通電輥 的英文怎麼說

中文拼音 [tōngdiàngǔn]
通電輥 英文
power application roll
  • 通 : 通量詞（用於動作）
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 輥 : 名詞[機械工程] （能滾動的圓柱形機件） roller
  • 通電 : 1 （通電流） set up an electric circuit; electrify; energize; be charged with electricity; power ...
  1. The driving rollers are electroplated with hard cr, tension self - controlling of winding - rollers are applied to the driving unit. the barrel of extruder, bullhead tee and die adopt cast aluminum heater which is endurable

    擠出機料筒三通和模頭均採用鑄鋁加熱，牽引輥筒電鍍硬鉻，輪鏈輪採用
  2. In view of this situation this article has conducted research to the design of metallurgy auxiliary biography with the frequency conversion table electrical machinery first multianalysis to the frequency changer and the frequency conversion table electrical machinery movement characteristic is carried out, the voltage waveform harmonious which the frequency changer outputs is big, attacks in a big way, and the voltage climbing rate reaches as high as 6600v / mu s which is 20 times ordinary sine alternating voltage, the rolling mill auxiliary biography table set the extremely strict request to the electrical machinery ; its movement frequency is very low, rate frequency in 8 - 20hz ; the velocity modulation scope is wide, the lowest movement frequency lowers to 1hz, and the starting number of times is quite frequently, each hour reaches as high as 600 - 800 time, the impact shoulders in a big way, the overload capacity request is high

    針對這一情況本文對冶金輔傳用變頻輥道電機的設計進行了系統研究。首先對變頻器和變頻輥道電機的運行特性進行詳細分析，變頻器輸出的電壓波形諧波大，沖擊大，電壓上升率高達6600v / s ，是普通正弦交流電壓的20倍;軋機輔傳輥道對電機提出了十分嚴格的要求:其運行頻率很低，額定頻率在8 - 20hz ;調速范圍寬，最低運行頻率低到0 . 5hz ，起動次數相當頻繁，每小時高達600 - 800次，沖擊負荷大，過載能力要求較高。
  3. On the base of the development of thick film pastes technology, ru - based thick film resistor pastes have been studied due to select conductive phase and inorganic binder. state - of - the - art techniques such as rolling, screen printing and sintering were used for sample preparation. effects of ingredients, printing parameters and sintering parameters, microstructure on the properties of thick film resistor ( trf ) have been analyzed with xrd, sem, dsc and electrical tests

    本文在跟蹤國內外厚膜漿料技術發展的基礎上，以釕酸鉍/銀系厚膜電阻漿料為研究對象，通過選用合適的功能相和無機粘結相成分，以三輥軋制、絲網印刷和高溫燒結等制備工藝為技術特徵，採用xrd 、 sem 、 dsc等分析方法和電性能測試手段，系統的研究了漿料中各相的成分配比、制備工藝參數，以及膜層微觀結構對厚膜電阻性能的影響規律。
  4. The paper introduces data processing methods in detail after providing the measuring circuit of roll profile. the system adopts vb to design softpanel of measurement system, realizing the serial communication between pc and singlechip base on mscomm control of vb

    本文在設計輥型檢測的硬體電路的基礎上，詳細介紹了數據處理的方法，採用vb語言設計測量系統的軟面板，並使用vb的mscomm控制項實現上位機與單片機的串列通信。
  5. By comparing with surface roughness and analyzing the surface of electrical discharge textured rolls with these parameters, it is proved that these parameters more concretely and exactly show the functional properties of surface topography

    通過與表面粗糙度的比較以及對電火花毛化軋輥表面形貌的分析，結果說明了表面形貌功能特徵參數使表面的承載性能和儲油性能分析更為具體和準確。
  6. We can realize the instrument control system and electric control system by using dcs and plc. the control system of reheating furnace is devided torol furnace area plc control system, roll plc control system and reheating furnace dcs control system. the controller of instrument and electric connect to the server of the operater station by the controlnet, by using dcs and plc, the technology of network and fieldbus technology to combine the process control system and process computer, intelligent instruments, drive system to realize the instrument and electric controll in one system

    採用dcs系統plc實現儀控和電控系統，把步進式加熱爐控制系統分為加熱爐爐區plc控制系統、加熱爐前後輥道plc控制系統、加熱爐dcs控制系統等三個子系統，儀表、電氣傳動用的控制器通過同一controlnet控制網與操作站的服務器連接，通過採用網路技術和現場總線技術，將控制系統與過程機、現場智能儀表和傳動設備連成一個整體，從而構成儀電一體控制系統。
  7. The platform is divided into three driving segments, adopting three speed - stepless motors to drive roller via wheel gear

    調速輸坯臺分3段傳動，採用3臺無級變速電機通過齒輪帶動輥棒。
  8. Furthermore, it exp1ains the reason of tolerance and how to overcome and reduce tolerance thxough the ana1ysis of a tree of the tolerance source of the electronic belt weighing conveyor. giving the example of the tolerance analysis of the electronic belt weighing conveyor with double idlers and levers - it brings forwfard the measures to improt - e the precision and stabi1ity, and the ideas of sery ' iceability and maintenanceability. as a result, the proposal of the new type electronic belt weighing conveyor is put forward

    接著，以電子皮帶秤的誤差源樹展開分析，說明各誤差產生的原因以及如何克服和減少誤差的方法，再具體通過對本公司生產的雙托輥雙杠桿電子皮帶秤進行誤差分析，得出了提高電子皮帶秤精度和長期穩定性的方法以及可維護性和可維修性的思想，進而提出了新型電子皮帶秤的方案。
分享友人
分享到 Line

分享到臉書