鋼板模板 的英文怎麼說

中文拼音 [gāngbǎnmóbǎn]
鋼板模板 英文
sheet steel form
  • 鋼 : 鋼名詞（鐵和碳的合金） steel
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 鋼板 : [冶金學]1 （板狀鋼材） steel plate; nickelclad steel sheet; plate 2 （汽車上的片狀彈簧） spring3 ...
  • 模板 : [土] formwork; mould; shuttering; follow board; form board; match board; match plate; mother plat...
  1. The approximation analysis result of band dipole model is obtained on the basis of the theory of mfl. the electromagnetic distribution feature of the defect in the steel panel is studied by means of simulation. the leakage magnetic distribution of the two defects and four defects plural and the defects in the column differently in the width are also assayed. conclusions that factors affecting flaw magnetic leakage to the panel also affect the column and magnetic leakage bx should be the feature of the flaw identification to several flaws are drawn

    在對漏磁檢測原理進行詳細介紹的基礎上，得出了帶偶極子模型的近似解析解，並以有限元數值模擬分析為主要手段，以鋼板上缺陷為對象，分析了各因素對缺陷漏磁場產生影響的不同規律，同時模擬分析了板上平行的兩條裂紋，四條裂紋以及柱體上寬度不同時的裂紋的漏磁場分佈特徵，得出結論:影響板上缺陷漏磁場的諸因素會對柱體上缺陷漏磁場產生同樣的影響;對于多條裂紋，宜用漏磁分量bx作為缺陷識別的特徵量。
  2. Reduce the use of timber by using alternative structural solutions ( e. g. metal hoarding, system form - work, metal form - work, semi - pre - cast flooring system, pre - cast roofing, dry walls and other structural means such as steel structural section, left - in formwork, etc. )

    改用其他結構方案（例如金屬圍板、標準化模板、金屬模板、半預制樓板系統、預制天面、干墻及其他結構措施，如鋼造結構架和內留的模板等） ，藉此減少使用木材
  3. Technical specification for plywood form with steel frame

    鋼框膠合板模板技術規程
  4. Adopting the construction scheme which combines iron - frame moulded board with unsegragating concrete underwater and encircling steel hoop on glass fiber reinforced plastic mortar pipes, the difficulty in construction of outfall in riprap mound within a short period period is overcome

    摘要通過採用鋼框模板結合水下不離析混凝土以及對玻璃鋼夾砂排水管採用抱箍的施工方案，成功解決了在較短工期內完成拋石棱體中出水口施工難度大的問題。
  5. Pulp, boxes, frames, general construction, woodwoking ( flooring, siding, ceiling, doors, blinds, etc. ), airplanes, musical istruments ( especially sounding boards of pianos ), cabinets, ships, railroad coaches, furniture, wares, kegs and ladders

    紙漿材、箱盒材、線條、地板、天花板、木門、窗? 、模型飛機、樂器構造材（如鋼琴響板） 、櫥櫃、造船材、傢俱等。
  6. Equipment for steelworks and rolling mills ; shuttering steeves for anchor boxes according to din 24539 ; dimensions, designation

    煉鋼廠和軋鋼機用設備.按din24539的錨盒的模板吊桿
  7. A die plate for flattening metal into strips, as in the manufacture of watch springs

    扁條拉模一種用來拉平鋼條的模板，如用於生產手錶發條的模板
  8. The paper introduces the construction technique and quality control of the concrete ground container, the project uses the small machine - constructing method which vibrates beam and the vibrating spear unify, through example of key working procedure : the construction survey, the ground basic roller compaction, two ash zone constructions, the steel bar construction, the template construction, the concrete surface layer construction craft and the quality control, the small machine construction method prove to meet the project needs

    摘要介紹了混凝土集裝箱堆場施工工藝與質量控制，工程採用振動梁和振動棒相結合的小型機械法施工，通過對關鍵工序如：施工測量、場區基層碾壓、二灰層施工、鋼筋施工、模板施工、混凝土面層的施工工藝與質量控制，表明小型機械法施工能滿足工程需要，工程完成後符合驗收標準，滿足了業主的使用要求，對于同類工程的施工具有借鑒意義。
  9. To avoid manual labor of chiseling - grossness, in the area of second - stage concrete construction, permanently non - removed metal molding boards nets are used as molding boards of first - stage concrete. substitution joints of reinforcing steel bars for traditional electric welding and usage of equipments for joints of reinforcing steel bars efficiently improve strength of junctions and rate of connecting reinforcing steel bars, and safety of construction and stability of quality, and greatly reduce cost. it ' s possible that three gorges project become top - ranking project in the world by study on systems engineering of high - strength concrete construction

    混凝土縫面處理採用高壓水流沖毛技術，大大提高了施工工效，減少了倉面污染；模板工程大量採用定型鋼模板施工技術，提高了壩體混凝土成型質量和工程進度；在二期混凝土施工區域，為免除人工鑿毛勞動強度，採用永久性免拆金屬模板網作為一期混凝土模板；鋼筋連接改進傳統的電焊連接方式，採用大量採用鋼筋接頭機械連接技術，有效提高了接頭強度和鋼筋連接速度，施工安全性大大加強，質量穩定性有效提高，經濟成本大大降低；三峽二期工程持續高強度混凝土施工系統工程的研究，使三峽工程成為名符其實的「世界一流工程」成為可能；三峽二期工程混凝土溫控綜合技術的應用，有效降低了壩體混凝土溫度的產生；混凝土表面處理及裂縫處理技術的應用，提高了建築物的整體性和耐久性。
  10. Based on tests of nine 1 / 2 - scaled model slabs under vertical loads, the paper analyzed load - deformation curve and proposed limit value of height - width ratio under axial loads. 2. based on aseismic tests, the paper put forward a model of concrete frame, silica brick and a combination of the two, proposed that the silica brick works as a 45 compression bar, analyzed the factors which may influence bearing capacity of the slab and advised a formula including the numbers of bays and of storeys of the frame

    通過對墻板模型的抗震性能試驗研究，建立了由鋼筋混凝土框格、砌塊以及兩者協同作用三個部分組成的承載力極限狀態下的理論簡化計算模型；提出了墻板中填充塊等效斜壓桿寬度按45度計算的統一量化標準；分析了影響墻板承載力的主要影響因素，給出了表達墻板框格層數和跨數不同的斜截面承載力實用設計計算公式。
  11. This paper focuses on the research of the stress mechanism of the ribbed shell structure in statics, dynamics and under the explosive load on the basis of the engineering practice of cave depot of single aircraft. in this paper, according to the classical shell theories, the basic differential equilibrium of the ribbed shell structure and the finite element analysis of 3d rippled plate are established, in which the function of annular ribs reinforcement bars and 3d ripped steel plates are distributed in the range of the steel, and the functions along the longitude direction of tension, bending, and torsion are neglected ; applied with dynamic analytical theory, the dynamic model of ribbed shell structure and the analytical theory model of elastic - plastic are set up ; the triangle series method is used to solve the displacement and stress under the distributed load and the concentrated load of the ribbed shell structure

    本文以軍用機場地面單機掩蔽庫工程建設為工程背景，首次對內襯三維波紋鋼板混凝土拱型復合結構的受力機理進行了靜力、動力和爆炸荷載的分析研究。根據將橫肋、鋼筋及三維波紋鋼板的作用均勻分佈在殼體范圍內的情況，忽略橫肋、鋼筋及三維波紋鋼板沿殼體母線方向的抗拉、抗彎及其抗扭作用，首次推導出了內襯三維波紋鋼板混凝土殼體的微分平衡方程，建立了有限元計算模型，並採用三角函數法，求解了三維波紋鋼板混凝土拱型復合結構在分佈荷載和集中荷載作用下的位移響應和應力響應，並與普通殼體進行了比較。
  12. In this paper at last. the localized anti - collapsing effect of the cave depot of single aircraft under the explosive load is calculated and analyzed. the explosive result shows that 3d ripped steel plate and ribbed shell structure are effective to raise the capacity of anti - collapsing of the protective structures

    對飛機單機掩蔽庫工程在爆炸荷載作用下，抗局部震塌效應進行了計算分析，模擬直接命中的爆炸試驗結果表明：鋼筋混凝土內襯三維波紋鋼板組成拱型復合結構，是提高防護結構抗震塌破壞的一種十分有效的措施。
  13. Simulation of the shape control characteristics of 4 - high cvc hot steel strip mill

    熱帶鋼軋機板形控制特性的模擬
  14. Experiments and numerical simulation of dynamic cool - down process of stainless steel plate in liquid nitrogen bath

    液氮浴中不銹鋼板動態冷卻過程試驗及模擬分析
  15. Through analyzing the structure of open caisson, and according to sinking stress principle, the paper introduced in the open caisson construction process sinking, correcting error, survey control as well as peculiar circumstance processing technical measure, such as in open caisson construction the inner - mold for sanding, framework supporting and steel binding, and concrete casting ; in open caisson sinking - control the sand in edge foot inner - mold, sand - pumping sinking, and pressure hydraulic monitor breaking and pressure - blowing sinking by air pressure blower etc

    摘要根據下沉受力原理，分析了沉井結構，介紹了沉井施工過程中的下沉、糾偏、測量控制以及特殊情況處理的技術措施，如沉井製作中的填沙內模，模板支設和鋼筋綁扎，混凝土澆注；沉井下沉控制中的刃腳內模沙土，抽沙泵抽沙下沉，高壓水槍破壓、空壓機吹壓下沉等。
  16. Vertical transportation : reinforcing steel bar, from and so on materials should use self - lifting tower crane and one 50t crawler crane

    垂直運輸：鋼筋、模板等材料使用自升式塔式起重機，並配備一臺50t履帶式起重機。
  17. The riveting and welding plant of the company has a very strong technical force, the technical personnel makes up more than 1 3 of the total staff, the company can also undertake the manufacture of various metallurgical structural equipment, formwork, gang board, oil tank, water tank, pipeline and dust - collecting and environmental protection equipment of various sizes, the company also undertakes the construction of bridge, concrete building as well as underwater and high - altitude operations from omniberaing etc. no matter what sizes and shapes of the forging and casting spare parts including special - shaped parts, we will never refuse you and promise to satisfy you with best quality and finish the task on schedule

    公司鉚焊廠，技術力量十分雄厚，工程技術人員，佔全體員工的三分之一以上，可以承攬加工各種金屬結構設備模板跳板油罐水罐管道工程各種型號除塵環保設備，再如橋梁鋼筋混凝土建築，水下高空全方位作業等，除些之外，關于鑄造鍛造等工作不論大，中，小型部件，也能做到來而不拒，保證，保質，保量按期完成任務。
  18. In the construction of the tanghe inverted siphon on mid - roule of south - to - north water transfer project, some reliable construction processes and techniques are applied such as belt conveyor with three - rail gantry, construction with combined steel formwork, straight screw sleeve connection for reinforcement and the crushed stone - planting method etc., by which better construction effects are obtained

    摘要南水北調中線唐河倒虹吸工程項目施工中，根據工程特點，採用了三軌門架式皮帶布料機、鋼模板聯體施工、鋼筋滾壓直螺紋套筒連接、混凝土施工縫栽石法等可靠的施工技術和施工工藝，取得了較好的效果。
  19. Plybamboo form with steel frame

    鋼框竹膠合板模板
  20. Iron and steel. three - layer steel strips for mould boards. prescriptions

    鋼鐵.模板用的三聯鋼帶.質量要求
分享友人
分享到 Line

分享到臉書