載止電路 的英文怎麼說

中文拼音 [zǎizhǐdiànlù]
載止電路 英文
cutoff circuit
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 止 : Ⅰ動詞1. （停止; 攔阻） stop; cut out 2. （截止） close; end Ⅱ副詞（僅; 只） only; just Ⅲ名詞（姓氏） a surname
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 路 : 1 （道路） road; way; path 2 （路程） journey; distance 3 （途徑; 門路） way; means 4 （條理） se...
  • 電路 : [訊] circuit （ckt）; electric circuit; electrocircuit電路板 circuit board; 電路保持 guard of a c...
  1. Assuming the loop is known to be only a single straight segment of 26awg cable, there is no additive loop or afe noise, and the remote - end is terminated by a high - impedance load for all frequencies, figure 5 shows the resulting selt performance

    假定已知環路只有一個單個的直段26awg電纜，沒有附加的環路或者afe噪聲，對所有的頻率遠端通過一個高祖抗負載終止，圖5給出了selt的性能結果。
  2. Continuous adjustable current 0 ~ 1a could avoid shock by high current. technician could estimate safety current data after testing normal current as referral

    具連續可調恆流輸出0 ~ 1a ，根據被測電子線路的正常耗用電流值參考，估算預設安全的恆流值，防止大電流對負載的沖擊。
  3. Abstract : the rechargeble batteries are used for backup power internal electrically equipments and instruments. but batteries lifetime usually is shorten by overwork and then malfunctions of equipment are induced. to avoid the complexion described above, the protection circuit against overwork is designed. it is based upon the voltage comparator and regulator. it will light up a red led when the volume of the batteries discharged close upon 50 % ; it will switch off the load automatically when it discharged closing to 80 % of their energy capacity, thus overwork of batteries can be avoided and lifetime may be extended

    文摘:用蓄電池做后備電源的系統（或設備） ，常因過放電導致電池提前報廢而造成設備故障.根據電池電壓隨容量變化的規律，利用電壓比較器和電壓基準源設計製作了電池放電保護電路，當電池放電量接近容量的50 %時，啟動預警信號；當電池放電量達到容量的80 %時，電路自動切斷負載，防止電池過度放電，延長電池壽命，保證系統（或設備）在供電恢復正常后能正常運行
  4. To prevent pumping system stopping working, working without efficiency and being destroyed, so it is very important to monitor oil - well. the thesis dissertates the process of developing displacement - load sensor which collects displacement data and load data to form the indicator diagrams, researches the means based on rbf neural network of recognizing fault types, designs parts of hardware and software of the mainframe of the oil - well monitor and control system, and debugs the entire oil - well monitor and control system

    為了防止抽油機故障停機、無油空抽、不法分子的蓄意破壞等情況的發生，因此對油井工況進行實時監控顯得尤為重要。本文論述了採集用於形成油井示功圖的位移和載荷數據的傳感器的研製，包括硬體電路和軟體的設計，對基於rbf神經網路的油井工況模式識別方法進行了研究，對監控系統主機的部分硬體電路及相應的軟體進行了設計，並對整個油井監控系統進行了聯調和測試。
分享友人
分享到 Line

分享到臉書