量熱器卡計 的英文怎麼說
中文拼音 [liángrèqìkǎjì]
量熱器卡計
英文
calorimeter-
The control system of furnace " s temperature has been widely used in every walk of life, as an important link of repair and manufacture of the electrical equipment such as electromotor transformer etc., soaking lacquer drying craft has some especial requests on drying crafto this article starts with the analysis of drying chamber " s configuration, analyzed its configuration limitation and control function limitation according to the factory " s situation and advances the conception of heated air drying circulation, in addition, this article adopts an intellectualize a / d module, a development sampling tuning - voltage circuit, and presents the method to measure online the insulation resistance of products in order to improve constantly products quality
而浸漆乾燥工藝作為電機、變壓器等電氣設備的修理、製造中的重要環節之一，對乾燥過程的質量要求有一定的特殊性。該文從乾燥爐的結構分析入手，聯繫到工廠的實際情況分析了結構功能缺陷和控制功能缺陷，提出了熱風循環乾燥的概念，同時，選擇了較為先進的a d板卡、熱電阻信號調理板等專業化智能卡，運用數字pid控制技術，構成了一個較有特色的計算機控制系統。此外，該文還從保證乾燥品質量的角度，採用智能化交流模塊和自製采樣調壓電路的方法，提出了在線檢測產修品的絕緣電阻的方法和手段，以確保企業產品質量不斷提高。According to the demand of the concept design of china spallation neutron source ( csns ), the target station, i. e. the target, the reflector and the moderator have been simulated and optimized using monte carlo simulation software, nmtc / jam and mcnp4a, firstly. the neutron flux escaping from the target and the moderator and the heat deposition in the target, the reflector and the moderator are calculated. these results provided essential data as a basis of the spallation neutron source design
本論文結合當前中國散裂中子源（ chinaspallationneutronsource ， csns ）工程概念設計的迫切需要，選擇國際上廣泛使用的基於蒙特?卡羅方法，用於模擬粒子輸運過程的程序mcnp4a和nmtc jam作為研究工具，首次對csns靶站進行了全面的模擬與優化，內容包括靶、反射體與慢化器系統的中子通量分佈以及熱量沉積，同時計算了靶的溫度場與應力場分佈。Heating centralized is an important thing in the north. whether this is implemented in a large scale has contributed to impove city modern level and ameliorate atmosphere environment. the traditional heating system are two - upright - pipe - parallel system, two - pipe system, single - pipe - stride system etc, whose calculation for heat charge is either by man or by ic installed on the caliduct. therefore, the problem arise that heat provided does n ' t accord with heat charge payed, not secure, and resident have to suffer much
傳統的供暖系統有雙立管水平式系統、全雙管系統、單管跨越式系統等，其計費方式要麼為人工計費，要麼是利用安裝在暖氣片上的帶電讀卡器，這樣存在著供熱量與收費額匹配不準確、不安全等方面的問題，也使集中供熱用戶有苦難言。The algorithm of strapdown inertial navigation system is also discussed and then use the flight - track generator to give a simulation, since a closed loop feedback integrated navigation system is designed in this paper, and the output of the filter must feed back to the strapdown inertial navigation system, the analysis of the algorithm in strapdown inertial navigation system is important. the scheme to design the trajectory of gps and the simulation of gps constellation are then studied, the simulation of gps constellation is given from the calculation of vernal equinox base on the principle of celestial mechanics, this method of different from other methods given by other paper and is useful to the research of satellite navigation system. a new method to abstract noise modal in integrated navigation system is proved to be useful in practice, this method, which is given by use the principles of stochastic processes, statistics, time series analysis, and system identification, is suitable for the kalman filter in integrated navigation system
如航跡產生器的設計，該航跡產生器是研究組合導航問題的前提，從國外一些研究組合導航系統的文獻中可以看出，設計這樣一個航跡產生器是非常必要的，所以本文自行設計了這樣一個系統；還討論了捷聯慣性導航系統中捷聯解算的方法，並進行了模擬研究，由於在本文設計的閉環反饋式組合導航系統中，對捷聯慣導系統的平臺誤差進行閉環控制，需要將濾波器輸出的校正量反饋到捷聯解算內部，所以必須對捷聯解算進行深入的研究和分析，更何況捷聯解算問題本身也是導航界的一個熱門研究課題；另外，本文還介紹了gps軌道及其星座模擬的設計思想和方案，與以往gps軌道和星座模擬不同的是本文從天體力學中計算春分點開始，逐步進行gps軌道及其星座模擬，這樣的設計方法對從事衛星導航的研究工作是有價值的；還對組合導航中誤差建模方法進行了研究，綜合運用隨機過程、概率統計、時序分析及系統辯識等方面的理論提出了一套適合組合導航卡爾曼濾波的誤差建模方法，並運用實際研究工作中的測量數據對該方法進行了驗證。分享友人