輥軋板 的英文怎麼說

中文拼音 [gǔnyàbǎn]
輥軋板 英文
rolled sheet
  • 輥 : 名詞[機械工程] （能滾動的圓柱形機件） roller
  • 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  1. We have in - house rolling, forging and machining capability to manufacture all types of fishplates including plain, joggled, angle, and combination fishplate to various drawings for various rails

    我們有內部的軋輥，鍛造和機床加工這樣的技術，有能力去生產所有類型的魚尾板包括普通魚尾板，嚙合型魚尾板，角形魚尾板和組合型魚尾板根據各種各樣的圖紙為各種各樣的鐵路。
  2. The development of heavy plate mill and the common characteristics of the mill revamping were summarized, and the production technologies, such as control links of tmcp, appliction of edger mill and the processing of steckel mill for plate were introduced

    綜述了厚板軋機的發展及其技術改造的特點；介紹了厚板生產tmcp技術的控制環節，立輥軋機的應用以及卷軋中板的生產工藝特點。
  3. Fictious simulation of high - speed roll casting has been carried out on the basis of the fact. the results showed that roll casting speed increase with the decrease of the thickness of the strip, and the peak value of rolling pressure decrease with the increase of roll casting speed and thickness of strip or the increase of roll casting zone. the designed parameters of mechanical capabilities of the roll caster should be raised when rolling pressure increase with roller diameter increase

    研究結果表明，減薄鑄軋板坯厚度可提高鑄軋速度；隨著鑄軋速度降低、鑄軋區增大與鑄軋坯厚度減薄，軋制壓力峰值增大；隨著鑄軋輥徑增大，軋制壓力增大，因此鑄軋機力能設計參數也要相應增大。
  4. Responding to the call of industrial policy adjustment in our country, yaoyu special steel company has started replacing hot - rolling with cold - rolling in the production of electric steel since 2003. it entrusted xinye gaoke group to make design and build the production line of cold - rolled electric steel with annual output of 200 thousand tons. after three years of construction, it has achieved the successful trial production of 20 - roll mill and continuous annealing and coating machine imported from germany

    耀宇特鋼從2003年開始，響應國家產業政策調整的號召，開始電工鋼以冷代熱技改工程，委託新冶高科集團原冶金部鋼研院設計，進行年產20萬噸冷軋電工鋼生產線的建設，經過近三年的建設，目前從德國引進的20輥軋機及連續退火塗層機組均已試產成功，為提高產品的性能和質量，同時提升我國電工用薄鋼板的生產作出了卓越的貢獻。
  5. Our rubber roller products are complete in series and meet all the specifcation requirements. they are used in printing houses, paper mills, dye - works, textile mills, plastic processing works, steel rolling plants, timber ( plank ) processing works, office automation equipment, etc. gd xinli produces water rollers, uv rollers, rollers that can resist different kinds of chemical solvents, rollers that can resist acidalkaline, polishing rollers, polyurethane rollers, etc. the annual amount of production reaches 120 tons

    規格品種齊全，適用於印刷、造紙、印染、紡織、塑料加工、軋鋼、膠合板（木材加工）和辦公自動化設備等。例如水輥、 uv輥、耐各種化學溶劑膠輥、耐酸堿膠輥、磨光輥、聚氨酯膠輥等。年產量達120噸。
  6. Through the simulation of the forming process, we can get the deformations, stress, strain, plastic flowing in sheets and the interface state under impact load and rolling load, the deformation of the sawtooth form and comparing to the initial state, the results above are expressed in computer animated way. and the effect of geometrical ( mainly different form, including 90 degree, isoceles triangle ， 75 degree, and 1. 5 high and wide ), material and technical parameters on the bond strength are analyzed, also including the comparison of different sawtooth form. the optimum parameters are got

    對雙金屬復合板成型過程進行模擬，從而得到在沖擊載荷和軋輥壓力作用下基板和覆板的應力、應變分佈和塑性流動變形規律，復合后的齒形的變形情況與初始齒形形成對比，以動畫的方式模擬成型過程，並分析了不同幾何參數（主要是不同的齒型，其中包括直角齒型、等腰齒型、 75度齒型、 1 . 5高寬齒型） 、材料參數、工藝參數對復合強度的影響，以及不同齒型的變形對比以及齒型對復合情況的影響，提出最優齒型、最優工藝參數，有效地指導了實驗。
  7. The research of the influence of gap setting precision on finishing plate size precision shows that the sensibility of finishing size precision to gap setting precision of the first several passes is low

    摘要分析中厚板軋制過程不同道次輥縫設定精度對軋件終軋尺寸精度的影響，證明了軋件終軋尺寸精度對前面道次的輥縫設定精度不敏感。
  8. The practical application indicates that the new design not only reduces the convexity of the roll profile obviously, but also leads to homogeneous attrition of rolls and low roll wear

    生產實際應用表明，新設計的輥型不僅明顯降低了板凸度，同時使軋輥磨損均勻，輥耗量大大下降。
  9. The rolls wear characteristics and work roll wear pattern were analyzed theoretically and the quantitative analysis were made in shape control and effect factor in accordance with the rolling conditions

    從理論上分析了輥系在軋制中的磨損特性，工作輥磨損輥型的計算方法，根據實際軋制工況對其板形的調控、影響因素進行了定量分析。
  10. In order to make the camber design easier and keep contact pressure equal along rolls, we shall assume the pressure distribution to be quadratic along the width and the marginal deformation to be planar

    摘要為了使中厚板軋機輥型設計快捷且保持輥間各點接觸壓力相等，利用了壓力沿板寬方向呈二次分佈、板邊緣處變形為平面變形的計算處理，從而使輥型設計更為方便。
  11. The model considers not only the slab bounce on gauge and hardness, obverse and inverse bounce on width, and the rolling length constraint of the slabs with same width, but also the reasonable arranging of warm - up materials and staple materials

    該模型不僅考慮了軋制計劃中板坯在厚度和硬度上的跳躍、板坯寬度的正反跳以及相同寬度板坯連續軋制的長度約束，而且考慮了軋制計劃中燙輥材和主體材的合理安排。
  12. On the basis of the search of production locale, recently, the accidents of roller fraction often happen in steel rolling middle armor - plated plant, which not only brings large economic loss to itself, but also brings large influence to production. and its general loss can be much larger

    根據生產現場調研，近年來，軋鋼中板廠的中板軋機斷輥事故時有發生，不但軋輥自身斷裂會造成重大經濟損失，還嚴重影響生產，其綜合損失會更大。
  13. The configuration of conventional backup and work rolls for revamped 1700 tandem cold rolling mill at wisco was proved unreasonable by systematical test as the cause of work roll edges contact during thin strip rolling and unsatisfactory flatness of product

    摘要通過現場跟蹤測試和生產實踐發現武鋼1700冷連軋機組「酸軋聯機」改造工程中存在常規凸度輥形配置方案不合理，由此引起了薄規格軋制的工作輥「壓肩」現象和軋制過程欠穩定導致成品板形質量欠佳等問題。
  14. Influence of electric grid voltage fluctuation on main motor drive system for four - high medium plate mill and its solution are introduced

    摘要介紹了電網電壓波動對中板四輥軋機主電機傳動系統的影響和解決方法。
  15. According to recording data of higher level monitor and control system when main motor drive system for four - high medium plate mill is operated, and relation between armature voltage of dc electromotor and ac input voltage of inverter, trip cause of dc fast automatic switch was analyzed in detail, and specific countermeasure and measures are given

    根據中板四輥軋機主電機傳動系統運行時的上級監控系統記錄數據，以及直流電機電樞電壓與變流器交流側輸人電壓的關系，詳盡地分析了直流快速自動開關跳閘故障原因，並提出具體的對策及措施。
  16. Steel ' s surface damage made by rollers and measures in coal - rolling plants

    冷軋廠冷線堿槽浸入輥對鋼板表面形成損害及防治
  17. Abstract : the present paper introduces the history of development, operating principle and characteristics of the rolling mill with axial shifting roll as well as its application in the country, analyzes the feature of the shape control for the currently most broadly applied hc rolling mill and discusses in detail the setting up of the roll system

    文摘:介紹了軋輥軸向移動軋機的發展過程、工作原理、形式特點以及在國內的應用情況，分析了目前應用最普遍的hc系列軋機的板形控制特性，並對輥系配置進行了深入的探討。
  18. 1 a set of 20 - rool mill with four vertical posts wv20seh55 - 300 1150 introduced from german sundwig. the mill may yearly produce 80, 000 tons of various markings of cold - rolled stainless steel, silicon steel, and carbon steel sheets with 0. 1 mm in thickness and 0. 01 in tolerance

    1德國引進森德威wv20seh55 - 3001150四立柱式廿輥軋機一臺套，年產量8萬噸，該設備可生產成品最薄厚度至0 . 1mm的各種牌號的冷軋不銹鋼硅鋼普碳鋼板，公差可達到0 . 01mm 。
  19. By comparing the values of the traditional rolling force model and the prediction model by cmac with the measured ones, the precision of the prediction model by the fuzzy cmac is much better than that of the traditional rolling force model and is more suitable for online use of a multi - roll cold tandem mill controlled by computer, which also meets manufacturing requirement of the field and receives better control effect of the shape and thickness

    通過對傳統軋制力模型計算值、小腦模型預報計算值與實測值進行對比分析可知，基於模糊小腦模型神經網路的多輥冷連軋機軋制力預報模型具有較高的計算精度，更適合於多輥軋機在線計算機過程式控制制的應用，滿足現場在線生產的要求，取得良好的板形板厚控制效果。
  20. Hongtai steel flat plate, which adopts excellent color - coated plates, are roof and wall materials after being rolled on automatic production line, it owns merits of lightness, strength, bright color, beautiful appearance

    鴻泰鋼構面板採用優質的彩色塗層鋼板，經自動型生產線輥軋而成的屋面和墻面材料。
分享友人
分享到 Line

分享到臉書