進水溫度 的英文怎麼說

中文拼音 [jìnshuǐwēndù]
進水溫度 英文
entering water temperature
  • 進 : 進構詞成分。
  • 水 : 名詞1 （由兩個氫原子和一個氧原子結合而成的液體） water 2 （河流） river 3 （指江、河、湖、海、洋...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 進水 : admission pipe
  • 溫度 : [物理學] temperature
  1. Automatic cip local cleaning system is specializd equipment used for automatic cleaning for beverage production line and filling facility. acid washing, alkali washing and thermal washing can be chosen. the tempera - ture for acid, alkali and hot water can be set

    自動ctp就地清洗系統，是用來對飲料生產線和灌裝設備進行自動清洗的專用設備；可提供酸洗，堿洗以及熱洗三個程序，設置酸液，堿液濃度及熱水溫度。
  2. 4. the temperature of infall cooling water is less than 30, the velocity of cooling water flow should be over 4l min for capacitor below 1000kvar and it should be over 6l min for capacitor over 1000 kvar

    4 .冷卻水的進水溫度不超過30 ，冷卻水的流速對1000kvar及以下的電容器不低於4l min ，對1000kvar以上的電容器不低於6l min 。
  3. For a soil or rock of water - lacked, a heat transfer theoretical model is developed, which is a steady or unsteady, the results show that reservoir temperature, thermal diffusion coefficient, inlet temperature, flow rate of and run time of ground source heat pumps have an effect directly on heat transfer process of dhe. it can deduce that intermit running is favorable for this type of soils and rocks

    對于貧含水地下巖土層建立了穩態與非穩態傳熱的理論模型，分析結果表明，巖土層的熱儲溫度、導溫系數、埋地換熱器進水溫度、流量以及地源熱泵系統的運行時間或開停機比，都對埋地換熱器的傳熱過程產生直接影響，可以推斷，對于該類型巖土層的地源熱泵系統，採用間歇運行將是有利的。
  4. Thermometer for fresh water inlet

    淡水進口溫度計
  5. Based on physical simulation and numerical simulation, the conversion of hot water slug flooding with nitrogen foam is presented and some injection indices are optimized, including foam concentration, gas - liquid ratio, injection rate, temperature of water, slug length. from reservoir research and oilfield development, studying disadvantageous factors, the paper will have guilding value for heavy oil reservoir development of leng 43 block

    對熱水+氮氣泡沫段塞驅的關鍵技術指標，包括泡沫劑濃度、氣液比、注入速度、注水溫度和段塞長度等重要參數進行了優選，提出了注水速度80 100t d 、氣液比1 ： 1 、注水溫度95 100 、溶劑濃度0 . 5的推薦方案。
  6. The forecast module uses the realtime data to calculate the forecast values. this thesis based on no. 3 blast furnace of the xiangtan iron and steel company. it match esthe hardware and software of the blast furnace

    在預測模塊中，用即時數據來計算預測值，並用調整系數進行調整，得到可靠的預測值，如鐵水溫度、理論燃燒溫度、直接還原度、焦比等。
  7. Thirdly, radiator performance test - bed thermal system control modeling and rule self - organizing fuzzy control simulation were studied. the water supply temperature, radiator inlet temperature, test room temperature based on water temperature regulation, air supply average temperature and test room temperature based on air temperature regulation total five controlled processes transfer function were set. finally, rule self - organizing fuzzy control simulation for two

    通過試驗，辨識了散熱器實驗臺熱工系統中供水溫度、散熱器進水溫度、基於熱水系統調節的測試室溫度、送風平均溫度及基於送風系統調節的測試室溫度共5個被控過程的傳遞函數，並對基於熱水系統調節和基於送風系統調節的測試室溫度響應過程進行了規則自組織模糊控制模擬。
  8. Because of the influences of the turbidity, ph of raw water, current, temperature and the pollutions of raw water, the process of coagulant dosage is a very complex reaction. to find out the automation of coagulant dosage and reduce the cost of the coagulant, many domestic and international scientific research organizations make research into the theory and mechanism of automation of coagulant dosage, such as the streaming current control method ( scd ), the emulation experimenting method in spot, mathematics model, flocculation control device ( fcd )

    由於受到原水濁度、 ph值、配水流量、原水溫度和其他水質污染的影響，投藥絮凝過程是一個非常復雜的反應過程，為實現投藥系統的自動化和降低混凝劑耗率，國內外相當多的科研機構和院校在進行投藥機理和自動化處理的研究，主要有流動電流儀檢測法（ scd ） 、現場模擬實驗法、數學模型、顯示絮凝控製法（ fcd法）等自動投藥方式的研究和實驗。
  9. By using the finite element numerical simulating method, and studies based on the practical project xiluodu arch dam, this paper studies systematically the type of joints, placing temperature, protection methods on the surface of concrete dams, the first stage artificial cooling method including different cooling water temperatures, cooling lasting days and cooling pipes arrangement

    本文利用數值模擬計算方法，以溪洛渡實際工程為依託，對大體積混凝土施工中常採用的溫控措施對混凝土溫度變化的影響規律進行了全面系統的研究，包括分縫分塊方式、澆築溫度、混凝土間歇時間、一期冷卻方式（包括不同進水溫度、不同水管布置、不同通水時間）等。
  10. Through developing a 2 - dimensions heat transfer model of buried pipe - in - pipe heat exchanger and simulating the process by computer, the author figures out inter - relations of factors which influence characteristics of buried pipe - in - pipe heat exchanger, such as pipe diameter, pipe length, ratio of pipe diameters, flow rate, inlet water temperature, patterns of water inlet and outlet, and material features made of pipe, and proposes some optimizing indexes of buried pipe - in - pipe heat exchanger. the author studies the " heat - - short circuit " phenomenon as well and gives < wp = 5 > some important results

    本文通過建立地下套管式埋管換熱器傳熱過程的二維傳熱模型，並藉助計算機對分析結果進行解析，弄清了影響埋管換熱器性能的管徑、管長、管徑比、通過流量、進水溫度、進出水方式以及管材等參數的作用，並提出了相應的優化指標，對研究界懸而未決的「熱短路」問題也進行了細致分析，得出了有關結論。
  11. Pilot - scale experimental results showed that, comparing to conventional gravity filtration, the up - flow filtration has greater capacity in containing removed suspended solid and producing filtrate under the test conditions. coarse media with particle diameter ranging 0. 63 - 2. 00mm were used in order to apply relatively higher backwash rate of 21 l / ( m2. s ) for achieving better media clean - up after a filtration run. under the test conditions, the media thickness ranging 82 - 85 iron, water temperature ranging 6 - 27, and influx turbidity of 30 ntu, it achieved the results of the average filtration rate ranging 16 - 18 m / h, the average effluent turbidity of 1 ntu, and action cycle ranging 14 - 24h

    中試研究結果表明，粗石英砂濾料上向流過濾比傳統的重力流過濾具有更大的含污能力和產水量，為適用較高的反沖洗強度（ 21l （ m ~ 2 ? s ） ）以便濾料清洗更干凈，採用粒徑范圍為0 . 63 2 . 00mm的粗石英砂濾料，濾層厚82 85cm ，水溫6 27 ，進水濁度為30ntu左右等情況下，能獲得平均濾速為16 18m h 、平均濾后水濁度為1ntu左右、周期達14 24小時的好效果。
  12. Two conclusions about the tube will be drawn : l ) being used in the heater of 300mw unit, it will cause 57 % decrease of the heater ' s volume and make the workshop ' s area much more smaller, which is gained from the reasonable device of the heater itself ; 2 ) when used in 100mw unit, higher capability lower temperature difference higher feed temperature of the heater will be available and better economic efficiency of the unit will be gained

    應用雙側微肋強化換熱管后體積可以減小為原來的43 ，大大減小了加熱器佔用廠房的面積。 （ 2 ）雙側微肋強化換熱管應用於100mw機組熱電廠加熱器時，進行改造中，由於原加熱器存在很多缺陷，使加熱器傳熱性能降低，此時使用雙側微肋強化換熱管對加熱器進行改造時，可以提高加熱器傳熱性能，減少加熱器端差，提高加熱器給水溫度，提高機組的經濟效益。
  13. The dehydration time is square of the droplets diameter so the small diameters of the droplets can cut down the drying time then reduce the height of the drying chamber. to the combined spin - flow pressure spray drying, the diameters of droplets are small and the dehydration rate is higher so keeping the qualities of the dried products we can increase the speed of the inlet wind and reduce the temperature of the outlet wind thus can improve the evaporation intensity of the drying chamber and the average energy utilization of the drying equipment

    因霧滴的脫水時間與其直徑的平方成正比，減小液滴直徑有利於縮短乾燥脫水時間，可有效降低乾燥塔的高度；由於旋流式組合壓力噴嘴霧化滴徑的減小，脫水速度明顯加快，在不影響乾燥物料性質的前提下，適當提高進風溫度，同時有效地降低排氣溫度，有利於提高幹燥塔的蒸發強度，也有利於提高幹燥設備的平均能源利用率。
  14. Nominal cooling capacity conditions : chilled water in 12, out7, cooling water in 30, out35

    冷量是依據冰水入口溫度12 ，出口溫度7 ;冷卻水進口溫度30 ，出口溫度35計算得出。
  15. At the same time, experimental study on boiling heat transfer by changing mass flow of refrigerant, mass flow of water, and inlet temperature of water was also finished. and then the performance of miniature evaporator was estimated

    本文完成了液單相、兩相熱平衡實驗和阻力特性實驗，研究了製冷劑在管內流動的壓降;同時進行了微型蒸發器流動沸騰實驗，通過改變製冷劑質量流量、水的質量流量、水的進口溫度等，實現了對微型蒸發器的性能評價。
  16. The experimental results showed that : in the summer operating mode, the refrigerating capacity and coefficient of performance of the system decreased with the increase of the temperature difference between supply and return ground - water and the water supply temperature ; in the winter operating mode, the refrigerating capacity and coefficient of performance of the system increased with the decrease of the temperature difference between supply and return ground - water and the increase of the water supply temperature. it also showed that, change the are of heat exchanger has great influence of refrigeration system

    本課題通過實驗測試井水進口溫度、進出口溫差以及在不同溫差下換熱器面積匹配對系統性能的影響。實驗結果表明，夏季工況下，隨著井水進口溫度的升高，進出口溫差的增大，系統製冷量減小，機組cop降低，系統運行性能惡化。冬季工況下，隨著井水進口溫度的升高，進出口溫差的減小，系統的制熱量增加，機組cop提高，系統運行性能優化。
  17. It is difficult to apply general pid control to temperature of secondary water of the heating power station with the indeterminate nonlinear and changing parameter characteristics by self - adjusting three parameters k _ ( p ) k _ ( j ) k _ ( d ) on line the fuzzy - pid controller has better response rate and stability property than the general pid controller

    常規的pid控制難以滿足供暖熱水溫度控制要求。據此，本文提出了採用模糊pid演算法實現對熱力站溫度的控制，利用模糊推理對pid參數k _ p 、 k _ i 、 k _ d進行在線整定。
  18. This experiment include many contents, in a word, that is summer condition experiment, winter condition experiment > summer - winter transition condition experiment and winter - summer transition condition experiment, furthermore summer condition experiment still include flux changing experiment and winter condition experiment still include thermal balance experiment this article dealt with the data of the test, calculating out energy absorbing ( energy discharging ) of buried pipe in winter condition ( summer condition ), input power of heat pump x heat exchanging of piece buried pipe length x co - efficiency performance ? op ( energy efficiency rate ? er ) and average heat exchanging coefficient ; in additiont this article compares the inlet water temperature and outlet water temperature of underground the first layer and the second layer buried pipe when heat pump was running, the results are that the heat exchanging ability of the second layer buried pipe outgos the first layer buried pipe, and heat exchanging is more stable ; and still analyse earth temperature resuming in the transition season. the results are earth temperature resume fast in the first week when the heat pump runs off

    本文測試內容相當多，概括地說就是四個工況的測試，即夏季製冷工況的測試、冬季供熱工況的測試、夏?冬過渡季測試和冬?夏過渡季測試；另外在夏季工況的測試中還進行了變流量測試，在冬季工況的測試中還進行了熱平衡測試。本文對測試數據進行了處理，計算出了冬（夏）季工況埋管吸（放）熱量、熱泵空調器供熱量（製冷量） 、熱泵空調器輸入功率、埋管單位管長換熱量、供熱性能系數（製冷能效比）和平均傳熱系數等；另外，還比較了熱泵運行時地下一二層埋管進出水溫度變化情形，得出地下二層埋管換熱能力優于地下一層埋管，且換熱很穩定；並分析了過渡季地下一二層埋管溫度恢復情形，得出熱泵系統停機一周內地溫恢復特別快。
  19. In winter, because the water temperature descend and the activity of microbial reduce

    冬季由於進水溫度的下降，微生物活性的降低，處理效果明顯下降。
  20. The main research contents are as follows : 1. build a steady - state simulation model of a general heat pump system, calculate system performances of using r22 and ( 30 / 70wt % ) r32 / r134a as refrigerants respectively, and get their performance curves as the working conditions change

    主要研究內容如下： 1建立了常規熱泵系統的穩態模擬模型，對採用r22和（ 30 70wt ） r32 r134a為製冷工質的系統分別進行了計算，得出其各自性能隨蒸發器進風或冷凝器進水溫度變化的關系。
分享友人
分享到 Line

分享到臉書