配箍率 的英文怎麼說

中文拼音 [pèigūlǜ]
配箍率 英文
stirruratio
  • 配 : Ⅰ動詞1 （兩性結合） join in marriage 2 （使動物交配） mate （animals） 3 （按適當的標準或比例加以...
  • 箍 : Ⅰ名詞（緊緊套在物體外面的圈） hoop; ferrule; band Ⅱ動詞（用竹篾或金屬條捆緊; 用帶子之類勒住） bin...
  • 率 : 率名詞（比值） rate; ratio; proportion
  1. Here the hsc of sompa is achieved through adding super - effective water reducer, fined slag and silicon fume, and decreasing the water / cement ratio. by varying the area ( spacing ) of tension bars, compressive bars, vertical links and distribution steel and embedding steel fiber and polypropylene fiber we try to improve the behaviors of reinforced high performance concrete one - way spanning slabs in bending, so that its ductility be greater than 5. with the same arrangement of steel the width of bending member is varied to observe the effect of the width / depth ratio on the ultimate compressive strain of concrete

    通過變化受拉筋含筋率和受壓筋、箍筋（鉤筋、分佈筋）含量，或摻加纖維使之成為鋼纖維高強混凝土（ sfrhsc ）和聚丙烯纖維高強混凝土（ pfrhsc ） ，對高強混凝土雙筋截面梁、板的受彎性能進行了試驗研究，試圖改善高強混凝土受彎構件的延性，使其延性比大於5 ；並在相同配筋情況下，通過變化截面寬度，研究了高強混凝土受彎構件的寬高比對壓區混凝土極限應變的影響；並對試驗構件的裂縫發展情況進行了觀測。
  2. The shear mechanism, failure mode, deformation capacity, bearing capacity and the reliability of the anchored angle steels of the wrapped steel concrete cast - in - site frame typical story exterior joints under the middle and high axial compression ratio ( n = 0. 3, 0. 5, 0. 6 ), the working performance, failure mode, and the shear capacity of top story joints under the crack moment, the hysteresis characteristic and the dissipation energy capacity of the test joints are all analysed based on the 1 / 4 model pseudo - static tests of five specimens of wrapped steel concrete cast - in - site frame exterior joints, which varied in axial compression ratio, distribution of the beam angle steels and the stirrup ratio

    基於上述分析，本次試驗通過五個外包鋼混凝土邊節點1 4比例模型的偽靜力試驗，以柱的軸壓比、梁角鋼布置形式、配箍率等為主要參數，分析外包鋼混凝土現澆框架一般層邊節點在中高軸壓比（ n = 0 . 3 、 0 . 5 、 0 . 6 ）條件下，節點的抗剪機理、破壞模式、變形能力、承載能力和角鋼錨固的可靠性；分析了頂層邊節點在張開彎矩作用下的工作性能、破壞模式和抗剪承載力；分析了試驗節點的滯回性能和耗能能力。
  3. Based on the experiment results, the damage form of abnormal exterior joint are summarized, characteristics of hysteresis curve are studied, the effect of stirrup ratio and height of column section and beam section on anti - shear property of abnormal joint are discussed, working mechanism of abnormal exterior joint is researched, the conclusion that the anti - crack and bearing capacity of abnormal joint are studied by analyzing the minor core of abnormal exterior joint is proposed, the basic data is provided for the design formula of abnormal joints

    根據試驗結果，總結了異型邊節點的破壞形態，研究了節點滯回曲線的特徵，討論了節點核芯配箍率、樑柱截面高度變化對異型邊節點抗剪性能的影響，分析了異型邊節點的受力機理，提出應以「小核芯」為分析單元來研究此類節點抗裂和承載力的建議，為異型節點設計公式的建立提供了基礎數據。
  4. Based on the pseudo - static experimental results of nine abnormal joints, the damage process of abnormal joint is divided into four stages of original crack, entire crack, ultimate state and failure, the effect of axial force ratio, stirrup ratio and height of column section on seismic behavior of abnormal joint are discussed, the conclusion that anti - shear capacity of abnormal joint are studied in entire crack state by studying the minor core of abnormal joint is made, the calculating formula for anti - shear capacity of abnormal joint is proposed with a view to asymmetry in stirrup yield

    摘要根據9個鋼筋混凝土框架異型節點試件的擬靜力試驗結果，指出異型節點受力過程分為初裂、通裂、極限和破壞4個階段；討論了軸壓比、節點核芯配箍率、柱截面高度變化對異型節點抗剪性能的影響；提出應考慮節點核芯區箍筋屈服的不均勻性並在通裂狀態下以「小核芯」為分析單元來研究此類節點抗剪承載力的建議；最終給出了異型節點抗剪承載力的計算公式。
  5. The influence of such parameters as axial load index, aspect ratio and percentages of lateral reinforcement, on seismic performance of reinforced concrete frame column in hong kong and analyses the distribution relationships of flexural deformation, shear deformation and slippage of longitudinal reinforcement in joint zone

    根據試驗結果，討論了軸壓比、配箍率、剪跨比等參數對其抗震性能的影響，分析了水平荷載作用時塑性鉸區的彎曲變形、剪切變形和縱向鋼筋粘結滑移變形所產生的位移在框架柱總水平側移中所佔的比例及其變化規律。
  6. Six circular concrete columns were tested under concentric loading, to investigate the confinement effect of confining reinforcement in both normal strength and high strength concrete columns. test results were analyzed and compared. practical formulas were proposed for the minimum volumetric ratio and the spacing of the stirrups

    通過對6根圓柱體混凝土柱的軸壓試驗，研究普通混凝土及高強混凝土在箍筋作用下的約束效應，並將試驗結果進行分析比較，提出了配箍率及箍筋間距實用計算公式。
  7. An analysis is developed for influence factors that have some influence on joints " behavior. the results show that axial ratio has a good and visible effect on the capacity of joints ; that the higher concrete strength is, the higher the capacity of joints is ; the ratio of reinforcements and the thickness steel web of column have large influence on the ductility src joints, not but the capacity of src joints

    分析表明：軸壓比對節點的剛度、抗裂度的提高是有利的，且增大幅度較大；節點承載力和抗剪能力隨混凝土等級的提高而提高；鋼腹板厚度和配箍率的增大對節點承載力提高幅度不大，其對節點的延性影響較大。
  8. Until now, the domestic and overseas scholar has studied the factors that have effect on performance of steel fiber reinforced concrete corbel such as shear span to depth, strength of concrete, reinforcement ratio ( including longitudinal reinforcement and stirrup ) and ratio of horizontal to vertical load. for calculating the cracking load, and ultimate load domestic and foreign scholar has brought forward a series of calculative formulas and methods have been put forward that based on statistical analysis, flexural model and truss model

    到目前為止，國內外學者已研究了剪跨比、混凝土強度、配筋率（包括縱向鋼筋和箍筋） 、水平荷載與垂直荷載之比等因素對鋼筋鋼纖維混凝土牛腿受力性能的影響，對牛腿的抗裂計算和承載力的計算，國內外學者曾提出了基於數理統計分析、彎壓模型和桁架模型等的一系列計算方法和計算公式。
  9. Then, this paper edits other computer program to calculate thirty sgrc frame columns, and researches the drift capacity of sgrc frame column, and analysis the turning capacity of frame column " s plastic hinge. then the relational expression of the curvature ductility factor and ratio of hoops of sgrc frame columns is derived. this paper analysis the relation of the curvature ductility factor and the relative drift of sgrc frame columns, and discuss the question of the minimum values of ratios of hoops of sgrc frame column at different axial load ratios

    一11一太原理工大學碩_ i :學位論文使用本文程序另外模擬計算了30榻煤研石混凝土框架，進一步分析了軸壓比和配箍率對煤研石混凝土框架柱曲率延性的影響，編寫程序計算了30根煤研石混凝土框架柱，對煤研石混凝土框架柱的側向變形能力進行了研究，分析了柱塑性鉸的轉動能力，導出了煤研石混凝土框架柱的曲率延性系數與配箍率的關系式，分析了煤研石混凝土框架柱的曲率延性系數與框架柱相對側向位移的關系，討論了煤研石混凝土框架柱在不同軸壓比下最小配箍率的取值問題。
  10. It has little effect on the enhancement of ultimate bearing capacity of frame column that the ratio of the hooped reinforcement in the joint area is increased again after it is up to a certain degree

    節點區箍筋加密到一定程度再提高配箍率，對框架柱極限承載能力的提高已沒有多大效果。
  11. The result appears that the strength, hardness and ductility of corroded rc beam decrease with corrosion ratio, and the structure failure mode may change from flexural failure to shear failure when stirrup ratio is low

    研究表明，銹蝕受彎梁的強度、剛度和延性隨著銹蝕率的增加而減少。對配箍率較小的銹蝕梁，其破壞形態可能從受彎破壞轉變為受剪破壞。
  12. In order to determine the relations between the four main bond - anchoring factors - concrete strength, concrete cover thickness, steel shape embedment length and the ratio of the transverse hoops - and the bond strength, and establish the bond - slip constitutive relations, 16 standard push - out test specimens were designed, and 4 comparison specimens were additionally designed to find the difference of the bond performance between the web, inside and outside of flanges the steel shape

    設計了16個型鋼混凝土標準推出試件，以考察混凝土強度、型鋼的混凝土保護層厚度、型鋼埋置長度及橫向配箍率四個主要錨固條件與粘結強度的相互關系和型鋼混凝土粘結滑移本構關系；設計了4個對比試件，以考察型鋼翼緣內側、外側和腹板與混凝土粘結性能的區別。
  13. Based on the tests, the advised formula of normal section bearing capacity and inclined section bearing capacity of high strengthen concrete frame columns are put forward, and the limit of axial compressive ratio and the minimum stirrup ratio in the encrypted region which meet ductility requirement to c60 concrete frame columns are given

    在試驗研究的基礎上，提出高強混凝土框架柱正截面和斜截面承載力計算的建議公式，且給出了滿足延性要求的c60混凝土框架柱軸壓比限值和箍筋加密區箍筋的最小體積配箍率。
  14. By changing the parameters of stirrups ratio and axial load ratio, 6 high strength concrete ( hsc ) columns are tested subjected to cyclic lateral load. the baring capacity of hsc columns with new form of stirrups are compared with hsc columns with normal form of stirrups. load - displace relation curves are obtained

    本文以體積配箍率和軸壓比為主要控制參數，對不同配筋模式的6根高強混凝土壓彎構件進行了低周水平反復加載試驗，得到了箍筋約束混凝土的荷載?位移滯回曲線。
  15. When the axial compression ratio increases more than 0. 42, the variation of the displacement ductility ratios is small ; when the stirrup ratio per unit volume increases more than 1. 9 %, the displacement ductility increases slowly ; with increasing the shear span ratio a, the displacement ductility increases for, < 1. 5, decreases for > 1. 5

    當軸壓力系數增加到0 . 42以後，位移延性的變化較小；體積配箍率增加到1 . 9 %后，位移延性的增長減緩；當剪跨比小於1 . 5時，型鋼混凝土柱的延性系數隨剪跨比的增加而提高；但當剪跨比大於1 . 5時，隨著剪跨比的增加，型鋼混凝土柱位移延性系數有所降低。
  16. 5 results of an experimental investigation on shear behavior of l, t and + - shaped columns are presented. the effects of shear - span ratio, axial compression ratio, stirrup contents and loading direction on shear behaviors of l, t, and + - shaped columns are discussed. combining with test data of others, the formulas for shear strength of l and + - shaped columns are given

    5對l 、 t 、十形柱受剪性能進行了低周反復荷載試驗研究，討論了剪跨比、軸壓比、配箍率、荷載作用方向對l 、 t 、十形柱承載力和延性的影響，並結合他人試驗結果，提出了l 、十形柱的偏下線受剪承載力公式。
  17. The objective function is the cost of anti - slide pile " s per meter ; the constraint conditions are the strength of anti - slide pile " s normal section and inclined section, the ratio of reinforcing design and the size of section in the design code ; the design variables are the height of section, the area of reinforcement and the amount of hoop. and the optimization model is solved by 0. 618 method

    本文提出的優化設計方法，以樁單位長度的總造價為目標函數，以規范對單筋梁的正、斜截面強度，配筋率及截面尺寸等要求為約束條件，以樁截面高度，抗彎縱筋面積，抗剪箍筋數量等為設計變量，來建立優化模型，並用0 . 618法進行求解。
  18. The main contents are followed below : ( 1 ) for the aim of knowing the characteristics of main factory building structure frame columns of large - scale thermal power plants, nine high strength concrete frame columns with high axial compression ratio and six slender ordinary strength concrete frame columns with high axial compression ratio were tested under low reversed cyclic horizontal loading for the very first time, and thus the influencing factors of normal section bearing capacity, such as concrete intensity grade, axial compressive ratio, slendemess ratio, the type of stirrups and stirrup ratio, etc, the anti seismic deformation capability of frame columns were acquired

    本文主要研究的內容有： （ 1 ）首次針對火電廠主廠房結構框架柱的特點，對9個高軸壓比高強混凝土框架柱和6個高軸壓比普通混凝土框架長柱進行了低周反復水平加載試驗，獲得混凝土等級、軸壓比、長細比、配箍形式及配筋率等對框架柱的抗彎及抗剪承載力、抗震變形能力的影響因素。
分享友人
分享到 Line

分享到臉書