鉸支座 的英文怎麼說
中文拼音 [jiǎozhīzuò]
鉸支座
英文
hinged support-
The parts and units of jigs and fixtures. hinger rest
機床夾具零件及部件.鉸鏈支座After an introduction to the research on the software for the design of the variant steel arched girder construction, the creation of the structural model, the structure of the supporting seat, the design of the variant arched girder, and the measures taken to ensure the stability of the plane surface of the arched girder, the thesis goes to study the methods for the hoisting and the angle setting of the long - span arched girders, as well as the bolting of the axle pin in the hinge support
論文首先對變異鋼拱架結構設計可採用的軟體、結構模型的建立、支座構造形式、變異拱梁的設計，以及保證拱梁平面外穩定所採取的措施等進行了研究，然後研究了大跨度變異鋼拱架弧形梁吊裝、角度的調整、鉸支座穿軸銷等的施工方法，最後對施工完成後的位移進行了實際量測。In this study, sts - - the steel construction design module of pkpm, a software program of china " s institute of the construction science - - is employed to create the construction model in order to study the construction of the supporting seat. a mechanical analysis of the variant arched girders was implemented, with the result that consturction documents meeting mechanical requirements were designed for the hinge support, the roller support and the steel girders
本文採用中國建築科學研究院pkpm軟體的鋼結構設計模塊sts ，從結構建模入手，根據規范要求研究了支座的構造形式，通過對變異拱梁的力學分析，設計出符合力學模型的鉸支座、滑移支座和變異拱處鋼梁的施工圖。In this paper, the construction method for the hinged steel bearings and hinged sliding plate bearings specially designed for the bridge is presented
介紹針對本橋專門設計的鉸軸鋼支座和鉸軸滑板鋼支座施工方法。Whether the axle pin can be smoothly bolted into the hinge support is crucial for the whole project. to achieve this goal, a prefabricated taper pin was used to induce the axle pin
鉸支座穿軸銷順利與否是施工的關鍵，採用提前做一錐銷來引導軸銷的方法來實現。The unique pacific tilting disc check valve internal disc hanger not only eliminates potential leakage through external hinge pins, but because the hanger shelf is machined parallel to the seating surface, it allows adjustment of the disc / seat if seat repair is ever required
獨特的美國太平洋翻轉式閥瓣止回閥內置閥瓣鉸鏈銷不但消除了穿透閥殼的鉸鏈銷可能出現的泄漏現象，而且由於經過機加工的支架平行於閥座表面，使得維修閥座時，能夠調整閥瓣/閥座。On the basis of simplified calculation model presented by doctor wangxiaoping, some finite element models are set up. by finite element model program sap93, an analysis of static models of 18m - span and 30m - span w666 acmr in different supporting conditions is made. also a study on the relation between definite support displacement, which reflect variational stiffness of substructure represented by steel column or reinforced concrete column, and load - carrying capacity mechanical performance is made too
本文以w666金屬拱型波紋屋頂為研究對象，沿用王小平博士的簡化計算模型，對18m 、 30m跨波紋拱兩端不同支座形式（鉸支、固支和彈性支座）分別利用有限元計算程序sap93進行計算分析，研究波紋拱在不同跨度，不同支座形式下，不同外荷載作用時對該結構受力性能及穩定承載力的影響，同時分析下部支承鋼柱、鋼筋混凝土柱的剛度變化體現為允許支座位移的大小與結構受力性能及穩定承載力之間的關系。As we know, support at the both straight edge of acmr is a elastic support between the hinged support and fixed support, and its stiffness is variational. so the relation between support stiffness and load - carrying capability of acmr is worth to be studied
眾所周知，實際工程中波紋拱兩端的直邊支座處于鉸支和固支之間，屬一彈性支座，其彈性剛度是變化的，支座剛度與波紋拱結構受力性能及穩定承載力之間的關系是一個非常值得研究的課題。分享友人