過腹板 的英文怎麼說

中文拼音 [guòfùbǎn]
過腹板 英文
side web
  • 過 : 過Ⅰ動詞[口語] （超越） go beyond the limit; undue; excessiveⅡ名詞（姓氏） a surname
  • 腹 : 名詞1 （軀乾的一部分） abdomen; belly; stomach 2 （鼎、瓶子等器物的中空而凸出處） empty and protr...
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  1. The forces that developed from the deformation in the cross-frame were primarily transmitted from the connection plate into the web by the upper pair of intermittent fillet welds.

    因橫向框架中的變形所發生的力最初由連接板通過較上面的一對間斷貼角縫傳入腹板中。
  2. In light of the elastic thin plate theory, the author induced equilibrium differential equation of bi - direction cellular slab, which was proved correct through analysis and comparison to result of ansys to with theoretical calculation. through the deflection and bending moment coefficient calculation of bi - direction cellular slab under various boundary conditions, the author brought forward the theory that the deflection of mid - span and bending moment coefficient calculation of mid - span and support of bi - direction cellular slab could be in accordance with solid plates ", which could satisfy the precision of engineering

    本文根據彈性薄板理論，導出了雙向空腹板的平衡微分方程，並通過理論計算和通用有限元程序ansys結果對比，驗證了其正確性；通過對各類邊界條件下雙向空腹板撓度和彎矩系數的計算比較，本文提出：雙向空腹板跨中撓度及跨中、支座彎矩可使用本文空腹板剛度公式查找現有的實心板撓度彎矩系數表進行計算，完全能滿足工程精度要求。
  3. The investigation of this paper has grate actual and expansive significance and offer methods for the application of rigid frame. the investigation indicate that the ripple web plate ' s critical stress has great improvement than ordinary flat plate and ripple web plate variable cross - section has a rather superiority than constant cross - section portal rigid frame

    本論文所做的研究工作具有很強的現實意義和推廣意義，為門式剛架的應用提供了思路。通過研究表明：波紋腹板的臨界應力比普通的平板有很大提高，而波紋腹板變截面門式剛架與等截面門式剛架進行對比也有較大的優越性。
  4. Modeling the general solid web continuous box girder and opening - in - web ( open web ) continuous box girder by ansys finite element modeling tool, node stress of governing section and corresponding shear lag values are analyzed. the solution is validated by comparing with variational results and modeling test values. based on the model, the section shear lag induced by dead load, prestress tendons and car loads under the most unfavorable condition and lateral symmetry are also approached. the influence of shear lag effect in double - level continuous box girder is considered with opening - in - web and the web location. the analysis indicates that double - level - load arouses less shear lag effect than one - level - load. when self - weight and prestressed tendons act on together, the shear lag effect on box girder take on a evidently change

    基於所建立的有限元模型，本文分別對實腹和腹板開孔兩種箱梁在恆載、車載、預應力荷載作用時，各主要截面的剪力滯效應進行分析，通過施加縱向最不利的和橫向對稱的車輛荷載，研究實腹連續箱梁和空腹連續箱梁在承受雙層荷載和單層荷載時引起的剪力滯效應，並考慮腹板開孔及開孔位置對于連續箱梁剪力滯效應的影響。分析表明，雙層車載對于箱梁引起的剪力滯系數比單層車載的影響要小，對于箱梁中存在引起的剪力滯后現象有一定的改善作用。
  5. Several kind of simplified calculating models are introduced. the web and flange plates in mcar with a large number of corrugations were equivalent to orthotropic curve plates. the equivalent elastic modulus was yielded by tensile tests, which provides the material constants data for the structural static and dynamic analysis

    2 、綜述了拱型波紋鋼屋蓋的各種簡化計算模型，並把帶有波紋的腹板和底板分別等效成正交各向異性平曲板，通過拉伸測試了它們的等效彈性模量，為結構的靜力和動力有限元分析提供材料常數依據。
  6. In this paper, 130mm diameter hot - rolled bars ( 3 transus temperature is 798 c ) were used in experiments. the superplastic property of ti - 1023 alloy was studied systematically by the experiments of tensile and compression. the preparation method of fine - crystalline structure and the processing parameters of superplastic forging are optimized

    本文以130mm熱軋棒材為原材料，通過超塑性拉伸和超塑性壓縮試驗，對ti - 1023合金的超塑性進行系統研究，研究坯料細晶組織制備方法，優化超塑成形工藝參數，為高筋薄腹板復雜形狀ti - 1023合金鍛件超塑性等溫模鍛工藝的制定提供試驗依據。
  7. 20 src eccentric loading specimens were designed taking the relative eccentricity e0 / h the slendemess ratio 10 / h as the factors. according to the mechanical behavior of eccentric loading columns, unidirectional embedded electronic steel - concrete slip transfers and double - directional embedded electronic steel - concrete slip transfers were respectively placed inside these 20 specimens and electronic strain gauges were also installed on the steel shape flanges webs and concrete. the change of the mechanical behavior and interior slip of the 20 specimens in the whole process of loading was fully observed

    設計了以長細比、偏心距為主要參數的20個偏壓柱試件，根據偏壓柱的受力特性，在試件中分別放置了單向內置式鋼?混凝土電子滑移傳感器和雙向內置式鋼?混凝土電子滑移傳感器，並分別在型鋼翼緣、腹板和混凝土上布置了電子應變片，對試驗柱在受荷全過程的受力性能、和內部滑移的變化進行了細致的觀察。
  8. ( 4 ) by the value pu of simply supported plate comparing with the pu of rectangular tube, the regulations are found between the interaction for the post buckling plates of rectangular tube and the flange - web width ratio bf / bw, as well as bf / t, bw / t, considering interaction of plates are also obtained

    （ 4 ）本文通過對矩形鋼管考慮和不考慮板組相關影響承載力的比較，得出了屈曲后矩形鋼管板組相關作用與翼緣、腹板寬度比b _ f / b _ w的關系，同時也得出板組相關性與板件寬厚比b _ f / t 、 b _ w / t的關系及規律。
  9. In this paper, a two - dimensional analysis of the tanjialiangzi bridge was first performed ; then a segment of the bridge was modeled and a three - dimensional analysis of it were carried out by employing the fem software of ansys ; after a careful analysis of the result of the calculations, the causes of the diagonal cracking in the web of the beam were given out ; and also, in the last part, common steps of damage evaluation of the long - span pc continuous bridges through fem software were summarized

    本文首先對譚家梁子大橋作平面計算分析；然後運用ansys軟體建立該橋局部梁段的空間有限元模型，並在此基礎上進行空間局部有限元分析；通過對計算結果的整理和分析，從設計方面探討了該橋腹板斜裂縫產生的原因：此後，針對病害成因，本文提出了裂縫修補和腹板加固的方法；最後總結了運用有限元軟體分析同類橋梁病害的一般方法。
  10. 2 based on experimental results and finite elements analysis of new joint, the stress transfer mechanism of the new joint is analyzed. there are two stress transfer patterns about the new joint, one is for rectangular steel tubular column joint, its stress transfer pattern is that beam moment is transferred to column webs mainly by stiffeners, the other is for crft column joint, its stress transfer pattern is that part of beam moment is transferred from stiffeners to column webs, another part of beam moment is transferred to infilled concrete by column flange

    （二）基於新型節點的試驗結果和有限元分析，研究了新型節點的傳力機理，其應力的傳遞路徑分為兩種：對于鋼管柱節點，梁端彎矩主要通過加勁肋板直接傳至柱腹板，對于鋼管混凝土柱節點，梁端彎矩一部分通過加勁肋傳給柱腹板，另一部分通過柱翼緣傳給鋼管內的混凝土。
  11. After comparing between the finite - element analysis and experimental results, the author verified the fem. then according to the chinese code, the nonlinear finite model of the beam - to - column is established which are made of different size components. the responses of beam - to - column web moment connections which are made of different size components are compared and analyzed from three facets, and the conclusions about the joints behavior are drawn : thicken the connection plate, lengthen the connection plate or use a back - up stiffer can improve the connection behavior, consist of improving the behavior of load - supported and reducing the stress convergence in the flange moment plates

    本文根據我國規范的有關規定，自行建立了12個不同構件尺寸的樑柱腹板連接的三維有限元模型，對不同構件尺寸的樑柱腹板剛性連接節點在單向荷載作用下的反應進行了研究，從結構的mises應力等值線示意圖、梁端加載處的荷載? ?位移曲線、翼緣連接板兩端的mises等效應力以及翼緣連接板與柱相連接的三邊的mises應力等值線示意圖四方面進行了比較與分析，從而得出了不同構件尺寸的樑柱腹板剛性連接的在受力行為上的結論：增加翼緣連接板的厚度、增加翼緣連接板的長度以及採用柱的橫向加勁肋均可以改善節點的受力性能：提高節點的承載能力；減小翼緣連接板內部與柱翼緣邊的的應力不均勻現象，從而避免試件過早地發生破壞。
  12. Second, change the diaphragm ’ s space between, retain the other thing, analyze the influence of the stress and deformation of box ? girder cross section and the beam web. based on the analysis upwards, the writer studied the rule of the influence of the stress and deformation box ? girder cross section and the beam web with different diaphragm ’ s space between. according to the results of finite element analysis, the writer puts forward some suggestions which will provide some reference for the following design

    本文利用ansys有限元分析程序，對指定斷面，不同曲率的曲箱梁，建立完備的有限元模型，分別對二個方面的問題進行了分析:其一，通過對箱梁在有無跨中橫隔板時截面頂板及腹板的變形和應力分佈的對比分析，闡述了設置跨中橫隔板的重要性;其二，在相同工況下，通過改變橫隔板的設置間距，分析對箱梁翼緣及腹板的受力影響。
  13. By simulating body node with fea software ansys and comparing its results with the experiment ones, natural capacity of semi - rigid connection node itself was discussed, and the experimental results were analyzed additionally, and the bearing conditions of sections which could n ' t be tested in experiment were obtained, as well as two kinds of bearing conditions under different conditions that the connections with and without stiffener were compared in detail

    在討論半剛性連接節點本身的性能時，通過有限元軟體ansys對節點進行三維非線性有限元精細模擬，將計算結果與試驗所得數據對比，對試驗結果進行補充分析，了解沒有測到試驗數據的節點組件在加載過程中的受力情況，並對帶雙腹板角鋼頂、底角鋼連接在有無加勁肋兩種情況下的受力狀態進行詳細對比。
  14. Through the theoretical calculation and parameter analysis and compared the result with general composite beam, the results show that the section stress redistributed by the effects of concrete shrinkage and creep and tensile stress by difference temperature will be greatly reduced. the forcing characteristic of this

    通過理論計算和有限元參數分析，與常規組合結構進行對比，驗證了預應力波形腹板組合結構具有大大減小徐變引起的應力重分佈及溫差和收縮效應在混凝土板產生的拉應力值、對加載齡期和持荷齡期不敏感的特點，結構受力性能非常優越。
  15. The national steel structure design code ( gbj17 - 88 ) is not permitted the b / t exceed ( 10 + 0. 1 ) 235 / fy. the width - thickness ratio of the web ( b / t for short ) exceed the limitation often

    鋼結構設計規范（ gbj17 - 88 ）規定t形截面軸壓構件腹板寬厚比不應超過（ 10 + 0 . 1 ） ，按國家標準生產的t型鋼的腹板寬厚比大多超過限值。
  16. ( 2 ) with the universal finite element software ansys, reasonable finite models for such slab - column connection were established and a static non - linear analysis was made, and the rule of this structure about the aspects of force deformation and destruction under vertical load and unbalanced bend are summarized. based on this, a simplified calculation method of punching capacity is advanced

    研究空腹板柱節點的傳力機理和破壞模式;對在豎向荷載作用下、豎向荷載和不平衡彎矩共同作用下板柱節點內力、變形和破壞過程進行研究，並提出了抗沖切承載力的簡化計算方法。
  17. In this paper, the best reinforcement scheme, which was found by nerve network and genetic algorithm from serval reinforcement schemes, was applied to strengthen a prestressed concrete continuous rigid fame bridge with many quanlity faults, such as excess fall deflection of the main span deck > serious web slop crack existing between main pier abutment and one fourth span, and very poor mud jacking quanlity in the prestressing tendon tubs

    本文針對某預應力混凝土連續剛構橋所存在的實際問題：如主橋橋面下撓度過大；主墩和四分之一跨徑處均存在較嚴重的腹板斜裂縫；預應力管道壓漿質量較差等。提出了幾種加固方案，並用神經網路和遺傳演算法進一步優化出了較佳的加固方案，進行了加固前後效果對比分析。
  18. ( 4 ) two component anchor bolt and dowel are afforded, a formulas to calculate the punching capacity of this slab - column connection with the effect of punching component is given in the article. comparing with other kinds, the two punching component is effective. ( 5 ) the possible destroy patterns of this slab - column system are discussed in the text, and design principle and step in detail about slab - column connection are

    （ 4 ）提出抗沖切錨栓和銷釘兩種新型抗沖切元件，給出配置抗沖切元件時板柱節點的承載力計算公式;通過比較表明，這兩種新型抗沖切元件對薄壁箱體現澆混凝土空腹板來說是有效的。
  19. With combined effort in theoretical analysis and fem, the author studied engineering mechanism and distortion character, under vertical load, of rc bi - direction cellular slab, and put forward some ideas on construction design and practical formulations

    本文通過理論分析和有限元方法相結合，研究了鋼筋混凝土雙向空腹板在豎向荷載作用下的受力機理和變形特徵，並提出了一些設計建議和實用公式。
  20. Theory analysis in this paper pointed out that the flexural - torsional buckling is the usual form of t - section steel. so the slenderness ratio of flexural - torsional buckling should be used when people give out the b / t ratio by the " equal stability " conception. initial stress, defects and tangent modulus are include in the deduce of the paper to get a rational b / t ratio

    通過理論分析指出軸心受力剖分t型鋼整體失穩以彎扭屈曲為主，所以在運用「等穩定」方法確定腹板寬厚比限值時應與桿件的扭轉長細比「掛鉤」 ，並以此為出發點考慮殘余應力、初始缺陷，應用切線模量推導出了較為合理的腹板寬厚比限值公式。
分享友人
分享到 Line

分享到臉書