鉗位電路 的英文怎麼說

中文拼音 [qiánwèidiànlù]
鉗位電路 英文
circuitry, clamping
  • 鉗 : Ⅰ名詞1 （鉗子） pincers; pliers; tongs 2 （姓氏） a surname Ⅱ動詞1 （夾住） grip （with pincers）...
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 路 : 1 （道路） road; way; path 2 （路程） journey; distance 3 （途徑; 門路） way; means 4 （條理） se...
  • 電路 : [訊] circuit （ckt）; electric circuit; electrocircuit電路板 circuit board; 電路保持 guard of a c...
  1. Based on the thorough investigation of the post - regulation and efficiency in multiple output switching - mode power supplies, an optimal combination topology for multiple output switching converter is presented in this thesis, which is consisted of forward converter with active clamp ( fac ), synchronous rectification ( sr ) techniques and magnetic amplifier technique ( magamp )

    本文通過研究分析近年來多路輸出開關電源輔助輸出電壓調節和提高效率的方案，面對開關電源朝著輸出低電壓大電流方向發展的趨勢，提出多路輸出開關電源新的拓撲優化組合模式? ?有源鉗位正激變換器、同步整流技術、磁放大器。
  2. Through instance and analyzing concrete data, the two ways of measuring insulation are introduced. the implementation of the method of clamping rundle circuit and its capability are described emphatically

    通過對實例和具體數據的分析，介紹了2種測量絕緣的方法，重點講述了鉗位電路梯級測量法的實現及其性能
  3. In this thesis, a clamp passive loseless snubber is put forward for igbt inverters after analysing the dissipation of hard switching and soft switching with snubber. then theoretical analysis and simulation are been take to prove the work of the snubber. and a real inverter circuit and its auxiliary circuits are built

    本文在對igbt在硬開關和有緩沖電路的軟開關情況下的開關損耗進行分析之後，提出一種適用於igbt逆變橋的鉗位式無源無損緩沖電路，然後進行了理論分析和模擬分析，並製作了實驗電路和相關輔助電路。
  4. Clamping diode circuit

    鉗位二極體電路
  5. However these converters become more complicate. phase - shift zvs technique has been used in bidirectional dc / dc converters since it can realize zvs for all switches without auxiliary switches. however when the amplitude of input voltage is not matched with that of output voltage, the current stresses and rms currents of the converters become higher, in addition the converters can not achieve zvs under light - load condition

    諧振、準諧振或多諧振技術方案，變換器的電壓電流應力較高，變頻控制增加了濾波器設計的難度；能量緩沖吸收電路或有源鉗位電路方案，由於需要增加多個額外輔助元件，增加了變換器的復雜性；全橋相移技術方案，由於主電路無需增加額外元件，只需利用相移控制，即可實現軟開關，因此引起關注。
  6. And methods of modification are proposed, which are mainly presented on clamping circuit and method of compensating for the errors of count results. thus the performance of system can get further improvement

    在測試過程中，發現了現有實現技術的某些不足，並有針對性的提出了改進，主要體現在計時電路中的鉗位電路設計和脈寬補償思想，有利於進一步改善系統性能。
  7. A clamp is used in some data sets to hold receiver output constant and avoid troublesome noise interference when no data signals are being received

    鉗位電路用於某些數據設備可使接收器輸出為常量，並且可在沒有收到數據信號時避免噪音干擾。
  8. Ac small signal model and the operating principle of forward converter with active clamp are analyzed in this paper. the superiority of fac is obtained by comparing three typical kinds of methods of magnetic reset for forward converters

    本文結合應用有源鉗位正激變換器，對有源鉗位正激變換器從電路的工作模式到小信號模型建立進行了深入的分析。
分享友人
分享到 Line

分享到臉書