軸向施加力 的英文怎麼說

中文拼音 [zhóuxiàngshījiālì]
軸向施加力 英文
axial a lication of force
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 施 : Ⅰ動詞1 （實行; 施展） execute; carry out 2 （給予） exert; impose 3 （施捨） give; hand out; best...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 施加 : exert; bring to bear on; impose
  1. This method can be used for pellets with flat faces with crushing along the axis.

    這種方法可以用於具有平面的片劑，沿著軸向施加壓力。
  2. This research was also supposed to provide a valuable reference for the construction of 500kv eastern hangzhou transformer substation project. to guarantee the rationality of the torsion and bending load application, a set of experimental equipments was transformed from a traditional one by exerting tangential force on the brim of the fan board and conducting broad - billed roller application. in the actually fulfilled experiments on the capabilities of the members under different ratios of torsion and bending, the equipments proved to be well qualified in load applying to large - tonnage members

    試驗中，為保證扭轉及彎矩荷載施加的合理性，在浙江大學工程結構試驗室原有的加載設備的基礎上，分別採用在扇形板邊緣施加切向力和寬軸承滾軸加載的方法，改造並調試出一套可專門用於大噸位構件施加扭轉荷載及組合作用的試驗設備，並利用這套設備進行了離心鋼管混凝土構件在不同彎扭比的組合作用下的試驗研究。
  3. In the condition of the different confining stress and the temperature of 8. 8 ?, dynamic strain of the asphalt concrete is very little within 100 vibration times under rather big dynamic stress, the total axial strain is only about 1 % ~ 2 % within 3000 ~ 5000 vibration times

    在不同圍壓和8 . 8條件下，對瀝青混凝土施加較大的動應力，在100振次以內所產生的動應變是很小的，即使施加3000 5000振次，軸向總應變也僅為1 2左右。
  4. Axial application of force

    軸向施加力
  5. According to the documentation collected from domestic and abroad wang wei dong who works in huadong architect and structure institute utilizes the similar work property between the underground continuous wall and pile subjected the vertical loads, and introduces poulos method of elasticity and plastic which applies to pile foundation into the calculation for subsidence of underground continuous wall. pujialiu and yu yuzhou from water and electronic engineering of qinghua university, according to the result of three axes, define the concrete parameter utilize the model of non - linear e - b combined with the design cross section of dam in xiaolangdi, yellow river accept the total stress programme of thepd dam, and we analyze the stress and displacement of plastic concrete diaphragm wall by finite element method in comparison with the result of common concrete one. at same time, we consider the effect of the character of plastic concrete diaphragm wall which is composed of different gradients and adopting the level of stress and pulling stress infers whether the plastic concrete diaphragm wall is safe or not

    地下連續墻是一種歷史較短的施工方法，目前，砼防滲墻的設計還是以傳統的設計方法為主，根據查找國內外文獻資料，華東建築設計院王衛東利用地下連續墻與樁在豎向荷載作用下的工作性能有相似性，將適用於樁基的poulos彈性理論引入對地下連續墻的沉降計算中；清華大學水利水電工程系濮家騮、于玉貞根據三軸試驗結果確定混凝土的參數，利用非線性e - b模型，結合黃河小浪底土石壩設計剖面，採用thepd土石壩總應力程序，對深覆蓋層塑性混凝土防滲墻的應力、位移進行有限元分析，並與普通混凝土防滲墻計算結果加以對比，同時分析了不同配比塑性混凝土特性的影響，並採用應力水平和拉應力數值來判斷塑性混凝土防滲墻的安全程度。
  6. In the test, static - dynamic method is used to measure the stiffness, the eight stiffness coefficients of the radial part and the two stiffness coefficients of the thrust part can be obtained though loading slowly to the testing bearing which is in a equilibrium position

    首先，對處于平衡位置的測試軸承分別沿水平方向、鉛垂方向及軸向緩慢施加載荷，根據靜動法原理求得各個轉速下測試軸承徑向部分內、外膜8個剛度系數以及推力部分內、外膜2個剛度系數。
  7. Establish geometry model of hyperboloid clutch with rollers with differential geometry. we know that the line of tangent is beeline and validate it with matlab. in the base of above research, establish movement model of hyperboloid clutch with rollers and find the relation between force of outer race and moment of inner race

    在上述研究的基礎上利用運動轉化原理建立了內外環與滾柱之間的運動模型，並利用微分幾何的相關知識通過對施加在外環上的主動軸向力的分解及合成，求的其在內環上所產生的力學反應，建立雙曲面滾柱加載器力學模型。
  8. By the net - shape forming technology, metal sheet is used as a blank, the cylindrical cup is produced through blanking, deep drawing, and etc, and then the cup is clamped to a mandrel rotated together with the main spindle, the pulley is finally produced by several different spinning rollers, which apply the radial spinning forces to the cup in different positions

    鈑制帶輪是以金屬板料為毛坯，經過落料、拉深等沖壓工序製成圓筒狀，然後將其裝夾在帶有頂壓座的芯模上，使其隨主軸一起旋轉，通過若干不同齒形的旋壓成形輪分別沿徑向施加壓力而成形。
分享友人
分享到 Line

分享到臉書