輥壓成形 的英文怎麼說

中文拼音 [gǔnyāchéngxíng]
輥壓成形 英文
gauge forming
  • 輥 : 名詞[機械工程] （能滾動的圓柱形機件） roller
  • 壓 : 壓構詞成分。
  • 成 : Ⅰ動詞1 （完成; 成功） accomplish; succeed 2 （成為; 變為） become; turn into 3 （成全） help comp...
  1. Fem simulation of roll extrusion forming process of square section tube

    矩形管雙道次輥擠成型過程擠壓力公式的建立
  2. Through the simulation of the forming process, we can get the deformations, stress, strain, plastic flowing in sheets and the interface state under impact load and rolling load, the deformation of the sawtooth form and comparing to the initial state, the results above are expressed in computer animated way. and the effect of geometrical ( mainly different form, including 90 degree, isoceles triangle ， 75 degree, and 1. 5 high and wide ), material and technical parameters on the bond strength are analyzed, also including the comparison of different sawtooth form. the optimum parameters are got

    對雙金屬復合板成型過程進行模擬，從而得到在沖擊載荷和軋輥壓力作用下基板和覆板的應力、應變分佈和塑性流動變形規律，復合后的齒形的變形情況與初始齒形形成對比，以動畫的方式模擬成型過程，並分析了不同幾何參數（主要是不同的齒型，其中包括直角齒型、等腰齒型、 75度齒型、 1 . 5高寬齒型） 、材料參數、工藝參數對復合強度的影響，以及不同齒型的變形對比以及齒型對復合情況的影響，提出最優齒型、最優工藝參數，有效地指導了實驗。
  3. The configuration of conventional backup and work rolls for revamped 1700 tandem cold rolling mill at wisco was proved unreasonable by systematical test as the cause of work roll edges contact during thin strip rolling and unsatisfactory flatness of product

    摘要通過現場跟蹤測試和生產實踐發現武鋼1700冷連軋機組「酸軋聯機」改造工程中存在常規凸度輥形配置方案不合理，由此引起了薄規格軋制的工作輥「壓肩」現象和軋制過程欠穩定導致成品板形質量欠佳等問題。
  4. It ` s suitable for the bend and deformation of the metal plates and it can roll the round and arcshapes and the cone ones within its specified ranges. it has the function of prebending the plate at both ends. the two lower rollers are the driving ones and can make the horizontal movement ; and the upper is a driven one and can make the up and down movement. the moving manner includes the mechanical and industry, boilers, shipbuilding, metal structure, machine manufacture and other trades, especially for the roll the steel trunks with smaller diameter and longer length in power transmission and trandform and other trades

    該機適用於金屬板材的彎曲成型，可卷制圓形，弧形和一定范圍的錐形工作，並有板材端部預彎功能，本機型兩個下輥為主動輥並可水平移動，上輥為從動輥上下移動，移動形式有機械式和液壓式，傳動軸均採用萬向連軸器連接，它廣泛適應于石油化工鍋爐造船金屬結構及機械製造行業，特別適用於送變電行業等直徑較小長度較長鋼管桿的卷制
  5. Automatic fiber placement ( fp ) is a new manufacture technique to produce the affordable composite materials. in fp process fiber is placed on the surfaces of the model by the press roller to form composite structure with low manufacture cost, high efficiency and good quality

    自動鋪絲技術是一種新型復合材料低成本自動化製造技術，它是通過壓輥傳遞一定的正壓力將纖維鋪設在芯模曲面上形成復合材料殼體結構。
  6. The results indicate that the time of press influences sawtooth distortion greatly, but infects sawtooth less. root of the sawtooth made by the method of static simulating rolling have no changes hardly, and from the upper distance the changes became, then on the top the sawtooth curves to the opposite direction

    結果表明：壓制時間對齒形的變形影響較大，對齒型的影響很小；模擬軋輥壓制的鋸齒，根部一段幾乎沒有變化，是從一段距離開始變形，然後在頂端向相反的方向彎曲；壓製成型后，鋁板厚度的變化很小。
分享友人
分享到 Line

分享到臉書