輸出電阻 的英文怎麼說

中文拼音 [shūchūdiànzǔ]
輸出電阻 英文
output resistance
  • 輸 : Ⅰ動詞1 （運輸; 運送） transport; convey 2 [書面語] （捐獻） contribute money; donate 3 （失敗） l...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 阻 : 動詞（阻擋; 阻礙） block; hinder; impede; obstruct
  • 輸出 : 1 （從內部送到外部） export 2 [電學] output; outcome; outlet; out fan; fanout; 輸出變壓器 output ...
  • 電阻 : （物質阻礙電流通過的性質） resistance; electric resistance （電路中兩點間在一定壓力下決定電流強度...
  1. Ohmic resistance measured between the output voltage connections

    輸出電路測得的電阻歐姆
  2. 1 m 0. 5, the phase - shifted angle 6 is controlled in term of sine law which makes the magnitude of resonant voltage track a reference sine voltage, and the resonant voltage is rectified, filtered, inverted and then the better sine - voltage output is obtained, theoretical analysis and experimental results show that for the resistive load and inductive load, the switches of leading leg of the phase - shift - controlled circuit are always turned on at zvs, and ones of lagging leg are turned on at zvs ( < 0 ) or turned off at zcs ( ( > 0 ), moreover, all switches in the low - frequency inverter are always turned on and off at zvs, the measured circuit efficiency for rated load reaches up to 88 %

    從功率單向流動角度出發，提出了一種lcc諧振型恆頻移相單相高頻鏈逆變電路拓撲，在調制系數0 . 1 m 0 . 5情況下，控制移相角按正弦規律變化，使諧振電壓脈沖列的幅值追蹤參考正弦電壓信號，經過整流、濾波、低頻逆變，從而獲得正弦度較好的輸出電壓。理論分析和實驗結果證明對于阻性負載或阻感性負載，移相全橋具有超前橋臂零電壓開通，滯后橋臂或者零電壓開通（ _ 0 ）或者零電流關斷（ _ 0 ）的軟開關特性，而低頻逆變器的各個開關均實現零電壓條件下的開通與關斷。
  3. The study shows that the output pulse value of resistance absorption equipment is related to the chopper switch conduction ration and the selection of lagging angle

    研究表明，地面電阻吸收裝置的輸出電流脈動與斬波器的導通比、各支路斬波器的開關滯后角有關。
  4. Among them insulated the insulation resistance testing instrument to adopt the high direct voltage testing method ; the ac insulate testing instrument adopt to the instrument of ac high voltage, and we also designed the protected circuit with excessive current ; the coil insulate testing instrument is adopt surge voltage impact testing method

    其中絕緣電阻測試儀採用了直流高電壓測試法；工頻耐壓測試儀採用高壓工頻測試，並設計了過流保護電路；匝間耐壓測試儀採用浪涌電壓測試法，並設計了多路可控硅控制脈沖輸出電路。
  5. The synchronous rectifying and low power sampling technology is used to reduce the power consumption, flexible external loop compensation, error amplifier output clamp are adopted for better system large signal response. the piecewise slope compensation technology is employed to minimize the consequence of over compensation. the sensor resistor is externally connected, which realize output voltage programmable. the overheat protection and under voltage protection modules are integrated in the die to allow the reliable operation of the system

    同時，電路設計採用同步整流技術、低功耗電流采樣技術降低功耗，提高轉換效率;採用靈活的外部環路補償技術、誤差放大器輸出嵌位技術以實現良好大信號特性;採用分段斜坡補償技術，消除不穩定因素，並最大程度地減小過補償帶來的問題;採用外接輸出采樣電阻的方式，實現輸出電壓的可編程。
  6. According to the request of this subject, we have developed the system hardware and software for the slave device and the inspection software running on the pc. in this paper all of the followings is illustrated detailedly, such as the research on the principles of measurement and its realization, three means of water - level measurement that are separately based on photo electricity coder, pressure sensor and potentiometer ; selection of the microchip, we choose an advanced integrated soc ( system on chip ) microchip c8051f021 as the main controller ; realization of signal sampling, processing and its conversion in the mcu ; application of high precision 16 bits adc cmos chip - - ad7705 in our system, designing its interface with the microchip and relevant program ; using a trickle charge timekeeping chip ds1302 in the system which can provide time norm and designing of its i / o interface and program ; additionally, a 4 ~ 20ma current output channel to provide system check - up using ad421. in the system, ad421, ad7705 and the microchip compose spi bus ; to communicate with the master pc, here we use two ways which are separately rs232 and rs485 ; moreover, there are alarm unit, keyboard unit, power supply inspection unit and voltage norm providing unit in the system

    針對研製任務的要求，課題期間研製了下位機系統硬體和軟體，開發了上位機監控軟體，其中所作的具體工作包括：測量原理的研究和在系統中的實現，在本次設計中用三種方法來進行水位測量，分別是旋轉編碼器法、液位壓力傳感器法和可變電阻器法；主控晶元的選擇，我們選用了高集成度的混合信號系統級晶元c8051f021 ；實現了信號的採集和處理，包括信號的轉換和在單片機內的運算；高集成度16位模數轉換晶元ad7705在系統中的應用，我們完成了它與單片機的介面設計及程序編制任務；精確時鐘晶元ds1302在系統中的應用，在此，我們實現了用單片機的i o口與ds1302的連接和在軟體中對時序的模擬，該晶元的應用給整臺儀器提供了時間基準，方便了儀器的使用；另外，針對研製任務的要求，還給系統加上了一路4 20ma模擬信號電流環的輸出電路來提供系統監測，該部分的實現是通過採用ad421晶元來完成的，本設計中完成了ad421與單片機的spi介面任務，協調了它與ad7705晶元和單片機共同構成的spi總線系統的關系，並完成了程序設計；與上位機的通信介面設計，該部分通過兩種方法實現： rs232通信方式和rs485通信方式；系統設計方面還包括報警電路設計、操作鍵盤設計、電源監控電路設計、電壓基準電路的設計。
  7. Traditionally, the resolving - transformer consists of former windings and vice windings. but the resulting output voltage will have aberrance owing to the existence of winding resistors and reactance leakage

    傳統上的旋轉變壓器常採用原副線圈來組成，由於線圈電阻和漏抗的存在，將使最終輸出電勢出現畸變。
  8. The expression can be used in calculation for relationships of the input voltage, output voltage and device geometry parameter

    用漸近解的分析方法對所求到的解進行簡化，導出了硅橫向壓阻效應四端壓力傳感器的輸出電壓表達式。
  9. The thesis has done the widespread investigation and study to the domestic and foreign ’ s technologies of analogy low voltage and low power, and analyzes the principles of work, merts and shortcomings of these technologies, based on the absorption of these technologies, it designs a 1. 5v low power rail - to - rail cmos operational amplifier. when designing input stage, in order to enable the input common mode voltage range to achieve rail - to - rail, it does not use the traditional differential input pair, but use the nmos tube and the pmos tube parallel supplementary differential input pair to the structure, and uses the proportional current mirror technology to realize the constant transconductance of input stage. in the middle gain stage design, the current mirror load does not use the traditional standard cascode structure, but uses the low voltage, wide - swing casecode structure which is suitable to work in low voltage. when designing output stage, in order to enhance the efficiency, it uses the push - pull common source stage amplifier as the output stage, the output voltage swing basically reached rail - to - rail. the thesis changes the design of the traditional normal source based on the operational amplifier, uses the differential amplifier with current mirror load to design a normal current source. the normal current source provides the stable bias current and the bias voltage to the operational amplifier, so the stability of operational amplifier is guaranteed. the thesis uses the miller compensate technology with a adjusting zero resistance to compensate the operational amplifier

    本論文對國內外的模擬低電壓低功耗技術做了廣泛的調查研究，分析了這些技術的工作原理和優缺點，在吸收這些技術成果基礎上設計了一個1 . 5v低功耗軌至軌cmos運算放大器。在設計輸入級時，為了使輸入共模電壓范圍達到軌至軌，不是採用傳統的差動輸入結構，而是採用了nmos管和pmos管並聯的互補差動輸入對結構，並採用成比例的電流鏡技術實現了輸入級跨導的恆定;在中間增益級設計中，電流鏡負載並不是採用傳統的標準共源共柵結構，而是採用了適合在低壓工作的低壓寬擺幅共源共柵結構;在輸出級設計時，為了提高效率，採用了推挽共源級放大器作為輸出級，輸出電壓擺幅基本上達到了軌至軌;本論文改變傳統基準源基於運放的設計，採用了帶電流鏡負載的差分放大器設計了一個基準電流源，給運放提供穩定的偏置電流和偏置電壓，保證了運放的穩定性;並採用了帶調零電阻的密勒補償技術對運放進行頻率補償。
  10. 2, design a structure makes the liner output higher to 160mv with a liner input about 150 in bridge of spin - valve gmr. in comparison of some typical mr angular sensors it ' s output make a great progress

    2 ，設計了一種結構使自旋閥gmr晶元組成的橋路輸出電壓信號線性區達到約150 ，輸出幅度達到了160mv ；相比一些典型的磁阻非接觸式角度傳感器，量程獲得了可觀的擴展。
  11. The traditional bandgap reference circuit was improved in the design, which includes the applying of self - bias structure and cascode structure, output of the opamp was used as self - bias voltage, saving bias circuit, and then it was helpful to get low power consumption. through using poly resistance of high value with low temperature coefficient, we reduced the influnce to circuit, if power supply did not change, we must decrease operating current to decrease power consumption, and increasing value of resistor could decrease the operating current efficiently. poly resistance of high value had large value of squared resistor, so we could save layout area

    對傳統帶隙基準電路進行了改進設計，採用自偏置結構和鏡像電流鏡結構，利用運放的輸出電壓作為運放的偏置電壓，節省了偏置電路，降低了功耗;使用低溫度系數的多晶硅高值電阻，降低了電阻溫漂對電路的影響;在電源電壓不變的情況下，為了減小功耗就必須減小工作電流，而增大電阻的阻值能有效地減小工作電流，多晶硅高值電阻的方塊電阻很大，可以節省版圖面積。
  12. By the means of theory, simulation and experiment, the second part of this paper is then analyzed which is on the equivalent output resistance and inductance of the selected inverter and the effect to the output voltage ' s amplitude and phase caused by the different values of the inverter ' s component. it is concluded that by selecting certain precision level components, the difference of the output voltage amplitude is much greater than that of the output voltage phase

    其次通過理論、模擬和實驗分析了本文所採用的電壓電流雙閉環瞬時控制方式逆變器的等效輸出阻抗和兩臺逆變器器件差異對輸出電壓的幅值差和相位差的影響，從而得出選用一定精度的器件，兩臺逆變器輸出電壓的幅值差比相位差大得多的結論。
  13. By carefully selecting the voltage taps, the correct voltage output to match the resistance of the elements over their complete useful life can be made

    仔細選擇電壓插孔，選擇和電阻相匹配的輸出電壓值，這樣可以延長其有效使用壽命。
  14. The ze10. 006 produces a current loop output which can be easily converted to a voltage output by adding a resistor

    Ze10 . 006輸出電流迴路，可以通過增加電阻方便地轉換成電壓輸出。
  15. Selecting the 0 - 20 ma output and placing a 500r resistor across the current output will generate a 0 - 10 v dc analogue signal

    選擇0 - 20 ma的輸出時，在輸出電流迴路中放置一個500r的電阻可以產生0 - 10v的直流模擬信號。
  16. Maximum output resistance

    最大輸出電阻
  17. In this paper, basic circuit models of cc - current mirror and active impedance are analysed and a new active feedback current mirror is proposed which can achieve larger output impedance, higher current transfer precision, lower power and wider signal dynamic swing

    系統地分析了電流傳送器的組成模塊? ?電流鏡和有源電阻，同時提出了一種改進型有源反饋電流鏡電路。該電路能大大提高輸出電阻，同時能保持原電路的電流轉換高精度、低功耗、更寬更良好的輸出電壓動態范圍。
  18. Also, by using the hot - carrier immiunity analog circuit structure, the output resistance degradation caused by the hot - carrier degradation is deeply supressed and the small - dimensional effect can be improved shown by the spice 3f5 simulation results, and the gain degradation of a cmos o peration amplifer after 10 years operation decreases from 23 % to 10 % with this structure according to bert2. 0 simulation

    而串聯常開n mosfet的模擬電路結構可使n mosfet輸出電阻的退化大為減小同時還可改善器件小尺寸效應引起的輸出電阻下降：採用該結構的os運放與未採用的相比，其十年工作后增益的退化由23下降為10 。
  19. Analysis of the output resistance of stabilized power supply in series

    串聯型直流穩壓電源輸出內阻的分析
  20. Abstract : after the relationship between radial and tangential strains and resistance changes of strain gage on the surface of elasticity pressure sensor is established by finite element method, the output voltage is related to the resistance changes in the electrical bridge, and the nonlinear precision of this kind of pressure sensor is analyzed

    文摘:本文用有限元方法分析平膜片式壓力傳感器彈性元件表面徑向應變及切向應變與薄膜應變片阻值變化的聯系后，根據電橋原理得到與其輸出電壓之間的關系，最終並分析了傳感器之非線性精度
分享友人
分享到 Line

分享到臉書