配復筋的 的英文怎麼說

中文拼音 [pèifùjīnde]
配復筋的 英文
doubly-reinforced
  • 配 : Ⅰ動詞1 （兩性結合） join in marriage 2 （使動物交配） mate （animals） 3 （按適當的標準或比例加以...
  • 復 : Ⅰ形容詞1 （重復） repeated; double; duplicate 2 （繁復） complex; compound Ⅱ動詞1 （轉過去或轉過...
  • 筋 : 名詞1 （肌的舊稱） muscle2 [口語] （肌腱或骨頭的韌帶） tendon; sinew 3 [口語] （可以看見的皮下靜...
  • 的 : 4次方是 The fourth power of 2 is direction
  1. Based on the numerical simulation and accuracy analysis to previous slab ' s test with the ansys program, the study of composite wall, with various detail design under potential load action respectively or jointly is carried on and the wall ' s atress behavior and failure mode is obtained, also the influence to wall ' s stiffness and bearing capacity by kinds of factors, including wall ' s shear span ratio, member ' s section, bar arrangement, etc. based on the hammer blow test and stiffness test, a 1 / 3 scale ten - bay model ' s modality parameter and elastic deformation characteristic is analyzed

    在對密肋復合墻板運用ansys ~ （ （ ? ） ）程序進行數值模擬、分析驗證的基礎上，對典型組合墻體在不同連接構造和不同荷載效應組合作用下的受力形態和破壞模式進行研究；計算分析了復合墻體剪跨比、邊框柱截面尺寸、邊框柱配筋大小以及墻板內肋梁肋柱配筋等諸多因素對密肋復合墻體承載力及剛度的影響，得出其變化規律。
  2. In the design, the construction measures such as application of shrinkage - compensating concrete, arrangement of spacing layer between the foundation rock and the bottom slab, adding outside waterproof layer, flexible connection between outlet pipe with side - wall, integerated concrete placement of pump seat with bottom slab and design of reinforcement with application of advanced calculation theory are used according to the characteristics of lager span, larger volume and complex loading conditions of the understructure

    針對下部結構跨度大、體積大、受力復雜的特點，在設計中採取多種措施，包括採用補償收縮混凝土、基巖與底板間設隔離層、增設外防水層、出水管與邊墻採用柔性連接、機座與底板整體澆注、採用先進計算理論指導配筋。
  3. This paper is focused on a series of experiments including two kinds of large - scale composite walls with different joint fashion under low cyclic loadings. the experiments are carried out in order to know the seismic of composite walls out - of - plane and research the impact of deformation out - of - plane on carrying ability in - plane, experimental design reference is expected to achieve and tech support provide

    為了彌補這方面的研究不足，本文對兩種連接方式足尺復合墻片進行了低周反復荷載作用下的恢復力試驗，以了解配筋砌塊復合墻的平面外抗震性能，同時研究平面外變形對墻體平面內抗震性能的影響，為配筋砌塊復合墻的設計提供依據。
  4. The influences of different reinforcement style of the concealed bracings and different span - height ratio of lintel beams on bearing capacity, stiffness and deterioration process, ductility, hysteresity capacity, energy dissipation and failure features of coupled shear wall were studied through experiment of 7 specimens under low cyclic loading

    通過7個結構試件在低周反復荷載作用下的試驗，研究了不同暗支撐配筋形式、不同連梁跨高比對雙肢剪力墻的承載力、剛度及其衰減過程、延性、滯回特性、耗能、破壞特徵等方面的影響。
  5. The scc has the following advantages : remarkably reducing the noisy pollution and the worker s labor intensity in construction, deducing the rough surface or segregation because of missing - vibration or excessive - vibration in conventional construction, resolving the quality - defect problems resulting from lacking - vibration in the section of complex shapes and densely - packed reinforcement area. at the same time, large of industrial solid waste such as fly ash and blast furnace slag is utilized in the proportioning of scc. it is helpful in comprehensive utilization of resource and environment protection, so the scc belongs to " green concrete ", it is a branch of hpc which will be developed in the future

    這種混凝土可以顯著降低混凝土施工中的噪音污染；大幅度減輕工人的勞動強度；減少傳統混凝土施工中因漏振或過振造成的麻面或離析；解決了配筋密集、結構復雜部位因振搗不足而造成的質量缺陷問題；同時，由於自密實混凝土在配製中，大量利用粉煤灰、高爐礦渣等工業固體廢棄物，有利於資源的綜合利用和生態環境的保護；從而被譽為「綠色混凝土」 ，是未來混凝土向高性能發展的方向之一。
  6. Tow speciments of prestressed fabricated beam - column subassembly were tested under reversed cyclic loading. experimental studies were carried out to investigate the strain distribution, failure mechanism and load - bearing capacity on the beam - column connections, as well as ductility, hysteresis curves energy dissipation, displacement restoring capacity of full pc speciments

    本文通過兩榀預壓裝配式樑柱組合體在低周反復荷載下的試驗，了解了預壓裝配式框架梁端截面應變分佈、破壞機理和極限承載能力；探討了全預應力配筋截面延性特徵、滯回性能、耗能能力和變形恢復能力。
  7. Basing the analysis on the experimental data, the author provides the load - bearing capacity formula of the concrete short column confined by overlapping hoops under uniaxial compression and the relationship between characteristic value of hoop and spacing of hoop, which is of great practical value

    摘要通過實驗數據的分析，提出了軸心受壓復合方箍短柱正截面承載力的計算公式並給出了配箍特徵值與箍筋間距的關系，具有一定的實用價值。
  8. Based on analysis and comparison of existing test data applied to existing ultimate strength prediction models, interfacial stress at the end of plate is deduced. after formulas for calculating the effective moment of inertia for frp - strengthened beams being revised and adjustment coefficient related to nominal main steel reinforcement ratio and curtailment length ratio being put forward, strength prediction formulas of compound beams under plate end debonding failure are established. in analysis of strength of compound beams under intermediate crack induced interfacial debonding failure mode, several bond strengths and their relation are introduced

    對于板端剝離破壞，在總結現有承載力模型的基礎上，利用已有試驗數據對各承載力計算公式進行了分析比較，進一步採用分階段分析法，推導了板端界面應力的計算公式，在此基礎上，採用加固復合梁有效慣性矩的修正公式，建立了考慮名義配筋率和板端偏移比影響的板端剝離破壞梁承載力的計算公式；對于跨中受彎裂縫導致的粘結破壞，闡述了常見的幾種粘結強度之間的區別和聯系，並基於拉剪粘結強度，提出了跨中受彎裂縫導致粘結破壞的承載力計算公式，並利用現有試驗結果確定了模型中的一些參數；最後，利用試驗數據對本文建立的兩種粘結破壞承載力計算公式進行了檢驗，結果基本吻合。
  9. Then the coupling beams with new reinforcement layout were made an inquiry into, and the improvement on the seismic behavior by coupling beams diagonally reinforced with a few rows in end regions was found out at last, based on the observations of the experimental phenomena and the analysis of the measurement result, and by the comparison of seismic behavior by making use of hysteretic response, ductility and energy dissipation behavior, a conclusion is presented : the code for design and construction of reinforced concrete high - rise structures ( the draft asked for advise hi 2000 ) ca n ' t ensure that the coupling beams have fairly good seismic ductility ; the result of improvement of the seismic ductility of the coupling beams by the increase hi stirrups besides the strengthen of longitudinal detailing reinforcement was n ' t obvious ; the coupling beams diagonally reinforced with a few rows in end regions have fairly good mechanisms, and the ductility and the behavior of energy dissipation are better than conventionally reinforced concrete coupling beams, so it is suitable to te tised in short coupling beams

    本文通過對三根小跨高比（均為l h = 1 . 0 ）剪力墻洞口連系梁在低周反復荷載作用下的試驗，了解了嚴格按《鋼筋混凝土高層建築結構設計與施工規程》 （ 2000年徵求意見稿）設計的連梁具有的抗震性能，研究了採取增大連梁配箍量同時加強縱向構造筋的方案對抗震性能的影響，並進一步對新的配筋形式的連梁進行了探討，了解了在連梁梁端配置多排交叉斜筋方案對連梁抗震性能的改善。通過對試驗現象的觀察和量測結果的分析，利用荷載?位移滯回曲線、延性和耗能性能等指標對各個試件的抗震性能進行了比較，最後得出結論： 《鋼筋混凝土高層建築結構設計與施工規程》 （ 2000年徵求意見稿）不能保證小跨高比連梁具有較好的抗震延性：通過增大連梁配箍量同時加強縱向構造筋的方案對改善連梁的抗震延性的效果不太明顯；梁端配置多排交叉斜筋的連梁具有相對較好的受力性能，其延性和耗能性能等各項性能指標均優于普通配筋連梁，宜在深連梁中採用。
  10. The tendons of unbounded ppc have smaller fraction force and are easier to bend to many shapes, so it is more suited for building these rooms whose span are large

    無粘結預應力筋摩擦力小，且易彎曲成各種形狀，特別適合建造需用復雜的連續曲線配筋的大跨度樓蓋和屋蓋。
  11. By changing the parameters of stirrups ratio and axial load ratio, 6 high strength concrete ( hsc ) columns are tested subjected to cyclic lateral load. the baring capacity of hsc columns with new form of stirrups are compared with hsc columns with normal form of stirrups. load - displace relation curves are obtained

    本文以體積配箍率和軸壓比為主要控制參數，對不同配筋模式的6根高強混凝土壓彎構件進行了低周水平反復加載試驗，得到了箍筋約束混凝土的荷載?位移滯回曲線。
  12. The idiographic contents are listed as follows : 1 ) through the tests of the anchorage performances of steel column bases of 1 / 5 scale under uniaxial reversed loads, the tested ultimate loads, ductility, stiffness and reasonable modes of reinforcement design of two specimens are presented in this thesis

    本文主要工作: 1 .進行了兩個1 / 5縮尺的鋼筋混凝土承臺-鋼柱腳試件單向重復加載下的錨固性能試驗研究，對試件的錨固承載力、延性、剛度以及合理配筋型式等進行了研究。
  13. The influences of the reinforcement proportion of distributing bars to concealed bracings on bearing capacity, stiffness, deterioration process of stiffness, ductility, hysteresity capacity, energy dissipation and failure features of low - rise shear wall were studied through experiment analysis on 6 models of low - rise shear wall with concealed bracings under cyclic loading

    通過6個帶暗支撐低矮剪力墻試件在低周反復荷載作用下的試驗分析，研究了不同的分佈鋼筋和暗支撐鋼筋配筋比例對低矮剪力墻承載力、剛度及其衰減過程、延性、滯回特性、耗能、破壞特徵等方面的影響。
  14. Abstract : optimum design of individual foundation considering the effect of strength and deformation is discussed in this paper. the optimal mathematical model of determining the bottom surface demention of individual foundation under eccentric load is derived. the optimal solution is decided by method of optimization and the method we select is penalty fonction and complex method. the program of optimum algorithm is comiled and design and drawing of individual foundation is completed. the final results of engineering samples suggest that the cost of material and engineering amount can reduce approximatly 5 % - 6 %. a fair - sized economic efficiency can be received by using optimum method to design foundation

    文摘:筆者討論了獨立基礎在考慮強度和變形條件下的優化設計.導出了確定獨立基礎底面尺寸的優化數學模型，導出了偏心荷載作用下基礎的高度和底面配筋的計算公式，求解優化解採用最優化方法的復合形法和罰函數法.通過基礎實例和工程實例的計算表明優化設計可以節省材料和工程量5 16 .所以將本文優化方法用於基礎設計，會產生較大的經濟效益
  15. A simplified formula for the shear capacity of rc simply supported beam which strengthened with the cmmr is proposed in this paper. 3 、 the shear capacity of rc beam strengthened with cmmr is studied. though the test of fourteen simply supported reinforced concrete beams and five overhanging reinforced concrete beams with cmmr, it analyses the effects of shear - span ratio, web reinforcement ratio of cmmr, style of loading, preloading on strengthening, and compares them with rc beams using ordinary stirrup

    3 、根據本文進行了的14根混凝土簡支梁和5根混凝土伸臂梁的水泥復合砂漿鋼筋網抗剪加固試驗，分析了剪跨比、鋼筋網配筋率、加固形式以及持荷狀態等因數對整個構件極限抗剪承載力的影響，並與混凝土梁進行了比較。
  16. On the basis of the traditional elasticity theory, nonlinear theory, ultimate theory and theory of reinforced concrete slabs with simple - supported condition, this paper analyzes the whole process of reinforced concrete thin slabs in the loading test of distributing static load, on the objects of reinforced concrete thin slabs with complex geometry, complex boundary condition and distributing of reinforce bars. and then analyzes the load capacity under the effecting of static load

    本文在傳統的鋼筋混凝土彈性理論、非線性理論和極限理論以及在簡單支承條件下的鋼筋混凝土板理論的基礎上，以復雜幾何形狀、邊界條件及配筋形式的鋼筋混凝土薄板為研究對象，對其在靜力分配梁加載下的加荷試驗的全過程進行分析，並對其在靜荷作用下的受力性能進行分析。
  17. A seismic shear capacity equation for ductility and non - ductility columns is proposed to amount for the reduced shear contribution of concrete as to the increasing of displacement ductility levels. 6. the behavior of columns * transverse displacement within yield hinge regions is also discussed based on truss - arch model. 7. the seismic shear capacity design equation of columns with various ductility levels is proposed in statistic method on the basis of test data collected from japan and china to simplify the equation resulted from truss - arch model

    對國內外試驗資料進行了統計分析，詳細分析了剪跨比、軸壓比及配箍特徵值對框架柱構件抗剪承載力的影響，得到了反復荷載下框架柱塑性鉸區域極限承載力計算的統計公式；在理論推導公式及統計公式的基礎上，參考國內外規范，首次管品武；鋼筋混凝土框架柱塑性鉸區抗剪承載力試驗研究及機理分析提出了鋼筋混凝土框架柱塑性鉸區域剪切承載力抗震延性設計實用公式。
  18. In recent years, during the detection of the established reinforced concrete or the prestressed concrete box girder bridges etc. the large structures, we can find that the concrete in particular structural positions such as the anchorage zones of prestressed reinforcement with dense reinforcement, the prestressed pipe in which the space of reinforcement or the thickness of concrete cover is small, the top and bottom flange of box girder and so on has brought great difficulty to concrete construction because of the small size and densely - packed reinforcement

    對于變截面t梁、工字梁、箱梁等常見結構，截面形式復雜，一些部位尺寸較小且密集配筋，如梁頂板，梁底板，預應力管道間，混凝土不可避免的造成不密實導致耐久性降低，而這些問題往往為設計者所忽略。對于新建橋梁混凝土的密實度問題，尤其是新建橋梁關鍵部位的混凝土密實度和耐久性問題，人們研究和關心的較少，這也為橋梁的質量監督控制和使用壽命埋下了隱患。
  19. The instrument has been applied to spot construction for the first time on the construction site of commanding and dispatching center of channeling water from huanghe river in wanjiazhai of shanxi. digital and sensing technology is employed to accomplish the dual open loop control over the tension of prestressing tendon. because the traditional technology of prestressing construction is improved, construction accuracy and efficiency are greatly rais ed

    智能預應力張拉儀是能與普通張拉設備配套重復使用的智能化顯示與控制儀表，是本課題組研製的專利產品，本文首次在山西省萬家寨引黃工程式控制制調度中心施工現場將智能預應力張拉儀應用於現場施工中，利用數字傳感技術實現了對預應力筋張拉的雙重開環控制，改進了傳統的預應力施工工藝，大大提高了預應力施工的精度和效率，從而有效地避免了工程事故的發生。
  20. Abstract : based on the test and analysis of 12 short restrained reinforced concrete columns with intermediate longitudinal bars, an analysis model is established to calculate the shear bearing capacities of the short columns subjected to axial load, bending moment and shear force, and with the intermediate longitudinal bars considered, the calculating formulae are derived

    文摘:根據12根配有中間筋的鋼筋混凝土約束短柱試驗與分析，建立了彎、剪、壓復合應力狀態下構件受力分析的力學模型，由此導出了考慮中間筋作用的構件抗剪承載力計算公式。
分享友人
分享到 Line

分享到臉書