轉彎誤差 的英文怎麼說

中文拼音 [zhuǎnwānwùchā]
轉彎誤差 英文
turn error
  • 轉 : 轉構詞成分。
  • 彎 : Ⅰ形容詞（彎曲） curved; bent; crooked; flexuous; tortuous Ⅱ動詞1 （使彎曲） curved; bend; flex 2 ...
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 轉彎 : wheel; swerve; turn a corner; make a turn
  • 誤差 : error
  1. When there is no or lesser undercut, we can use the bend stress ' s algorithm of involute gear to calculate approximately the bend stress of gear with meshed medium belt, what we to do is to transit the interrelated shift coefficient to the according radial minus shift coefficient of involute gear, and the error can be controlled in 10 %

    在不產生或少量根切時，可用漸開線徑向變位齒輪的彎曲應力計算方法來近似計算帶式嚙合介質齒輪的彎曲應力，只需將關聯變位系數轉化為相應的漸開線齒輪徑向變位系數即可，其誤差在10 %以內。
  2. As a result, shifting of the fundamental frequencies and redistribution of stress in the blade base possibly cause failure of the blade. a three - dimensional finite element model of a blade and its fir - tree attachments have been constructed and analyzed with taking into account of contact nonlinearity in the attachments and large deformation effect of the blade. the geometry mismatch was introduced into the finite element model by defining gaps between two contact surfaces in the attachments

    分析結果表明葉根誤差發生的位置對葉片彎曲振型的固有頻率影響較大，對扭轉振型影響較小;誤差的大小對葉片各階固有頻率影響均較小，但對葉根應力分佈有影響;比較發現，在計算固有頻率時，將葉片在葉根處簡單地處理成固支位移邊界是不合理的。
  3. The results of analysis show that : 1 ) doi of the pin - axis errors, especially the crank - pin - axis errors, is bigger than other axis errors ; 2 ) from the calculating results of doi of the errors of the different kinematic pairs, doi of rotate - completely pairs is bigger than that of oscillate pairs ; 3 ) the forced coupler - deformations resulted from the constraints out of motion plane consist of twisting and bending deformation, and the deformations are variat

    （ 4 ）首次提出了運動副誤差對平面連桿機構約束不確定性影響度的評判指標和單因素定量分析方法，得到了機構中不同運動副的不同平面內的誤差對機構性能的影響程度。本文的分析計算結果表明，平面連桿機構中的非平面約束所造成的連桿強制變形中既有扭轉變形又有彎曲變形。
  4. To work the line control parameters out, the thesis deduced the formula calculating the equivalent traffic volume of intersection, put forward and deduced the elementary saturated traffic volume of intersection, gave the bounds of all the parameters needed for the stop delay of vehicle at the intersection. taking the influence of turning vehicles and the difference of the importance between two different adjoined segments of the arterial street into account, the thesis established the formula calculating the traffic volume of the arterial street when the offsets of all the intersections are optimized

    論文推導了交叉口當量交通量的計算公式，提出並推導了交叉口飽和交通流率基本值；明確給出了計算車輛在交叉口上的延誤所需的各個參數的范圍；考慮了各個交叉口轉彎車輛的影響和主幹道上不同路段的重要性差異，建立了主幹道交通量的計算公式。
分享友人
分享到 Line

分享到臉書