重載吃水 的英文怎麼說

中文拼音 [zhòngzǎijíshuǐ]
重載吃水 英文
load draft
  • 重 : 重Ⅰ名詞（重量; 分量） weight Ⅱ動詞（重視） lay [place put] stress on; place value upon; attach im...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 吃 : Ⅰ動詞1 （吃東西） eat; take; make 2 （在某一出售食物的地方吃） have one s meals; eat 3 （依靠某種...
  • 水 : 名詞1 （由兩個氫原子和一個氧原子結合而成的液體） water 2 （河流） river 3 （指江、河、湖、海、洋...
  1. In the study of the lumber carrier, one of the very important problem is the in spot and ultimate station due to flooding which will bring tremendous threat to the ship because of the few holds in order to study the lumber carrier buoyancy, stability and longitudinal strength under the condition of flooding, the paper adopt fundamental ship principle and iterative and accumulative concept on the basis of insumersibility theory to detailedly calculate the flooding speed flooding amount front draft after draft stability and longitudinal strength considering the ship " s sinking and inclination which will change the center of gravity and the loading station both in hold and on deck and the effect of flooding and lumber amount in holdo in the last, the paper introduces an example of the actual ship named " fei yun ling " and makes a contrast between not taking measure and taking measure which draws a reasonable conclusion and comes up to some advice the method avoids the cockamamie calculating while insures enough precision the paper draws a conclusion that not all the lumber carrier will submerge when suffering the damaged flooding if the loading or measure is suitable

    為了研究運木船舶在破艙狀態下的浮性、穩性和強度，本文在抗沉性理論的基礎上，運用船舶基本原理，採用了迭代和累計的思想，將船舶的進水過程劃分為很多次進水的積累，詳細計算了運木船在破艙進水的過程中，考慮到各種破艙參數、船舶本身的下沉、艙室內木材、甲板貨的裝載情況和在進水過程中船舶本身的傾斜對進水重心的影響，以及艙室內的進水量和木材對破口處進水速度的影響，船舶總的進水速度、進水量、首尾吃水、穩性的實時狀態和最終船舶的總縱強度，給出了計算實例，並進行了在採取用泵抽水前後浮態參數的對比，得出了該船舶在艙室內的貨物積載量達到某個數值時可以保證船舶在破艙進水時不會沉沒，或者在當開口小於某數值時，採取適當的措施后，可以使船舶避免沉沒。
  2. Ship ' s name, port of registry, draft marks and loadline marks to be dressed and repainted

    船名，船籍港，吃水標志和載重線標志需修飾，重刷。
  3. Inspecting fitting accuracy of draught mark ( loading line mark )

    吃水標志（載重線標志）安裝精確性檢查。
  4. In the course of stowage of heavy article, officers and engineers concertrat their attention on the calculation of vessel " s parameters and the limitation that be bringed by many factors to loading position, and don " t think much of the affection of awkward lengthy cargo " space size to loading position

    在一般的重大件貨物積載過程中，往往側重於船舶的吃水、吃水差、穩性高度和傾角各參數及各因素對裝貨位置的限制，不太重視重大件貨物的空間形狀大小對裝貨位置的影響。
  5. Since kamen and vagena, many researchers have discussed it in theory and experiment method. the main content in this paper is to set forth the slamming press calculations in dnv rules, gl rules and lr rules and the requirements for slamming strengthened bow structure and some comparisons ; slamming strengthened bow structure design for a bulk is carried out using dnv rules, and comparisons among several design schemes is carried through when heavy loading draft status replaces light loading draft status in practice. the results from above have been applied in ship production ; it is significant for ship structure improvement latter to calculate slamming press with direct calculation method, and then to design bow structure with dnv rules

    本文的主要內容是分別闡述dnv 、 gl 、 lr三種規范對底部砰擊壓力計算及底部砰擊加強結構設計的一般要求並進行一些分析比較：用dnv規范對某型船（ 27000t散貨船）進行具體的底部砰擊加強結構設計，並就實際生產中產生的重載吃水狀態改輕載吃水狀態而出現的幾種設計方案進行比較，其具體結果現已用於實際生產；用直接計演算法確定砰擊壓力，再用dnv規范進行底部結構設計，對於後續船的改進均有指導意義。
  6. But in fact, it is not equal for the lashings " parameters. this dissertation starts with computer graphics and put forward the conception of three - dimensional object " s touch or collision. and simulate the course of loading cargo, and solve the issue through that course

    並應用計算機編程模擬裝貨過程，解決三維物體的觸碰問題，預吊裝及裝載重大件貨物、並在吊裝過程中顯示船舶的吃水、吃水差、穩心高度和傾角，還有岸吊的水平轉角、豎直轉角及吊索的長度。
分享友人
分享到 Line

分享到臉書