輸出邊 的英文怎麼說

中文拼音 [shūchūbiān]
輸出邊 英文
output side
  • 輸 : Ⅰ動詞1 （運輸; 運送） transport; convey 2 [書面語] （捐獻） contribute money; donate 3 （失敗） l...
  • 邊 : 邊Ⅰ名詞1 （幾何圖形上夾成角的直線或圍成多邊形的線段） side; section 2 （邊緣） edge; margin; oute...
  • 輸出 : 1 （從內部送到外部） export 2 [電學] output; outcome; outlet; out fan; fanout; 輸出變壓器 output ...
  1. Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle

    流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。
  2. Another great feature is in - coming and out - going connector handlers that show up on the sides of the bean shape when you hover over it, or when you select the element and press the space bar

    另一個重要的特性是傳入的（ in - coming ）和輸出的（ out - going ）連接器處理程序，當用戶使鼠標停留在bean上或者選擇元素並且按下空格條時這些連接器處理程序會顯示在bean的側邊。
  3. The basic thought of the csapfba algorithm is : the edge routers perform the state management per flow, and the edge routers differentiate between the marked flows and the non - marked flows, and the edge routers insert the relevant information into the packet header by using dynamic packet state ; the core routers divide the output link bandwidth into two parts in the light of the state information of the packet header by using class - based queueing, and the core routers allocate proportionally the bandwidth to the marked flows according to their service profiles and the current network load, and the core routers allocate the bandwidth to the non - marked flows according to the principle of max - min fairness, and the csapfba algorithm can adaptively dynamically adjust the bandwidth allocation between the marked flows and the non - marked flows

    本文在csfq演算法的基礎上，提出了一種核心無狀態的自適應的成比例公平帶寬分配csapfba （ core - statelessadaptiveproportionalfairbandwidthallocation ）演算法。 csapfba演算法的基本思想是：在邊界路由器完成基於每個流的狀態處理，將所有的流分成標記流和非標記流兩種類型，採用dps技術將有關信息編碼進分組頭；在核心路由器根據分組頭中攜帶的狀態信息採用cbq策略，將輸出鏈路帶寬分成兩部分，對標記流根據當前的網路負荷按照服務規格成比例地分配帶寬，對非標記流按照最大最小公平性原則分配帶寬，並且能自適應地動態調整帶寬分配的比例。
  4. In chapter four, according to the analysis on the boundary theory and velocity field of main fluid zone of two - phase fluid pumps, the parameter equations of vane ' s modular curve of centrifugal pump are given, which contact the boundary " layer and eular theory of two - phase fluid pump by the fixing angel of vane as variable and leading into the velocity coefficient a. the results show that, in designing process of vane ' s modular curve of centrifugal pump, the determination of the total shape and parameters relates the flow properties of two - phase fluid and output ability of pump, or the design of the modular curve of centrifugal pump is the kernel of hydraulic design

    第四章依據固液兩相流泵的邊界層理論及對主流區速度場的分析，給出了離心泵葉片型線的參數方程；它是以葉片安裝角為參變數，以引入的速度系數k _ v作為中間因子，將兩相流泵的邊界層理論和歐拉理論聯系起來? ?它說明了這樣一個事實，在離心泵葉片型線的設計過程中，它的整個形態或參數的確定都關繫到兩相流體的流動特性和泵的輸出能力，或者說，離心泵型線的設計是其水力設計的核心。
  5. In the aspect of output characteristics, after applying the boundary conditions and the continue condition of two segments, the correlative dependence of average photon density in each segment has been obtained. combining this dependence with the threshold conditions, the theory foundation is settled

    在兩段式dfb激光器的輸出特性研究方面，利用邊界條件以及兩段之間的連續條件，導出了兩段平均光子數密度之間的依賴關系；這和兩段式dfb激光器的閾值條件表達式相結合，構造了本文研究激光器輸出特性的理論框架。
  6. We apply the agrawal ' s theory model of soa, and study the temporal characteristics of the output pulse for input picosecond optical pulses with different sharpness edges passing through a semiconductor optical amplifier, and find that the peak power and the pulse width of the output pulse depend on the input pulse peak power, the sharpness degree of the input pulse edge and the bias current of soa

    本文應用agrawal的關于soa理論模型，詳細研究了具有不同陡峭邊沿的皮秒超高斯光脈沖經soa后的時域特性的變化，發現輸出脈沖的峰值功率、脈沖寬度與輸入脈沖的峰值功率、輸入脈沖邊沿的陡峭程度以及soa的偏置電流密切相關。
  7. Most of the time, they are required to output even illumination patterns for back, side or front lighting in information panels or display systems

    當代大多數而言，他們對于輸出的要求甚於照明在資訊配電板或顯示系統中背面的、側邊的或前面的照度樣板。
  8. The product is suitable for double straight line smoothing of grinding flat glass. coarse grinding, fine grinding, and polishing can be done at one time. adopt plc control system, which sets processing parameters via interface, and finishes processing at one time, ti has stable bottom structureprecise and smooth transmission system, the transmission belt drive adopts strong power and tran - sfrequency motor to control speed, constant power, constant rule, output and advanced equipment to control, completed product has high polishing level, which is an ideal option assistant processed equipment of processing delicacy glass and furniture glass factory

    本產品適用於磨削平板玻璃是雙直線平邊，粗磨精磨拋光一次完成採用plc控制系統通過界面設定加工參數次完成加工，具有穩重扎實的底座結構，精確流暢的傳動系繞，傳送皮帶驅動採用功率變頻電機調速控制，恆功率恆扭矩輸出和高配置的控製成品拋光亮度高是加工精品玻璃和傢具玻璃廠家使用的最佳輔助加工設備。
  9. This machine is used for straight - line bevel cutting and bevel grinding and polishing for flat glass, in certain condition, it can be also used in bevel cuttig, bevel grinding and polishing for soft stone panel. the contrilling system adopts plc, it can accomplish automatic grinding cutting after entering processing parameter, convery speed adopts speed adjustment of fre quency conversion, direct drive of wheel head motor, all motions for joining in parameter adjustment completely adopt straight - rolling guide - track with front beam and wheel head lifting lntegrally. the transmission of input and output adopts synchronization tooth belt and photo - electricity switch positioning, and position limitation of two pass is much more reliable

    Sxm371pa型玻璃直線斜邊磨邊機是用於玻璃直線斜邊斜切，斜磨及光拋的專用設備，在一定條件下也可以用於軟石板材的斜切斜磨及拋光。控制系統採用plc控制。輸入加工參數后可自動完成磨削傳送速度採用變頻調速，磨頭電機直接傳動，所有加工參數調整運動副全部採用直線滾動導軌，前梁與磨頭整體升降，輸入輸出傳送採用同步形帶，光電開光定位，雙行程限位更安全可靠。
  10. It is only using one high voltage cable to serve as the common one - turn primary winding for all the output transformers. in addition, the isolation voltage level for the transformers can be made very high

    使用超高壓絕緣的電纜線作為所有輸出變壓器單匝的原邊繞組，電源輸出之間的隔離電壓可以達到相當高的等級。
  11. I just tweak the new xslt file so that it will remove the left - hand " link bar " and perform a few other minor changes to the output html when it processes documentation pages

    我僅僅調整了新的xslt文件，以便它可以除去左邊的「鏈接欄」並在處理文檔頁面時對輸出html作其它幾點較小的更改。
  12. In order to eliminate the voltage oscillation caused by the reverse recovery of the rectifier diodes, a resonant inductance and two clamping diodes can be introduced to the primary side

    為了消除輸出整流管的電壓尖峰，可以在原邊加入一個諧振電感和兩個箝位二極體。
  13. Automatic computation and modification of the dimension, the number of total heat tubes and rows, the body line of layout areas and other results involved. 4. the programming of various functional models and their communication, coded with visual lisp and vba and based on the opening structure of autocad and its entity database

    標示最大布管邊界，自動標注尺寸，自動修改並輸出布管參數及結果，包括：自動計算並輸出每一管程的管根數、起始排數、終止排數，自動計算並輸出每排熱管根數與拉桿根數。
  14. The algorithm has many advantages such as the input format and output format being uniformed, high efficient, wide application, etc. it has abroad market values in many domains, such as the weather character demonstration, computing and the demonstration of anomalous graphics, etc. we know that curves can be approached by mini line - segments, so the boolean operations between almost all regions can be implemented by this algorithm

    本演算法具有輸入、輸出數據格式統一、效率高、應用面廣等優點。在實現天氣氣象圖的演示、各種不規則圖形的顯示和計算等領域具有很廣闊的市場前景。由於曲線邊界可以由小線段組成的多邊形來逼近，所以通過本演算法，我們還可以實現任何邊界區域間的布爾操作。
  15. During this time, line buffer 2, which was presumed to be full, will empty itself into the output paths, on the right of the illustration.

    這時，行緩沖器2假定是滿載的，則向圖右邊的輸出通道卸載。
  16. This paper describes an aag ( attributed adjacency garaph ) based method of machining features recognition for shaft kind parts and 2. 5d parts on the acis platform, which can effectively recognize the main and assistant feature of these kinds of parts. using the class library provided by acis, all the geometrical information for defining a feature can be acquired. finally a xml neutral file describing the recognition result is provided for the later capp process and the generation of nc code

    本文首先分析三維實體邊界模型的特徵識別方法及其特點，繼而採用基於屬性鄰接圖的特徵識別方法，研究了軸類零件及2 . 5維零件的加工特徵的分類及其識別，並在acis平臺上開發了相應的軟體原型系統，有效地識別該類零件的主特徵和常見的輔助特徵，且利用acis提供的類庫介面提取模型底層的幾何參數，得到定義各項特徵所需的幾何尺寸信息，最後以xml中性文件的形式輸出識別結果，為后續進行的工藝規劃、加工代碼生成提供初始數據，從而為cad / capp / cam的集成提供有效的方法。
  17. Initially the xinanjiang model was calibrated using the shuffle complex evolution method ( sce - ua ) under ideal situations - where the data inputs are assumed to be error free and the flow series for which the model results are fitted are generated from a known set of model parameter values

    起先在理想的條件下我們用單純多邊形進化（ sce - ua ）的演算法對新安江模型進行了計算，模型的輸入假設是無誤差的，用一套已經知的參數來計算輸出的流量系列。
  18. A series of lasers with about 0. 8nm spacing have been achieved. the smsr is higher than 54db

    獲得了一系列波長間隔約為0 . 8nm ，邊模抑制比大於54db的激光輸出。
  19. Then a thorough analysis to the bias - magnetic of ppfc is made. the retraining effects of the main parameters ( include clamping capacitance c, output filter inductor lf, load r, the leakage inductor ls and source winding resistance r ) are studied under the conditions of different von, different ton and different winding parameters. then a conclusion can be drew, that the smaller lf and the bigger r are, the better the bias - magnetic is restrained and c has a best value to retrain the bias - magnetic

    分別對管壓降不同，導通時間不同以及兩原邊繞組參數不一致（包括漏感、電阻、激磁電感三種情況）的情況下，主要參數（包括箝位電容c 、輸出濾波電感lf 、負載r 、原邊繞組漏感ls 、原邊繞組電阻r ）對偏磁的抑制作用進行了模擬分析研究，得出lf越小， r越大時激磁磁勢偏移量ni越小， c在其他參數確定時對抑制偏磁有最優值等結論，為參數的優化設計提供了依據。
  20. The side mode suppression ratio about 39db is realized. 5. a tunable cladding - pumped yb3 + - doped fiber laser system is reported

    55 m可調諧光纖光柵外腔半導體激光器，得到調諧范圍為7nm 、邊模抑制比達39db的激光輸出。
分享友人
分享到 Line

分享到臉書