重心縱向位置 的英文怎麼說

中文拼音 [zhòngxīnzōngxiàngwèizhì]
重心縱向位置 英文
longitudinal center of gravity
  • 重 : 重Ⅰ名詞（重量; 分量） weight Ⅱ動詞（重視） lay [place put] stress on; place value upon; attach im...
  • 縱 : Ⅰ動詞1 （釋放; 放走） release; set free; let go 2 （放任; 不約束） indulge; give oneself up to; l...
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 重心 : 1 （事情的中心或主要部分） heart; core; focus; key point 2 [物理學] centre of gravity; barycentre...
  • 縱向 : [造紙] direction; machine direction; endwise; longitudinal direction; vertical; longitudinal縱向...
  1. By changing position research of airship ' s center of gravity to control longitudinal motion

    改變飛艇重心位置控制縱向運動
  2. The influence analysis is achieved for maneuverability and stability of the coach - bus while the angel stiffness of it ' s lateral stable pole or the position of gravity center is changing

    並討論了橫向穩定桿角剛度變化、重心位置變化對大客車操縱穩定性的影響。
  3. Numerical simulation by cfd was carried out to understand the hot current behavior in a tunnel with longitudinal ventilation. it becomes clear that fire source modeling is very important because the hot current behavior is strongly affected by the fire source position and is sensitive to methods in the modeling of the fire source. the flame area which has developed from the fire source is an area of chemical reaction caused by combustion. even if grids in the vicinity of the fire source are made fine, it was difficult to simulate the heat generation area with consideration to this chemical reaction through using a method for setting the heat release rate simply on the fire source surface. therefore, we proposed a method adopting the knowledge on flame shape under the longitudinal ventilation and incorporating it into numerical simulation and it showed a good agreement with the experimental results. it was shown through experiments in a tunnel with longitudinal ventilation that the hot current developed toward the tunnel center downwind from the fire source near a wall. the cause was investigated by numerical simulation and it became clear from the results that the spiral air by the fire plume created a vortex in the crevice between the wall and the plume

    運用cfd進行數字模擬，以了解縱向通風隧道內熱煙氣流的特性.通過模擬發現對火源進行模擬非常重要，熱煙氣流特性受火源位置的影響很大，並且對火源模擬方法很敏感.火源生成的火焰區是燃燒引起的化學反應區域.即使火源附近的木垛排列完好，也很難在考慮這些化學反應條件下模擬熱生成區域.建議考慮縱向通風隧道內火焰形狀並對它進行數字模擬.模擬結果與試驗結果非常吻合.試驗證明，在縱向通風隧道內，熱煙氣流從靠近墻體火源處順風向隧道中心蔓延.數字模擬結果發現，火災羽流造成的螺旋上升空氣會在墻體和羽流之間形成一個渦流區
  4. Abstract : numerical simulation by cfd was carried out to understand the hot current behavior in a tunnel with longitudinal ventilation. it becomes clear that fire source modeling is very important because the hot current behavior is strongly affected by the fire source position and is sensitive to methods in the modeling of the fire source. the flame area which has developed from the fire source is an area of chemical reaction caused by combustion. even if grids in the vicinity of the fire source are made fine, it was difficult to simulate the heat generation area with consideration to this chemical reaction through using a method for setting the heat release rate simply on the fire source surface. therefore, we proposed a method adopting the knowledge on flame shape under the longitudinal ventilation and incorporating it into numerical simulation and it showed a good agreement with the experimental results. it was shown through experiments in a tunnel with longitudinal ventilation that the hot current developed toward the tunnel center downwind from the fire source near a wall. the cause was investigated by numerical simulation and it became clear from the results that the spiral air by the fire plume created a vortex in the crevice between the wall and the plume

    文摘:運用cfd進行數字模擬，以了解縱向通風隧道內熱煙氣流的特性.通過模擬發現對火源進行模擬非常重要，熱煙氣流特性受火源位置的影響很大，並且對火源模擬方法很敏感.火源生成的火焰區是燃燒引起的化學反應區域.即使火源附近的木垛排列完好，也很難在考慮這些化學反應條件下模擬熱生成區域.建議考慮縱向通風隧道內火焰形狀並對它進行數字模擬.模擬結果與試驗結果非常吻合.試驗證明，在縱向通風隧道內，熱煙氣流從靠近墻體火源處順風向隧道中心蔓延.數字模擬結果發現，火災羽流造成的螺旋上升空氣會在墻體和羽流之間形成一個渦流區
  5. In case of the longitudinal and lateral centerlines of the figure of the loaded car are asymmetric when freights are normally loaded, and considering the allowed shift in the longitudinal and lateral direction, the weight value and position of balances are deduced and an example is given

    摘要貨物正常裝載時，外形輪廓關于負重車縱、橫中心線都不對稱的情況下，考慮到貨物的縱、橫向偏移，對配重物的重量及位置進行了推導，並舉了實例。
分享友人
分享到 Line

分享到臉書