配筋率 的英文怎麼說

中文拼音 [pèijīnlǜ]
配筋率 英文
amount of reinforcement
  • 配 : Ⅰ動詞1 （兩性結合） join in marriage 2 （使動物交配） mate （animals） 3 （按適當的標準或比例加以...
  • 筋 : 名詞1 （肌的舊稱） muscle2 [口語] （肌腱或骨頭的韌帶） tendon; sinew 3 [口語] （可以看見的皮下靜...
  • 率 : 率名詞（比值） rate; ratio; proportion
  1. On the base of codes in 1989, a series of seismic measures are improved in new codes, such as limit of inner - storey drift angle, minimum reinforced rate, column - beam moment magnification coefficient and moment magnification factor at the column base, etc

    在89規范的基礎上，本次規范修訂進一步提高了包括層間位移角限值、最小配筋率、柱一梁級差系數等等在內的一系列抗震設計措施。
  2. Thecalculating results show that the composite action between concrete floor and steel beamsgreatly influence the bending bearing capacity and initial rotational stiffness of joints, it shouldbe considered in practical engineer. reinforcement ratio of lengthways reinforcing bar andthe stiffener of web have great influencer on the behavior of connections, while the thicknessof end - plate and degree of shear connection have a litter influence on its behavior

    分析計算結果表明:樓板與鋼梁的組合作用對節點的抗彎承載力及初始轉動剛度的影響非常大，實際工程中節點設計應當考慮這種組合作用;樓板內縱向鋼筋配筋率與柱腹板加勁肋對節點性能影響顯著，而連接端板厚度及剪力連接程度的影響則不是太顯著。
  3. The effects to beam for its normal section flexural capacity and rigidity and ductibility as well as other properties is discussed with different polypropylene fiber and different concrete strength by the bending test study herein on the reinforced concrete beams and the polypropylene fiber reinforced beams

    本文通過對摻聚丙烯纖維砼配筋梁的試驗研究，分析討論了單筋矩形截面梁配筋率相同時，分別考慮聚丙烯纖維摻量和混凝土強度等級等因素對梁的正截面承載力、剛度及延性等幾個方面的影響。
  4. The results indicate that the ratio of span to rise, the ratio of reinforcement and the stretching controlling stress are the three primary influencing factors to the failure pattern of the slab. in addition, the relationships between the ratio of deflection to span and the ratio of span to rise and the stretching controlling stress submit to linear curves, the relationship between the ratio of deflection to span and the ratio of reinforcement submits to a quadratic parabola curve

    運用數值分析程序計算了175組不同跨高比、配筋率、張拉控制應力的中強（ 1270mpa ）螺旋肋鋼絲預應力空心板，結果表明跨高比、配筋率、張拉控制應力是影響空心板破壞形態的主要因素，且構件撓跨比與跨高比和張拉控制應力呈線性關系，與配筋率呈二次拋物線關系。
  5. Not only the load is considered, but also the distance, the span, the wide and the percent of the reinforcement is considered. the chosen section is also meeted the stiffness

    該公式不僅考慮到荷載大小、而且考慮了梁格的間距、跨度、梁寬、以及梁的配筋率等因素，且所選截面滿足剛度要求。
  6. It shows that the method suggested in the paper is simple, applicable for engineering and has good precision. on the bases of the formulas deduced, and combining with relative test datas, it studies in the paper several factors influencing the bearing performance of the simple beams, such as shape of the external tendons, the equal moment segment length, span - to - depth ratio of the beam, valid initial prestress of the external tendons, area of the internal tension reinforcement, strength of the concrete, vertical distance between

    在公式推導的基礎上，結合相關試驗資料，研究了體外筋的形狀、等彎矩區長度、梁跨高比、有效張拉預應力、體內受拉筋配筋率、混凝土強度、錨固點到樑上邊緣在垂直方向上的距離、體外預應力筋水平段長度（雙折線型體外筋的情況）以及荷載類型等對體外預應力混凝土簡支梁受力性能的影響。
  7. Thus it is necessary to study moment resistance, rotation stiffness and rotation capacity of the joints. in this paper, six specimens on end - plate composite beam - to - column joints and two specimens on end - plate composite beam - to - column joints were designed to subject to static load. the factors of m - characteristics about semi - rigid composite joints, including bolts, profiled steel sheeting, beam, column, stiffen rib and reinforcement, are studied

    本文設計了6個端板型鋼-混凝土組合樑柱節點與2個端板型純鋼樑柱節點，通過對這些試件的靜力荷載試驗，重點研究了端板型鋼-混凝土組合節點的彎矩-轉角性能的影響因素，包括高強螺栓、壓型鋼板、型鋼梁、型鋼柱、加勁肋，以及混凝土板內縱向鋼筋配筋率等。
  8. Critical fatigue reinforcement ratio of concrete beams reinforced by cold - rolled deformed steel bar

    冷軋帶肋鋼筋混凝土受彎構件的疲勞界限配筋率
  9. Specimens ’ cracking load under dead - load, fatigue failure characteristic, fatigue life, deflection of span - centre, fatigue flexural rigidity, maximal crack width, development of cracks and strain of concrete and steel bars have been investigated. the influence of fatigue cycle characteristic, ratio of reinforcement, kinds of aggregate and concrete compressive strength on the specimens ’ fatigue behavior has been also investigated

    對試件的靜載下開裂荷載、疲勞破壞特徵、疲勞壽命、疲勞荷載作用下的跨中撓度、截面疲勞抗彎剛度、裂縫開展情況及最大裂縫寬度、鋼筋及混凝土在循環荷載作用下應變等內容進行了研究，分析了疲勞循環特徵值、縱筋配筋率、骨料種類、混凝土抗壓強度等因素對試件疲勞性能的影響。
  10. Additionaily, the calculation method presented by specification for design of r. c. special shaped columns ( dbj / tl5 - l5 - 95 ) is discussed. in order to study the shear responses of special shaped columns, the ratio of tensile flexural steels " the ratio of moment and the shear - span ratio were analyzed

    為了研究異形截面柱的受剪性能，本文在總結已有試驗資料的基礎上，分別討論和分析了考慮受拉縱筋配筋率、彎矩比和剪跨比對異形截面柱受剪承載力的影響。
  11. As for the simply - supported slabs, the influence of the specimen fire proof properties is tested under the different concrete intensified degrees, under the different thickness of cover and under the different concrete quota. as far as the three - span continuous slabs are concerned, a series of analysis are conducted, including the specimen internal force redistribution under the different fire condition, the specimen deformation properties, features of the specimen destroying mechanism and the fire proof capability under the various condition

    對簡支板，考察了不同混凝土強度等級、不同的鋼筋保護層厚度、不同配筋率等對構件抗火性能的影響；對三跨連續板，考察了不同受火工況下構件的內力重分佈變化情況、構件的變形性能以及構件破壞機構的特點；分析了各工況下構件的抗火性能的差異。
  12. Based on analysis and comparison of existing test data applied to existing ultimate strength prediction models, interfacial stress at the end of plate is deduced. after formulas for calculating the effective moment of inertia for frp - strengthened beams being revised and adjustment coefficient related to nominal main steel reinforcement ratio and curtailment length ratio being put forward, strength prediction formulas of compound beams under plate end debonding failure are established. in analysis of strength of compound beams under intermediate crack induced interfacial debonding failure mode, several bond strengths and their relation are introduced

    對于板端剝離破壞，在總結現有承載力模型的基礎上，利用已有試驗數據對各承載力計算公式進行了分析比較，進一步採用分階段分析法，推導了板端界面應力的計算公式，在此基礎上，採用加固復合梁有效慣性矩的修正公式，建立了考慮名義配筋率和板端偏移比影響的板端剝離破壞梁承載力的計算公式；對于跨中受彎裂縫導致的粘結破壞，闡述了常見的幾種粘結強度之間的區別和聯系，並基於拉剪粘結強度，提出了跨中受彎裂縫導致粘結破壞的承載力計算公式，並利用現有試驗結果確定了模型中的一些參數；最後，利用試驗數據對本文建立的兩種粘結破壞承載力計算公式進行了檢驗，結果基本吻合。
  13. The main achievements of this thesis are as follows : l. the effect of the frp reinforcement ratio on cracking moment is analyzed. the calculating method and corresponding calculating formulas of flexural cracking moment of frp reinforced concrete beam are put forward

    分析了纖維增強塑料筋配筋率對纖維增強塑料筋混凝土梁正截面開裂彎矩的影響，提出了纖維增強塑料筋混凝土梁正截面抗裂度的計算方法和相應的計算公式。
  14. Until now, the domestic and overseas scholar has studied the factors that have effect on performance of steel fiber reinforced concrete corbel such as shear span to depth, strength of concrete, reinforcement ratio ( including longitudinal reinforcement and stirrup ) and ratio of horizontal to vertical load. for calculating the cracking load, and ultimate load domestic and foreign scholar has brought forward a series of calculative formulas and methods have been put forward that based on statistical analysis, flexural model and truss model

    到目前為止，國內外學者已研究了剪跨比、混凝土強度、配筋率（包括縱向鋼筋和箍筋） 、水平荷載與垂直荷載之比等因素對鋼筋鋼纖維混凝土牛腿受力性能的影響，對牛腿的抗裂計算和承載力的計算，國內外學者曾提出了基於數理統計分析、彎壓模型和桁架模型等的一系列計算方法和計算公式。
  15. Have to out : 1 temperature constructional reinforcing not can place in heat area to mass concrete design. temperature constructional reinforcing of bottom of mass concrete need content that owing to temperature change produce bottom control stress smaller than anti - pull strength at the same. get minimum rate of reinforcing to content construct request

    得出： 1在大體積混凝土結構的溫度構造鋼筋配置中，構造鋼筋不宜放置於高溫區；大體積混凝土的底部溫度構造鋼筋應滿足溫度變化產生的底部約束拉應力小於混凝土同齡期的抗拉強度的要求，從而求出抗拉要求的最小配筋率。
  16. Considering the characteristics of internal force and structures of simply supported pc bridges, a novel automatically step - up method ( asum ), taking into account the influence of steel arrangement, steel ratio, stress losses of tendons and time - dependent concrete modulus, to analyze creep and shrinkage effects is presented. this method accepts all kinds of expressions of creep and shrinkage, and it is easy to calculate total stress, strain of concrete and steel and deflection of bridge at any time, the expected prediction accuracy will be obtained by further dividing the time - step within duration

    首先，針對預應力混凝土簡支梁橋的受力特徵和構造特點，提出了徐變效應分析的全量形式自動遞進法，可考慮截面上鋼筋位置、配筋率、預應力鋼筋鬆弛、混凝土彈性模量隨時間變化等影響，且計算式可適用於任何形式的收縮、徐變特性表達式；建立的公式可方便地求解任意時刻混凝土、鋼筋的應力與應變和跨中梁體的豎向變形，計算精度可方便地通過計算時段的細分來控制，直至給出滿意的結果。
  17. In kinematics similarity test, test simulates specimens in earthquake action. by the hysteretic curve, anti - seismic property of t - shaped and l - shaped short - leg shear wall can be realized

    並且研究了在動荷載作用下混凝土等級、截面配筋率和墻肢截面高厚比等因素對短肢剪力墻抗震性能的影響。
  18. In static test, t - shaped and l - shaped specimens were respectively divided into four groups according to concrete strength grades, sectional height to thickness ratio, reinforcement ratio and ratio of axial compressive force to axial compressive ultimate capacity of section. how these factors affect the load - carrying and deformation of short - leg shear wall is known by analysis the result

    在擬靜力試驗中對t形和l形短肢剪力墻分別進行了四組試驗，通過對試驗結果的分析，揭示了混凝土等級、截面配筋率、軸壓比和墻肢截面高厚比等因素對短肢剪力墻承載力和變形的影響。
  19. Influences of load ratio, materials strength and ratio of reinforcement on seismic reliability of beams were analyzed

    研究了荷載比值、材料強度等級和配筋率對梁可靠度的影響。
  20. The programs of genetics algorithms and the improved genetics algorithm are developed with c. putting some basic parameters of earthquake and other design data in the intelligent optimal design ' s program, the analysis results of lateral stiffiiess ( sectional dimension of members ), sectional reinforcement of members and structural inner forces will be gotten

    在改進的遺傳演算法優化程序中，只需要輸入一些基本的地震動參數及其他設計數據，就能給出結構側移剛度優化結果（構件截面尺寸） ，同時還給出結構內力和構件截面配筋率等分析結果。
分享友人
分享到 Line

分享到臉書