鉆井參數 的英文怎麼說
中文拼音 [zhēnjǐngshēnshǔ]
鉆井參數
英文
drilling parameter-
Optimum design parameter of mud liner motion shale shaker
鉆井液直線振動篩參數的優化設計In this paper, the sensibility analysis of the factors affecting the temperature in well bore is relatively systematically made by using a large number of the data calculated with the borehole flow and heat transfer 3 ? d numerical model proposed by the author. the study shows that the thermophysical parameters of the drilling fluid and formation, etc. and the entrance temperature and circulating capacity, etc. of drilling fluid have a greater influence on the temperature in well bore. therefore, accurately mastering the thermophysical parameter values of penetrated formation and drilling fluid in well bore, considering the influence of the temperature and pressure on thermophysical parameters and accurately measuring such parameters as entrance temperature and discharge capacity of drilling fluid, etc. are of utmost importance for accurately simulating the temperature in well bore
利用由作者提出的井內流動和傳熱的三維數值模型計算所得的大量數據,文章對影響井內溫度的諸多因素進行了較系統的敏感性分析,研究表明:鉆井液和地層等的熱物理參數以及鉆井液的入口溫度、循環排量等對井內溫度有較大影響,因此,準確掌握所鉆地區地層和井內鉆井液的熱物理參數值,考慮溫度壓力對熱物理參數的影響,準確測量鉆井液的入口溫度、排量等參數值,對于井內溫度的準確模擬至關重要。Parameters can be interpreted through the method used in straight wells. after logging curves in horizontal wells are revised to true vertical depth, oil - bearing formation is evaluated through the comparison of wells combined with geological information. logging while drilling have great difference with ordinary cable logging especially in deviated holes and horizontal wells. comparison of cable logging and lwd carried out in different time indicates characters of mud invasion
實際解釋lwd資料時首先需對隨鉆測井資料進行預處理和標準化,然後從隨鉆測井、錄井資料中提取與巖性密切相關的參數,建立測井相-巖相統計模式,並採用灰色關聯識別方法實時判別地層巖性;採用直井的參數解釋方法進行隨鉆地層參數解釋;將水平井的隨鉆測井曲線從實際井深校正到垂直井深上,通過隨鉆測井資料與鄰井測井資料的對比解釋,並結合地質、錄井資料進行隨鉆地層含油氣性評價。In order to geosteering, log - geology model of target formation should be built according to logging data and the interpreting result of wells nearby. geosteering parameters model is created to build simulative curves. compared these curves with logging curves, the position and drilling direction of the bit can be found combined with the concrete geological situation
要實現地質導向,首先要根據鄰井的測井資料及其解釋結果建立目標層測井地質模式,然後通過建立地質導向參數的預測模型構造相應的模擬曲線,將模擬曲線與實測曲線進行對比,結合具體地質情況,確定鉆頭在目標層中的位置及其鉆進方向,及時調整井眼軌跡,使其始終保持在目標層中物性最好的部位。This paper, based on normalizing well logging data while drilling and correcting depth into true vertical depth and calculating reservoir parameters and etc, combining the practical ease of mobei oilfield, extracted logging and geological pattern characteristic of target oil - gas formation and geosteering mark formation, and used bp neural network and regressive analysis to create predicting mode of geosteering parameter to build relevant contrast curve ; adopted geometry geosteering method to fix on die drilling direction of bit upper and declination, the position in reservoir, to judge the real drilling case. all finely solved the problem to follow the geological target while drilling for three horizontal well these methods improve the drilling horizontal well ability by using the techniques to follow the geological target while drilling, and then it is convenient and practicable
本文在開展隨鉆測井資料的標準化和斜井校正及儲層參數解釋與含流體性質判釋等工作的基礎上,結合研究工區莫北油田的實際情況,提取了目標油(氣)層和導向標志層的測井地質模式特徵,並採用bp神經網路法和回歸分析法建立了地質導向參數的預測模型、構造了相應的對比曲線;採用幾何導向法確定鉆頭上下傾鉆進方向及其在目標層的位置,以判斷實際鉆進地層情況,很好地解決了研究工區三口水平井的隨鉆跟蹤地質目標的問題。The strength of legs of a jack - up drilling platform serviced in bohai sea is evaluated and the ice - induced fatigue damage of the platform leg under different ice parameter was determined
對渤海某自升式鉆井平臺樁腿進行了強度校核,計算出不同海冰參數下平臺樁腿的冰激疲勞損傷。Drilling instrument is the major application to monitor and analyze the drilling process, making drilling more safe and rational
鉆井參數儀表是鉆井工程監測鉆井過程、進行科學分析和科學決策的重要工具。Drilling parameters instrument is the important implement to monitor and analyze the drilling process, and to make scientific decision - making about drilling process
鉆井參數儀表是鉆井工程中監測鉆井過程、進行科學分析和科學決策的重要工具。The sidetrack technical keys in ultra - deep well such as engineering design, selection of the kop, field operation and drilling parameters are discussed as well as the field operation rules, which can be beneficial to sidetracking operations in ultra - deep wells as reference
從工程設計、造斜點的選擇、現場施工、鉆井參數等方面討論了超深側鉆井的技術要點以及現場施工的規律,對于超深井側鉆施工具有一定的借鑒意義。This thesis preliminarily researched drilling technology of applying foaming dth hammer into hydrology and waterwell drilling beginning with analyzing foaming dth hammer ' s structure characteristics and working principle and joining together with the indoor experiment with respect to the fitting of drilling equipments, designing of grouting system, selecting of drilling program parameters and so on
從分析泡沫潛孔錘的結構特點和工作原理出發,結合室內實驗,在鉆進設備的配套、灌注系統的設計、鉆進規程參數的選擇等方面,對泡沫潛孔錘應用於水文水井鉆探的鉆進工藝進行了研究。The sofware design of drilling fluid rheology parameter automation detect system
鉆井液流變參數自動檢測系統軟體設計Viscosity should be maintained above 45 sec / qt. maintain with xcd rather than with bentonite. monitor hole cleaning at shakers and adjust low end rheology as required
鉆井液粘度應當保持在每誇脫45秒左右,要用生物聚合物來維護,不要用膨潤土。通過振動篩觀察井內是否干凈,按要求把最終的流變參數調低。The comprehensive geological characteristic has been fully studied in this paper. on the basis of this, closely combining production practice, the favorable gas developing regions have been determined with the methods of sedimentary facies and combination of generation, reservoir and caprock, and logging parameters interpretation maps and regression formulas have been established with logging data, as well as reprocessing, interpretation and identification of gas reservoir have been done with computer. integrating the information and results of geology, logging, testing and geophysics, the gas reservoir distribution regularity of structure of no. 1 sebei has been described and reserves in place of no. 1 ' sebei gas field have been recalculated, which have provided a basis for next step of development in research area
在近十多年,通過提高地震資料處理精度、淡水聚合物泥漿的應用、數字測井技術的運用、並加強了低電阻層和差物性層的試氣及氣田擴邊鉆探,大大提高了對氣層的識別,大量增加了氣層的層數和厚度,擴大了氣田的含氣面積,使氣田儲量通過多次復查核算仍在不斷增加本論文充分研究了青海澀北一號氣田天然氣地質綜合特徵,並以此為基礎緊密結合生產實踐,應用沉積相與生儲蓋組合等方法確定氣藏有利發育區帶,應用測井資料建立測井參數解釋圖版並回歸公式,應用計算機重新處理、解釋和識別氣層,綜合地質、測井、試井、物探等多方面信息與成果,描述了澀北一號構造的氣層分佈規律,重新計算了澀北一號氣田的地質儲量,為研究區下一步開發提供了依據。Research on the optimization of bit type and drilling paramrter in daqing gas field
慶深氣田鉆頭類型與鉆井參數優選研究These days, the drilling instruments are changing from mechanical, hydraulic meters to digital, integrated, intelligent and networklized ones
目前鉆井參數儀表正在經歷一次重大革命,正在由過去的機械、液壓儀表向數字化、集成化、智能化和網路化方向發展。The reliable detection of this transition zone depends on the fact that if all drilling parameters remain relatively constant. the following indicators are noted
對這種變化層位的監測,主要取決于所有的鉆井參數是否能維持相對穩定的常數,為此對下列顯示要引起注意。The domestic ones left behind hi reliability, accuracy and man - computer interface. aiming at the problem of existing drilling parameters monitoring system, a new monitoring method of drilling parameter is explored
總體上看,國內外鉆井參數的測量原理和方法都還有待改進和完善,國內鉆井參數儀表在可靠性、精度和人機界面等方面與國外相比又還有一定差距。Finally , the factor which play a decisive role is presented , it provides a theoretical support for cementing operation and how to adjust and control the drilling as well as how to determine cementing parameters
運用模糊數學的理論之一?多級綜合評判方法對影響固井優質率的三大因素進行了綜合評判,初步得出了哪一類因素起著主導作用的結論,為固井作業施工以及如何合理地進行調控鉆井參數和固井作業參數提供了理論依據。Using new technology of fieldbus and client / server, a real - time and multi - parameter drilling monitoring system with high precision, complete function, beautiful and friendly interface is developed. the system has been applied in drilling scene and gets fine application effect. to solve the problems mentioned above, the article discusses the measuring methods and building of the mathematic model, and by adopting bus and user / server, develops a real - tune multi - parameter drilling monitor system of high accuracy and friendly interface
本文針對以往國內鉆井參數儀表存在的問題,參考當今國際先進水平,對鉆井參數的建模和測量方法進行了研究,並在此基礎上運用現場總線、客戶服務器等新技術研究開發了一套精度高、功能齊全、界面美觀友好的實時多參數鉆井監測系統。The advanced companies abroad in this field are m / d totco of usa, datalog of canada and rigserv of british. domestic companies are shenkai company hi shanghai, xushui instrument factory of cnpc, the third instrument factory of cnpc and chongqing instrument factory of cnpc. on a whole, the instruments of both home and foreign made can be unproved in working principals and methods
有關鉆井參數儀表的研究開發,國外比較著名的是美國的馬丁( m dtotco )公司、加拿大的datalog公司和英國的瑞設( rigserv )公司,國內主要有上海神開科技工程公司、徐水物探儀器廠、第三石油儀表廠和重慶石油儀器廠等。分享友人