速度控制噴管 的英文怎麼說
中文拼音 [sùdùkòngzhìpēnguǎn]
速度控制噴管
英文
velocity-control jet- 速 : Ⅰ形容詞(迅速; 快) fast; rapid; quick; speedy Ⅱ名詞1 (速度) speed; velocity 2 (姓氏) a surna...
- 度 : 度動詞[書面語] (推測; 估計) surmise; estimate
- 控 : 動詞1 (告發;控告) accuse; charge 2 (控制) control; dominate 3 (使容器口兒朝下 讓裏面的液體慢...
- 制 : Ⅰ動詞1 (製造) make; manufacture 2 (擬訂; 規定) draw up; establish 3 (用強力約束; 限定; 管束...
- 噴 : 噴動詞1. (液體等受壓力而射出) spurt; spout; gush; jet 2. (噴灑) spray; sprinkle
- 管 : Ⅰ名詞1 (管子) pipe; tube 2 (吹奏的樂器) wind musical instrument 3 (形狀似管的電器件) valve;...
- 速度 : 1. [物理學] velocity; speed; blast; bat 2. [音樂] tempo3. (快慢的程度) speed; rate; pace; tempo
- 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
-
At the end of the experiment, we reconstructed the subsystem of second air measuring, i. e. we used airfoil measuring equipment as a replacement of original equipment of flute pipe. we also demarcated the velocities of spouts of burner which can deal with correlative data, and which can provide some help for operation
最後又對監測系統二次風測量子系統進行改造,將原笛型管裝置修復為機翼測風裝置,對傳感器進行差壓標定;在爐內噴口處標定速度,將數據進行處理,提供給熱工控制顯示用,對運行調整提供了幫助。Dilution and dispersion in constant horizontal flow and bottom multi - port discharging was studied in accordance with the hydraulic model test. the influence of diffusion parameters ( jet angle, jet velocity, number of nozzle, riser space ) and environmental parameters ( water depth, water velocity ) on dilution were analyzed. the experimental results show that environmental parameters have prominent effects on wastewater dilution and dispersion, in addition to that, diffuser design parameters have significant influence on wastewater dilution and dispersion. for bailonggang outfall zone, jet angel is 10 or so, nozzle number is 16 or so
藉助於人工模型試驗,分析了恆定橫流底部多孔排放時擴散器設計參數(射流角度、射流速度、噴口個數) 、上升管間距)及環境參數(環境水深、環境流速)對污水近區稀釋擴散效果的影響,實驗結果表明,除了環境條件對污水稀釋擴散效果影響明顯之外,擴散器設計參數對污水的近區稀釋擴散也有顯著的影響,針對白龍港排放口水域,噴口射流角度宜控制在10左右,噴口個數取16個The optimal parameters of making high silicon content aluminum alloys is : spray height is 220 - 230mm, spray angle is 30 ? the scanning velocity of atomizer is 30mm / s, the original offset of the substrate is 30mm, rotation velocity of the substrate is 120rpm, spray gas pressure is l. ompa, the diameter of the delivery tube is 3. 6mm, the drawing velocity of the substrate will be adjusted on - line with a plc on the basis of the spray
通過對多層噴射沉積原理及工藝參數的研究,得出制備al - 22si - 3cu - 1mg合金的最佳工藝參數為:噴射高度為220mm - 230mm ,基底轉速為120rpm ,霧化器掃描速度為30mm / s ,基底下降轉速依據噴射情況由智能控制器進行實時調整,噴射角度為30 ,初始偏心距為30mm ,導流管直徑為3 . 6mm ,霧化氣壓為1 . 0mpa 。This system captures the rack position signal and rotate speed signal of the fuel injection pump, and calculates the circulating fuel injection quantity by programming the computer. then the computer is programmed to control the daq board to generate a certain width pulse. finally, controlled by the pulse, the alcohol injection system injects a certain quantity alcohol into inlet manifold according to a setting diesel / alcohol proportion
該系統採用了在labview平臺上開發的pc總線?插卡式虛擬儀器系統,系統通過採集噴油泵的供油拉桿位置信號和轉速信號,利用計算機計算得出柴油的循環噴油量,再根據程序設定的柴油/酒精比例控制數據採集卡發出一定寬度的脈沖,控制低壓酒精噴射系統按比例將酒精噴入進氣歧管。分享友人