連測定向標 的英文怎麼說

中文拼音 [liáncèdìngxiàngbiāo]
連測定向標 英文
corner accessory
  • 連 : Ⅰ動詞1 （連接） link; join; connect 2 （連累） involve （in trouble）; implicate 3 [方言] （縫） ...
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 定 : Ⅰ形容詞1 （平靜; 穩定） calm; stable 2 （已經確定的; 不改變的） fixed; settled; established Ⅱ動詞...
  • 標 : Ⅰ名詞1 [書面語] （樹梢） treetop; the tip of a tree2 （枝節或表面） symptom; outside appearance; ...
  1. All the connected units in the page are detected by search algorithm of connected region. the row - column mergence of the character is defined by fuzzy connectedness of the connected units at four orientations. the combination of punctuation we adopt the method of combination behind recognition due to great effect of mergence

    版面圖文分割主要採用自底向上的辦法，利用連通域搜索演算法檢測出文本頁面上的所有連通基元，通過對連通基元的四個方向上的連接度進行模糊化處理來決定文字行、列的合併，並對在文字行合併時影響較大的標點符號採用先識別后合併的方法。
  2. After that, according to thermal conduction theories of anisotropic materials that were irradiated with continuously modulated laser, a photothermal measuring method about the thermal conductivity tensor and the orientation of the principal axis of the conductivity of arbitrarily opaquely anisotropic materials in the descartes coordinate axes was given by virtue of the theories of so ( 3 ) group rotation

    隨后又以在連續調制光輻照下的各向異性介質的熱傳導理論為基礎，通過so （ 3 ）群轉動理論，導出確定任意不透明各向異性介質在笛卡兒坐標下的熱導張量和熱導主軸方向的測量方法。
  3. An optimal protective measure was found, which is a mend to the standard link by retracing the converse detonator with a great extent and fixing the retraced nonel - tube with the detonator together to make the retraced part of nonel - tube smooth and bear little force of water stream

    經過分析比較和現場測試，找到最佳的拒爆防護方案，即在標準連接法的基礎上加以改進，將逆向連接的傳爆雷管折回的幅度增大，並將該打折的導爆管與雷管一起固定在網路的連接點上，使打折部位順滑而不受力。
  4. Construction of male sterility expression vector by integration of artificial sense and antisense cdnas of hsp70 into puc18 and puc19 respectively, we can obtain psc and pac. tapertal specific expression promoter ta29 and terminator nos are connected directionally with sense and antisense cdnas of hsp70 extrected and purified from psc and pac., then integrated into puc18 and puc19, by which we can build sense and antisense cdna nos ( respectively named plasmid 650 and plasmid 651 ) of ta29 - hsp70. for the sake of better screening and examination of transformed gene, we cut plasmid 650, plasmid 651 and 3301 ( containing gusgene bar screening marker gene ) with hindiii and ecor i enzymes, then connect purified fragments of 650and 651 with plasmid 3301 to construct the vector 3301 + 650 and 3301 + 651. corroboration of whether sense and antisense cdna - nos is integrated into plasmid3301 can be made by plate screening and enzye - cutting analysis

    分別將從psc 、 pac回收純化的hsp70正、反義cdna與絨氈層特異表達啟動子ta29及nos終止子定向連接，然後插入到puc18 、 puc19中，構建成花藥特異表達的ta29 - hsp70sensecdna - nos和ta29 - hsp70antisensecdna - nos ，分別稱作650和651質粒。為了更好地對轉化子進行篩選和檢測，用hind和ecor分別對650 、 651及3301質粒（含gus報告基因和bar篩選標記基因）進行酶切，將從650和651回收純化的目的片段與3301質粒進行連接，再對重組子進行平板篩選和酶切分析確定ta29 - hsp70sensecdna - nos和ta29 - hsp70antisensecdna - nos插入到3301質粒中，構建成3301 + 650和3301 + 651表達載體。
  5. An on - line minimum - variance estimator was developed for thrust acceleration applied to orbit transfer using discrete - time radar measurements. the mass - flow - rate of propellant was selected as a state variant, which was estimated by employing an integral state model and ekf filter. the variation equations for measurement vector to mass - flow - rate have been established to linearize the discrete - time measurement equations. the algorithm has applied successfully to maneuver process in commanding satellite into geo - stationary orbit. the results show that the algorithm developed here can monitor and determine whether engine works well or failure precisely and quickly during orbit transfer process

    飛行器軌道機動過程中，為跟蹤、定位機動目標和干預機動控制過程，需要統計處理離散的雷達觀測量實時估計推進發動機的推力，進而確定飛行器的瞬時軌道參數.本文所述演算法是該工程問題的探討和解決方案.文章建立了軌道機動過程中連續變質量運動模型和離散雷達量測模型，推進發動機的質量秒耗量作為表徵推力加速度的一個近似常量，應用擴展卡爾曼濾波對離散的雷達測量數據進行順序統計處理給出秒耗量的最小方差估計;文章詳細地推導了線性化量測模型的變分方程和觀測矩陣;模擬結果表明該演算法能快速、準確地估計推進發動機的質量秒耗量和向機動目標施加的實際推力
  6. Standard test method for determining the axial disassembly force of taper connections of modular prostheses

    測定模塊化假體錐形連接的軸向拆解力的標準試驗方法
分享友人
分享到 Line

分享到臉書