過熱反應堆 的英文怎麼說
中文拼音 [guòrèfǎnyīngduī]
過熱反應堆
英文
superheat reactor- 過 : 過Ⅰ動詞[口語] (超越) go beyond the limit; undue; excessiveⅡ名詞(姓氏) a surname
- 反 : Ⅰ名詞1 (方向相背) reverse side 2 (造反) rebellion 3 (指反革命、反動派) counterrevolutionari...
- 應 : 應動詞1 (回答) answer; respond to; echo 2 (滿足要求) comply with; grant 3 (順應; 適應) suit...
- 堆 : Ⅰ動詞(堆積) pile up; heap up; stack Ⅱ名詞1 (堆積成的東西) heap; pile; stack 2 (小山 多用於地...
-
Bonus boling nuclear superheat reactor
沸騰式過熱核反應堆Boiling nuclear superheat reactor
核過熱沸騰反應堆The forming - nucleus drive power could form numerous little crystal nucleus under natural melting temperature. the formation of tic particles in the melt could be divided into two phases which was forming - nucleus and growth. the forming mechanism of tic was : melting ti first surrounded c, then ti melting in the alloy and c formed a complicated reaction mesosphere on the carbon surface
根據熱力學及動力學分析,認為在碳顆粒界面處tic的形核率很高,形核驅動力足以在正常的熔煉溫度下形成眾多的小晶核;熔體中tic顆粒的合成可分為形核與長大兩個階段,其形核機制為:首先活性ti原子包圍c ,溶入合金中的ti與c在碳表面形成一復雜反應中間層,隨著反應進行, ti和c顆粒不斷減少,生成的tic不斷彌散分佈於熔體中;其長大過程伴隨著tic顆粒的相互堆砌、聚集和形態規則化。Changing the grading of sic particles not only affects the strength and pile density, but also modifies the phase compositions and microstructure of the material. with the reducing of sic particles, the strength of the material increases obviously. the nitrification scheme has the greatest influence on phase compositions and microstructure " of si3n4 ( si2on2 ) - sic, after two continuous nitrification reacting peak and short - time high - temperature treating, the best properties can be obtained ; and the residual strength of the composite is much higher after the thermal shock resistance test, which shows that the material possesses excellent thermal shock resistance
本論文較全面地探討促進強度和顯微結構良好的si _ 3n _ 4 ( si _ 2on _ 2 )結合相的實驗條件,實驗數據顯示:引入適量的燒結助劑能夠促進si _ 3n _ 4 ( si _ 2on _ 2 )的生成和晶粒的長大,而過量時,其促進作用反而下降;隨著si粉加入量增加,生成的結合相明顯增多,復合材料的性能顯著提高;改變sic顆粒級配不僅影響復合材料的強度與堆積密度,而且對復合材料的物相與顯微結構也有影響,隨著顆粒逐漸細化,材料的強度有較大的提高;對復合材料的強度、物相與顯微結構影響最大的是氮化制度,經過兩個氮化高峰連續的反應和短時間的高溫后處理得到的復合材料性能最好;通過抗熱震性能實驗后復合材料的殘余強度較高,顯示出較好的抗熱震性能。Obviously, it is very helpful to prevent first side outline from overpressure and overheating through the way of discharging the heat generated by cooling system ; and prevent the core of the reactor from being too cooled by limiting the discharge amount of steam
這有助於:一通過排出反應堆冷卻系統產生的能量來防止一迴路側超壓和過熱;二通過限制蒸汽向大氣的釋放量來防止反應堆堆芯過冷。分享友人