鋸工間 的英文怎麼說

中文拼音 [gōngjiān]
鋸工間 英文
sawing room
  • : Ⅰ名詞(拉開木料等的工具) saw Ⅱ動詞(用鋸拉) cut with a saw; saw
  • : Ⅰ名詞1 (工人和工人階級) worker; workman; the working class 2 (工作; 生產勞動) work; labour 3 ...
  • : 間Ⅰ名詞1 (中間) between; among 2 (一定的空間或時間里) with a definite time or space 3 (一間...
  1. Both the complicatedness varieties trees, the thick liquid material that the material differs greatly and the remaining leftover bits after wood processing, wood shaving, sawdust, sub thick liquid, cotton stalk, hemp stalk, bush, crudefiber crop, rice wheatgrass, reed, crudefiber crop, many kinds of goods thick liquid board, wasted paper, bagasse, agrimony etc. canbe fasten separated into the good fibre with higher velocity and proper to rub a block of interval

    高濃磨對漿料的適用范圍較廣,無論是樹種復雜,材料差異較大的漿料,還是木材加后剩餘的邊角料,以及蝕花、屑、節子漿、棉稈、麻稈、灌木、枝椏材、稻麥草、芳菲、麻類多種商品漿板、廢紙、甘蔗渣、龍須草等,都能夠以其料高的旋線速成度及適當磨片隙分離成優質纖維。
  2. He owns a workshop about 20 miles from company headquarters where he keeps three table saws, two lathes and a huge assortment of hand tools

    他在離公司總部20英里遠的地方擁有一處車,裏面有三臺臺、兩臺木車床和一大堆手動具。
  3. In the bamboo grove meditation area, fellow initiates first sawed off withered yellow bamboo to make room for young green bamboo shoots and allow sunlight to shine into the grove

    竹林打坐區的作部份,同修先將已經枯黃老死的竹子掉,讓新生的綠竹享有充分舒展的空,同時陽光也得以照進竹林。
  4. Suspension construction method : use saws to cut the plywood 9 c 12mm thick into square blocks sized between 600 c 120 mm and securely nail them into the concrete ground at an interval of 20 mm

    步驟3 :墊層鋪設1懸浮施法:將9mm - 12mm厚的夾板成600mm - 120mm的方塊隔20mm釘牢水泥地面。
  5. A moment afterwards, and a throng of people came pouring round the corner by the prison wall, in the midst of whom was the wood - sawyer hand in hand with the vengeance

    頃刻,一大群人從監獄墻角轉出,也在其中,他跟復仇女神手牽著手。
  6. 3, bolivia magnesium boards use : bolivia magnesium board is the most fundamental of intermediate materials, subject to surface decoration before official use, promote magnesium boards with the use of wood plate of the same methods can be adopted sawn, no, nails, machining, manufacturing of decorative works of the structure, and through the face decorated rujiaoqi, wallpaper, ceramic tiles use waterproof type gypsum board do finishes, complete decorative works

    3玻鎂板的使用:玻鎂板是最基本的中材料,須經過表面裝飾后才能正式使用,所以玻鎂板的使用同木材板材的方法相同,可以通過刨釘等加藝,製成各種裝飾作品的結構,再通過面飾乳膠漆壁紙陶瓷墻磚要用防水型石膏板做終飾,完成裝飾程。
  7. By the experiments on sawtooth anti - blocking mechanism under different situations. pictures analysis shows that anti - blocking capability is excellent when the rotary speed of main shaft is 650 r / min, the trolley speed is 0. 3 m / s, he interval between moved, sutter and static cutter and the mulehed straw is 10mm and the mulrhed straw is 11250 kg / hm2

    利用該測試系統對齒防堵裝置在不同況下的防堵性能進行了定性分析,分析結果表明:轉速為650r min 、臺車前進速度為0 . 3m s 、動定刀隙為10mm 、秸稈覆蓋量為11250kg hm ~ 2時,防堵效果比較好。
  8. And relying on this, our laboratory proposes a new cladding method. by means of large dynamic explicit fem code ansys / ls - dyna, the numerical simulation was carried out in bimetal forming process. during the simulation of the forming process, the large deformation of the strip should be considered, as well as geometrical and material nonlinear, the contact between the roller and the strip, the contact between two metal sheets and the load. as for these problems, we can use node to surface contact and relative parameters, biso model is introduced, the load is applied as array

    本文採用ansys / ls - dyna計算程序為分析具,對齒形雙金屬復合板成型過程進行計算機數值模擬,在對軋制過程模擬時,針對軋件變形的幾何非線性和材料非線性特點、軋輥與軋件的接觸、軋件的接觸以及模型的加載等問題,給出了在ansys / ls - dyna中相應的解決方法:應用nodetosurface接觸方式,設定相應參數,選用雙線性等向硬化模型,載荷作為array施加在剛體質心。
  9. For sharpening mill saws and various cutting tools as a general purpose file for shop floor workings

    主要是為了削尖磨和不同類型的切割具,作為車作的一個通用銼刀。
  10. Abstract : a research has been carried out theoretically and experimentally on the relationships among the unit volume fragmenting power of the diamond - circular saw and the factors such as grain sizes, concentration and working clearnce

    文摘:從理論和實踐上研究孕鑲金剛石圓片的單位體積破碎功與金剛石的粒徑、濃度及隙等因素的關系。
分享友人