densify, avoid cracking during rolling, and effectively improve the deformability and mechanical properties of the spray deposited porous aluminum alloy sheets

    結果表明：外框限制軋制工藝提高了噴射沉積多孔材料的緻密度，避免了軋制過程中裂紋的形成，有效地改善了噴射沉積板坯的軋制性能及材料的力學性能。
  2. To evaluate fracture instability, the total sum of stresses due to residual welding or rolling stresses, dead load, and live loads must be considered.

    計算斷裂失穩性時，必須考慮焊接或軋制殘余應力，恆載應力和活載應力之總和。
  3. And it investigates the appearance condition ( including joint, crack, eroding, corrosion, braking pole device rupture, crane - girder ' s gnawing railway and so on ) of the whole crane - girder system on the spot, at the same time, it also actually examines the stress of the beam, chemical ingredient, distortion and railway excursion, etc. through sampling, and based on the actually examined results, it checks and calculates the carrying capacity of crane - girder system. then, based on the investigating on the spot and the calculated result, it discusses the mechanism of fatigue failure of the upper part of welded steel crane - girder, analyses the reason of steel crane - girder in the high - frequency emerging the fatigue crack, institutes the strengthened method of damaged steel crane - girder of accurate packing up workshop of the primary mill plant. finally, it presents some advice and suggestions for the repairing and strengthening method of fatigue crack of upper part of steel crane - girder in the high - frequency

    針對包鋼初軋廠精整車間鋼吊車樑上部區域出現裂縫這一問題，本文首先綜述了國內外關于焊接鋼吊車樑上部區域疲勞裂縫的研究現狀；其次對整個吊車梁系統的外觀情況（包括連接、裂縫、腐蝕、銹蝕、制動桿件斷裂、吊車啃軌等）進行了現場調查，抽樣實測了梁的應力、化學成分、變形及軌道偏移等，根據實測結果，對吊車梁系統的承載能力進行了驗算；然後，根據現場調查及計算結果，探討了焊接鋼吊車樑上部區域疲勞破壞的機理，分析了重級工作制鋼吊車梁出現疲勞裂縫的原因，制定了初軋廠精整車間破損鋼吊車梁的加固方案；最後就重級工作制鋼吊車樑上部區域出現疲勞裂縫的修復與加固方案提出了一些意見和建議。
  4. The grainy sand had gone from under his feet. his boots trod again a damp crackling mast, razorshells, squeaking pebbles, that on the unnumbered pebbles beats, wood sieved by the shipworm, lost armada. unwholesome sandflats waited to suck his treading soles, breathing upward sewage breath

    他的靴子重新踩在咯吱一聲就裂開來的濕桅桿上，還踩著了竹蟶，發出軋轢聲的卵石，被浪潮沖撞著的無數石子62 ，以及被船蛆蛀得滿是窟窿的木料，潰敗了的無敵艦隊63 。
  5. Wear resistant layer of cylinder and double - layer liner in catalyst creaking apparatus ( without or with tortoiseshell net can be used ), inner liner of carbon monoxide exhaust - heat boiler, pouring at site for furnace roof with high temperature of heating furnace of steel rolling, different forging furnace, resistance furnace, the prefabricated parts can also be made

    催化裂化裝置中的筒體耐磨層及雙層襯里， （無龜甲網和有龜甲網均可採用）及一氧化碳余熱鍋爐的內襯，也適用於軋鋼加熱爐、各種煅造爐、電阻爐的爐頂、爐墻、爐底高溫部位的現場澆注，可製成預制構件。
  6. It can also create micro cracked edges if the speed is forced to remain higher, which can create quality concerns downstream during following passes

    如果強制保持較高軋制速度，則也會導致微裂邊，從而對后道次加工過程中的下游工序造成質量問題。
  7. Analysis of tendency of ductile fracture at corner of workpiece during grooveless rolling

    無槽軋制軋件角部的韌性斷裂趨勢分析
  8. The reason that the internal defects little occur at the center points and fissure takes an annular form during three - roll rolling was expounded based on the state of stress and strain at the center of rolled pieces

    根據軋件內部的應力應變狀態，闡述了三輥軋制軋件中心點缺陷產生可能性較小和斷裂呈環向裂紋的原因。
  9. It ' s the advantage of jmfc to apply the centrifugal casting technology to the small size of compound rolls, which characteristics are as follows : combining high hardness, anti - wear, impact and breakage resistance : spun cast the shell by proper charging of alloys and use high strength and impact ductility material as core

    將離心澆鑄工藝用於小型復合軋輥的製造，是金環廠的優勢，採用該工藝的軋輥具有以下特點：兼得高硬度耐磨損與抗沖擊抗斷裂性能：按耐磨性和硬度要求，將合金科學配比，溶解澆鑄成輥身的工作層，再採用高強度抗沖擊的材料澆鑄輥頸和輥芯，冶金結合，兩者兼得。
  10. The company owns advanced middle frequency furnace, compound centrifugal casting machine, precise and complete metal cutting equipment and advanced and modern quality measurement and control means

    本公司擁有先進的中頻電爐、復合式離心澆鑄和精密齊全的金屬切削設備以及先進的現代化質量測控手段，生產的合金軋輥具有輥面度高、強度大、耐磨性能好、耐熱裂、抗剝落等特點。
  11. On the basis of the search of production locale, recently, the accidents of roller fraction often happen in steel rolling middle armor - plated plant, which not only brings large economic loss to itself, but also brings large influence to production. and its general loss can be much larger

    根據生產現場調研，近年來，軋鋼中板廠的中板軋機斷輥事故時有發生，不但軋輥自身斷裂會造成重大經濟損失，還嚴重影響生產，其綜合損失會更大。
  12. The reason analysis for the bloom cracks of sus304hc stainless steel with cu content

    含銅不銹鋼初軋坯開裂原因分析
  13. Measures to prevent cracking of top roll neck of chilled alloyed cast iron rolls

    防止合金冷硬鑄鐵軋輥上輥頸裂紋的措施
  14. Spray deposited porous aluminum alloy sheets easily have surface and edge crack when they are directly rolled due to the porosity and metallurgical bond

    摘要噴射沉積多孔鋁合金板坯由於有孔洞且缺乏良好的冶金結合，直接軋制時易出現板坯表面裂紋及邊裂。
  15. The grain - boundary cracks are found when the deformation of the strip is greater than a value, and these cracks will become marco cracks with the increase of the deformation

    變形量過大時，冷軋薄帶內部出現微觀晶界裂紋，並隨著變形量的增加最終發展成宏觀裂紋。
  16. Analysis and countermeasure for fracture forms of rolls in hot rolling section steel

    熱軋型鋼軋輥的斷裂行為分析及對策
  17. In this paper, the internal transverse cracks of continuous casting slabs of a niobium - bearing peritectic grade of steel are investigated using electron probe microanalyser and optical microscope

    摘要連鑄坯厚度中心存在的內裂紋在後續的軋制過程中軋不合而對產品的質量帶來重大的影響。
  18. Abstract : the structure, composition analysis and mechanical test of q235 hot - rolled strip showed that main season of fracture during forming and welding is high nitrogen, oxygen and inclusion content

    文摘: q235鋼熱軋卷板在沖壓和焊接成形時出現開裂，對其進行化學分析、宏觀和微觀組織觀察及力學性能測試，結果表明：氮、氧及夾雜物的含量高是該鋼沖壓性和可焊性差的主要原因。
  19. Based on the experimental study and theoretical analysis about the concrete members reinforced with cold - rolled ribbed bars subjected to bending, the correction formula about calculating deformation and crack width have been presented, and the calculated results relatively conform to the experimental results. the research results will be helpful to the development and application of the cold - rolled ribbed bars. 3tabs., 6refs

    在試驗研究的基礎上，分析了冷軋帶肋鋼筋受彎構件的裂縫寬度和撓度變形規律，提出了其裂縫寬度和撓度驗算修正公式，修正值與實測值吻合較好，有利於冷軋帶肋鋼筋的進一步推廣應用.表3 ，參6
  20. Ifs a kind of phemonemon of anisotropic material to crack hot rolled drawing sheet

    摘要熱軋沖壓板開裂現象是一種板材料力學性能各向異性的表現。
分享友人
分享到 Line

分享到臉書