轉矩限制器 的英文怎麼說

中文拼音 [zhuǎnjǔxiànzhìqì]
轉矩限制器 英文
torque limiter
  • 轉 : 轉構詞成分。
  • 矩 : 名詞1. （畫直角或正方形、矩形用的曲尺） carpenter's square; square2. （法度; 規則） rules; regulations 3. [物理學] moment
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 限制 : place [impose] restrictions on [to]; astrict; restrict; limit; confine; shut down on [upon]: 限制...
  1. In the simulation work, one 1. 5kw and one 18kw induction motors ? control system were simulated and two simplified control scheme were proposed. when developing the program in tms320f240 dsp, this paper solved two practical problems : the finite - length effect and dc bias effect. finally, sensorless control system based on adaptive filter theory are tested on the platform of 1. 5kw induction motor, the results show that the scheme ? performance is good

    在模擬過程中，針對1 . 5kw和18kw異步電機進行了模擬，並在此基礎上提出兩種簡化控制方式；在tms320f240的具體編程過程中，分別對自適應濾波器的有限字長效應、直流偏置效應等非理想因素進行了修正和補償；最後，在1 . 5kw微型異步電機上進行了轉矩閉環無速度傳感器實驗，實驗結果表明了演算法完全可以達到預期的目標。
  2. Aiming at wide variations in loads and moment of inertia, large disturbed moment of a permanent magnet synchronous motor position servo system, and the problem of velocity limit to uniform sliding mode control, a cascaded compound slide mode controller was proposed and designed for permanent magnet synchronous motor position servo system

    摘要針對某永磁同步電動機位置伺服系統負載力矩和轉動慣量變化大、干擾力矩強的特點，以及統一滑模變結構控制速度限幅的難題，提出並設計了串級復合滑模變結構拉制器。
  3. In chapter 3 the torque ripple minimization algorithm based on torque observation and instant torque control is studied as well as the fuzzy pid controller does

    在分析兩種轉矩脈動抑制方法局限性基礎上，研究了基於轉矩觀測的瞬時轉矩脈動抑制演算法以及轉速環的模糊pid控制器設計。
  4. Power - assist clutch amplifies torque for positive clutch engagement and acts as a back - torque limiter for smooth downshifts

    帶助力裝置的離合器起到了增強扭矩的作用，充分保證了離合器咬合效果，降檔時的感覺象有一個扭力回轉的限制器。
  5. In chapter 3, the control object of this subject, which is a three - link gymnastic robot on horizontal bar with limited joint torque and joint angle is brought forward and its mathematic model is developed. after simulating of the movement of the gymnasts, the control task of this subject is designed as a series swing - up and balance movement, the key point of control is analyzed

    第三章，提出本課題研究的對象：關節力矩和旋轉角度受限的三連桿單杠體操機器人，推導了它的數學模型；提出要完成的控制任務：模仿體操運動員上杠動作而設計的擺起倒立動作，分析了這套動作的控制關鍵。
  6. This thesis covers : first, description principle about locomotive, such as t four - phase rectifier and control theory, machine flux and torque models, the manner of controlling machine and so on

    如四象限變流器的原理和控制理論、電機磁鏈和轉矩模型、控制牽引電機的方案? ?直接轉矩控制理論等。
  7. In practice, outputs of motors are constrained by max torque, so do outputs of controller

    在實際應用中，電機輸出受到最大轉矩限制，則控制器的輸出也是受最大轉矩限制的。
  8. On account of the limited of the hardware circuit especially in the complicated and multiplex measurement, intelligent controls oriented instrument based on the qin ’ s model is developed to measure torque, rotating speed and power

    由於硬體電路的局限性，在大型多路測量中尤其突出，因此採用基於秦氏模型的智能控制項化虛擬儀器來實現轉矩功率的測試。
分享友人
分享到 Line

分享到臉書