運算元自同態 的英文怎麼說
中文拼音 [yùnsuànyuánzìtóngtài]
運算元自同態
英文
operator endomorphism- 運 : Ⅰ動詞1 （物體位置不斷變化） move; revolve 2 （搬運; 運輸） carry; transport 3 （運用） use; wield...
- 算 : Ⅰ動詞1 （計算數目） calculate; reckon; compute; figure 2 （計算進去） include; count 3 （謀劃;計...
- 自 : Ⅰ代詞（自己） self; oneself; one s own Ⅱ副詞（自然;當然） certainly; of course; naturally; willin...
- 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
- 運算 : [數學] operation; arithmetic; operating
-
Second, the starting and stopping behaviors under disturbed condition are analyzed and calculated by using the dynamic concentrative parameter model, which gives some advice to better prescribe refrigeration system and set theoretic foundation for carrying out automatic control of refrigeration system. third, the normal running process is analyzed and calculated by means of rational matching theory, which gives some advice on how to better understand the parameter change under steady state and the affection of inlet - parameter on evaporator. fourth, the simulation software with dynamic characteristic is designed, which can be applied to calculate thernio - parameter of cryogen, air humidity and frost thickness under different initial and boundary conditions, and to carry out dynamic simulation under conditions of dryness, wetness and frostiness, at the same time, to achieve detection and simulation at any stage from starting to stopping
本文的主要內容如下： 1 ）對翅片管蒸發器結構特點進行分析，選取適當的微元控制體，就干、濕和霜工況下對每個微元分別進行傳熱傳質分析，基於經驗關系式確定霜的有關參數，對于霜工況下的霜生長建立模型，經適當假設，運用質量守恆、能量守恆和動量守恆方程建立適合動態模擬的蒸發器數學模型，為系統模擬奠定基礎； 2 ）對蒸發在大擾動下的開、停機過程，運用動態集中參數模型進行分析和計算，為更好地描述製冷系統運行的全過程奠定基礎，同時也為製冷系統實現自動控制提供一定的理論基礎； 3 ）對蒸發器正常運行過程，運用動態分佈參數和參數間定量耦合的觀點來分析和計算，為更好地了解穩態工況下各點參數的變化情況及各入口參數對蒸發器動態特性的影響即蒸發器性能對各參數變化的敏感性； 4 ）編寫翅片管蒸發器動態特性模擬計算程序，可以計算不同邊界條件和初始條件下的製冷劑熱力參數、空氣溫濕度和霜厚度分佈場，實現對翅片管蒸發器在干、濕和霜工況下的動態模擬。At the same time, based on weld pool image characters, a method for image processing is presented, in which gray - scale morphological operators is used to process weld pool images. by this method, the important geometrical parameters of weld pool are measured
同時結合實際的焊接自動化中熔池圖像的特點，詳細介紹如何利用灰度形態學，設計基於com的形態處理運算元，並且實時提取熔池的最大寬度、半長、後部面積、后拖腳等重要的幾何參數。The corresponding propositions will at the same time be given respectively. in section 3, the main task is to clarify the natural morphisms between toeplitz algebras
第三節的主要目的是對toeplitz運算元代數間自然的同態成為c ~ * -代數同態進行說明。
分享友人