載錐體 的英文怎麼說

中文拼音 [zǎizhuītǐ]
載錐體 英文
truncated cone
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 錐 : Ⅰ名詞1. （錐子） awl2. （似錐物） awl-shaped things 3. （錐體） cone Ⅱ動詞（鉆） drill; bore
  • 體 : 體構詞成分。
  1. The design calculation of the heat carrier pyrogenation stove in rotating cone reactor device of biomass pyrolysis

    轉錐式生物質熱解裝置中熱載體加熱爐設計計算
  2. The shear strength increases by 3 - 6 times after improvement through vane shear test and the resistance increases largely through cpt. the soft foundation treated by vacuum combined with surcharge preloading is very effective. second, the mechanism and some problems of vacuum combined with surcharge preloading were analyzed

    通過十字板剪切試驗與靜力觸探試驗，加固後土體的抗剪強度一般可提高3 6倍，錐尖阻力與側壁阻力也有大幅增長，說明真空聯合堆載預壓加固軟土地基的效果顯著。
  3. For example, the vehicle ' s angular and linear vibrations will result in the coning error, the sculling error and the scrolling error, so perfect algorithms should be designed to reduce the errors

    有些誤差，如運載體的角振動和線振動所引起的圓錐誤差、劃船誤差及渦卷誤差，則必須通過設計合適的演算法來解決。
  4. In this thesis the problems relative with safe reliability of parachute recovery system of manned spacecraft are commenced, the coning motion of the systems in steady decent are studied emphatically ; in view of multibody dynamics, two different dynamic modeling principles and methods of parachute systems have been discussed, and their dynamic characteristics are analytically compared

    本文從載人飛船回收系統安全可靠性緊密相關的問題著手，重點研究了降落傘系統在穩定下降過程中的錐擺現象;並且從多體系統動力學的角度出發，討論了物傘系統的兩種不同動力學建模理論和方法，並對它們的動力學特性進行了分析比較。
  5. The numerical results show that an appropriate applied voltage potential across the piezoelectric shell has the effect of suppressing the reflected pressure from the sphere shell in a cone fluid field, and able to completely cancel the reflections at any chosen field points

    研究表明，在壓電中加載適當的電壓可以在一個圓錐形的流體區域內有效地減小殼體對于外來聲波的反射，並且有可能完全消除任意選定空間點上的反射。
  6. A mathematical model of flows in the substrate was established using the equivalent continuum approach, and multi - dimensional numerical simulation of the steady flows in the catalytic converters was performed. simulation results show that the separation and vortex, which cause the pressure loss and the velocity non - uniformity at the front of the first substrate, are generated near the wall of the conical pipe. in addition, the larger the inlet cones angle the more the pressure loss and maldistribution in converters, however, when the angle enlarges enough the pressure loss would be decrease

    結果顯示氣流在擴張圓錐管壁附近出現分離產生較強的擾動，造成局部流動損失和載體前氣流速度沿徑向分佈不均勻；入口擴張管結構對催化器的流動特性有很大影響，但並非擴張角越大，催化器流速武漢理工大學碩士學位論文分佈的不均勻性和壓力損失也增大，而是存在著一個最佳角度，但當擴張角增大到一定程度以後，擴張角對流速分佈和壓力損失的影響變小。
  7. Abstract : on the base of the analysis of kinematics and dynamics f or i ntroduced some types of cone crushers, this paper constructs the dynamics models with the fin ite element method on the main components of the cone crushers, such as main shaf t, moving cone and offcentering axial bushing. according to the characters of the load, the paper simplifies and counts the external loads. then using the software of ansys and employing the elements of high accurate three dimension block, the paper analyzes the strength and rigidity of the finite element method and a ttains valuable results

    文摘:在對引進的某型圓錐破碎機的運動學及動力學分析的基礎上，建立了該破碎機主要部件主軸、動錐及偏心軸套的有限元分析模型.根據載荷特點，簡化並計算了外載荷.應用ansys軟體，選用精度較高的三維塊單元，對其進行了有限元分析，得出了具有參考價值的計算結果
  8. The green ' s function of infinite and half - infinite space, the solutions of a cone under concentrated loads at its apex, and rotating circular and annular plate of magnetoelectroelastic medium are obtained by use of these solutions and given boundary conditions

    在此基礎上，由平衡問題的一般解和邊界條件，得到了磁電彈性介質無限空間和半空間的green函數解、圓錐體頂端受集中荷載作用的解析解、旋轉圓盤和圓環的三維解析解。
  9. 4. conclude and verify detailedly attitude algorithm and conical scan control algorithm in process of initial alignment. on the base of static initial alignment technology, reach the dynamic initial alignment technology used on moving carrier

    四、對在初始對準中採用的姿態解算和圓錐掃描控制演算法進行了詳細的理論推導和模擬驗證，然後在靜態初始對準的基礎上，引出了用於載體移動過程中的動態初始對準。
  10. 4 ) combining the local synthesis method for the machine - tool setting parameters, tca and ltca, and the numerical simulation of stress procedure constructs the optimal design circle with feedback. the developed software system provides an efficient design tool for the spiral bevel gears with excellent transmission behavior, high strength and lower noise

    4 ）結合加工參數設計的局部綜合法、幾何接觸分析（ tca ） 、承載接觸分析（ ltca ）及應力過程數值模擬，構成了具有反饋的閉環優化設計迴路，並形成了相應的軟體系統，為設計嚙合性能良好、高強度、低噪聲的弧齒錐齒輪傳動提供了有效的工具。
分享友人
分享到 Line

分享到臉書