輥軋機 的英文怎麼說

中文拼音 [gǔnyàjī]
輥軋機 英文
reduction roller mill
  • 輥 : 名詞[機械工程] （能滾動的圓柱形機件） roller
  • 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
  • 機 : machineengine
  1. Through examining the roll strength in the leaf blade special - purpose rolling machine, this article has confirmed the feasibility of rolling leaf blade in the new rolling machine

    摘要通過對葉片專用輥軋機軋輥的強度進行校核，驗證了在新型輥軋機上軋制葉片的可行性。
  2. There are sever kinds of strap mills : horizontal mills - - two roll strap mills and four roll strap mills, and vertical mill with upper drive and bottom drive

    帶鋼軋機有二輥帶鋼軋機和四輥帶鋼軋機，都是水平輥軋機，還有上傳動立輥軋機和下傳動立輥軋機。
  3. In view of this situation this article has conducted research to the design of metallurgy auxiliary biography with the frequency conversion table electrical machinery first multianalysis to the frequency changer and the frequency conversion table electrical machinery movement characteristic is carried out, the voltage waveform harmonious which the frequency changer outputs is big, attacks in a big way, and the voltage climbing rate reaches as high as 6600v / mu s which is 20 times ordinary sine alternating voltage, the rolling mill auxiliary biography table set the extremely strict request to the electrical machinery ; its movement frequency is very low, rate frequency in 8 - 20hz ; the velocity modulation scope is wide, the lowest movement frequency lowers to 1hz, and the starting number of times is quite frequently, each hour reaches as high as 600 - 800 time, the impact shoulders in a big way, the overload capacity request is high

    針對這一情況本文對冶金輔傳用變頻輥道電機的設計進行了系統研究。首先對變頻器和變頻輥道電機的運行特性進行詳細分析，變頻器輸出的電壓波形諧波大，沖擊大，電壓上升率高達6600v / s ，是普通正弦交流電壓的20倍;軋機輔傳輥道對電機提出了十分嚴格的要求:其運行頻率很低，額定頻率在8 - 20hz ;調速范圍寬，最低運行頻率低到0 . 5hz ，起動次數相當頻繁，每小時高達600 - 800次，沖擊負荷大，過載能力要求較高。
  4. The investigation of aluminium foil thickness auto - adjusting system in four rollers non reversing cooling rolling mill

    四輥不可逆鋁箔冷軋機箔厚閉環調節系統淺析
  5. The development of heavy plate mill and the common characteristics of the mill revamping were summarized, and the production technologies, such as control links of tmcp, appliction of edger mill and the processing of steckel mill for plate were introduced

    綜述了厚板軋機的發展及其技術改造的特點；介紹了厚板生產tmcp技術的控制環節，立輥軋機的應用以及卷軋中板的生產工藝特點。
  6. Fictious simulation of high - speed roll casting has been carried out on the basis of the fact. the results showed that roll casting speed increase with the decrease of the thickness of the strip, and the peak value of rolling pressure decrease with the increase of roll casting speed and thickness of strip or the increase of roll casting zone. the designed parameters of mechanical capabilities of the roll caster should be raised when rolling pressure increase with roller diameter increase

    研究結果表明，減薄鑄軋板坯厚度可提高鑄軋速度；隨著鑄軋速度降低、鑄軋區增大與鑄軋坯厚度減薄，軋制壓力峰值增大；隨著鑄軋輥徑增大，軋制壓力增大，因此鑄軋機力能設計參數也要相應增大。
  7. Centrifuge casting of roll collar for wire preliminary finishing mill

    線材預精軋機用輥環的離心鑄造
  8. Drawing module, which is graphic system of 1c ad, consists of geometric and three - dimensional parameterization model design of work roll, backup roll, mill framework and finishing mill

    繪圖模塊由智能cad的圖形處理部分組成，包括工作輥、支撐輥、機架和精軋機的幾何建模和三維參數化設計。
  9. Responding to the call of industrial policy adjustment in our country, yaoyu special steel company has started replacing hot - rolling with cold - rolling in the production of electric steel since 2003. it entrusted xinye gaoke group to make design and build the production line of cold - rolled electric steel with annual output of 200 thousand tons. after three years of construction, it has achieved the successful trial production of 20 - roll mill and continuous annealing and coating machine imported from germany

    耀宇特鋼從2003年開始，響應國家產業政策調整的號召，開始電工鋼以冷代熱技改工程，委託新冶高科集團原冶金部鋼研院設計，進行年產20萬噸冷軋電工鋼生產線的建設，經過近三年的建設，目前從德國引進的20輥軋機及連續退火塗層機組均已試產成功，為提高產品的性能和質量，同時提升我國電工用薄鋼板的生產作出了卓越的貢獻。
  10. The rolls pulled up on pour front lawn ; the chauffeur hauled up in front of us

    在傾盆大雨的時候輥軋機在草坪前面停下；司機在我們前面。
  11. Automatic rolling control system for four - high mill in citi

    公司軋鋼廠四輥軋機自動軋鋼系統
  12. Works on the bending roll system of four - roll rolling mill, the workroll shape variation caused by the force of bending roll and the contact stress between rolls was researched with the fem software ansys, the maximum deformation of the work roll was calculated, and the curve of the gap adopting the least - squares method was fitted, which set the base of the further calculation of load - gap shape

    摘要以四輥軋機的彎輥系統為研究對象，利用有限元分析軟體ansys研究彎輥力和輥間接觸應力引起工作輥形狀的變化，計算工作輥彎曲的最大變形量，並用最小二乘法對輥縫曲線進行擬合，為進一步計算有載輥縫形狀提供可靠的理論依據。
  13. Considering different microstructures and properties of metal of hardened layer and the core of back - up roller, the distributions of shear stress below surface and the contact stress between work roller and back - up roller of a four - high - mill were simulated with nonlinear fem

    摘要考慮軋輥表面淬硬層與其心部金屬材料組織性能的差別，採用非線性有限元方法對四輥軋機的工作輥與支撐輥間接觸應力及輥內剪應力分佈進行模擬，並將模擬結果與傳統強度校核方法進行了對比分析，研究了軋輥淬硬層厚度對輥間接觸應力的影響規律。
  14. Influence of electric grid voltage fluctuation on main motor drive system for four - high medium plate mill and its solution are introduced

    摘要介紹了電網電壓波動對中板四輥軋機主電機傳動系統的影響和解決方法。
  15. According to recording data of higher level monitor and control system when main motor drive system for four - high medium plate mill is operated, and relation between armature voltage of dc electromotor and ac input voltage of inverter, trip cause of dc fast automatic switch was analyzed in detail, and specific countermeasure and measures are given

    根據中板四輥軋機主電機傳動系統運行時的上級監控系統記錄數據，以及直流電機電樞電壓與變流器交流側輸人電壓的關系，詳盡地分析了直流快速自動開關跳閘故障原因，並提出具體的對策及措施。
  16. Introduction of on - line operating condition monitoring system for medium heavy plate mill

    四輥軋機工況在線監測系統淺析
  17. Rubber and plastics machines - two roll mills - safety requirements ; german version en 1417 : 1996

    橡膠機械和塑料機械.雙輥軋機.安全性要求
  18. This paper establishes mathematical mode based two rolls mill and four rolls mill in aluminum product mill, and introduces the emulating with matlab

    本文根據張家口鋁製品廠的二輥軋機和四輥軋機中的apc控制系統建立模型，選擇控制方案。
  19. 1 a set of 20 - rool mill with four vertical posts wv20seh55 - 300 1150 introduced from german sundwig. the mill may yearly produce 80, 000 tons of various markings of cold - rolled stainless steel, silicon steel, and carbon steel sheets with 0. 1 mm in thickness and 0. 01 in tolerance

    1德國引進森德威wv20seh55 - 3001150四立柱式廿輥軋機一臺套，年產量8萬噸，該設備可生產成品最薄厚度至0 . 1mm的各種牌號的冷軋不銹鋼硅鋼普碳鋼板，公差可達到0 . 01mm 。
  20. By comparing the values of the traditional rolling force model and the prediction model by cmac with the measured ones, the precision of the prediction model by the fuzzy cmac is much better than that of the traditional rolling force model and is more suitable for online use of a multi - roll cold tandem mill controlled by computer, which also meets manufacturing requirement of the field and receives better control effect of the shape and thickness

    通過對傳統軋制力模型計算值、小腦模型預報計算值與實測值進行對比分析可知，基於模糊小腦模型神經網路的多輥冷連軋機軋制力預報模型具有較高的計算精度，更適合於多輥軋機在線計算機過程式控制制的應用，滿足現場在線生產的要求，取得良好的板形板厚控制效果。
分享友人
分享到 Line

分享到臉書