金屬面層合板 的英文怎麼說

中文拼音 [jīnzhǔmiàncéngbǎn]
金屬面層合板 英文
metal faced plywood
  • : Ⅰ名詞1 (金屬) metals 2 (錢) money 3 (古時金屬制的打擊樂器) ancient metal percussion instrum...
  • : 屬名詞1 (類別) category 2 [生物學] (生物分類系統上所用的等級之一) genus 3 (家屬; 親屬) fami...
  • : Ⅰ名詞1 (頭的前部; 臉) face 2 (物體的表面) surface; top 3 (外露的一層或正面) outside; the ri...
  • : i 量詞1 (用於重疊、積累的東西 如樓層、階層、地層) storey; tier; stratum 2 (用於可以分項分步的...
  • : 合量詞(容量單位) ge, a unit of dry measure for grain (=1 decilitre)
  • : Ⅰ名詞1 (片狀硬物體) board; plank; plate 2 (專指店鋪的門板) shutter 3 [音樂] (打拍子的樂器) ...
  • 金屬 : metal
  1. In this paper, a high performance sma system applied to steel bridge deck is put forth in allusion to the pavement project of the wuhan junshan yangtze river highway bridge. it comprises steel slab, zn coating layer, closing layer, adhesive, pre - mixed asphalt stone and dual layer sma from bottom to top. it is based on the fea results of the forces and deformation of the pavement layer by means of the algor feas, according to this bridge ' s traffic and the ambient temperature varying range of the pavement layer

    本文針對武漢軍山長江公路大橋鋼箱梁橋鋪裝工程,從鋪裝環境溫度變化范圍、交通量等使用條件出發,在用algorfeas有限元分析軟體分析鋪裝受力變形基礎上,提出了(即鋼+鋅塗+封閉+粘接劑+預拌瀝青碎石+雙sma )的高性能鋼橋sma鋪裝體系,並對這種sma的組成材料,包括改性瀝青、集料、礦粉、纖維進行了比較研究,設計了這種sma的配比,對sma混料的性能進行了對比試驗,對這種sma方案進行了疲勞性能研究,驗證了所選擇sma方案的可行性。
  2. During the past years a great deal of interest has been devoted to the study of ceramic composite armor due to the application in defense, in the light of recent work of ceramic / composite armor the dissertation provides the defensible performance of ceramic / metal, ceramic / non - metal light armor and multi - layer ceramic composite armor and its optimization design. at one time, it motives us to study the smash mechanism of ceramic facet plate under the effect of impact load and to analyzed different defensible performance from homogeneous armor

    本文針對陶瓷復裝甲的研究現狀,深入系統地研究了陶瓷/、陶瓷/非輕型裝甲和陶瓷多裝甲的抗彈性能及優化設計,同時研究了在沖擊載荷作用下陶瓷的破碎機理,對陶瓷復裝甲不同於均質裝甲的抗彈性能進行了分析。
  3. Pressed metal plate size and allow deviation, surface quality, quality coating should comply with the design requirements and norms

    壓型的尺寸及允許偏差、表質量、塗質量等應符設計要求和規范的規定。
  4. However, the die attach layer delaminated after 500 cycles and pcb cracked in the underfilled samples after long time cycling. c - sam is employed to investigate the delamination in the underfilled samples. highly concentrated stress - strain induced by the cte mismatch between the bga component and the pcb board, coarsened grain and two kinds of intermetallic compounds ( nisn / nisns ) which formed during reflow and thermal cycle and their impact on the reliability of solder joints are discussed in this paper

    充膠樣品粗化尤為嚴重; ? ni - sn間化物包括兩:其中,靠近ni焊盤的那比較平整,同時, eds結果分析表明其化學式近似為nisn ,而靠近焊料的那條狀,化學式近似為nisn _ 3 ,文獻表明其為亞穩相; ?充膠使得樣品最大應力范圍降了接近一個數量級並降低了dnp的作用,同時,器件失效模式變為晶元粘接; ? c - sam結果表明本論文採用的充膠樣品,晶元粘接起始於500周左右,而經過2700周循環的樣品,分幾乎擴展到整個界
  5. Standard practice for surface preparation and structural adhesive bonding of precured, nonmetallic composite facings to structural core for flat shelter panels

    遮蔽向結構芯的預硫化非的表制備和結構粘結的標準實施規程
分享友人