鋼板殼體 的英文怎麼說
中文拼音 [gāngbǎnkétǐ]
鋼板殼體
英文
sheet steel housing-
The fem analysis for the three structures of sling screw - thread - based, namely the circle, rectangle and that with strengthen plate, and the tensile test for sling screw - thread - based in torpedo body show, that the bonding with strengthen frp plate between load - bearing metal parts and frp hull with hatch can reduce the stress concentration and significantly decline the local stress in frp hull with hatch. this structure can also be used in the similar produces. ( 3 ) the effects of parameters for bonding process on the adhesive strength and leakproof are discussed, such as the bonding interface reduce, bonding surface treatment, match of adhesive surface, protect for adhesive seam and so on
本文通過某型號雷體吊耳螺紋座結構的三種方案，即圓形昂耳螺紋座、長方形吊耳螺紋座、具有增強板的吊耳螺紋座的有限元分析及雷體吊耳螺紋座拉力試驗結果證明：金屬承力件與開口玻璃鋼殼體粘接採用玻璃鋼增強板補強，緩和了應力集中，使開口殼體局部應力明顯降低，類似的水下兵器用金屬承力件與開口復合材料殼體膠接均可採用此種結構形式。This paper focuses on the research of the stress mechanism of the ribbed shell structure in statics, dynamics and under the explosive load on the basis of the engineering practice of cave depot of single aircraft. in this paper, according to the classical shell theories, the basic differential equilibrium of the ribbed shell structure and the finite element analysis of 3d rippled plate are established, in which the function of annular ribs reinforcement bars and 3d ripped steel plates are distributed in the range of the steel, and the functions along the longitude direction of tension, bending, and torsion are neglected ; applied with dynamic analytical theory, the dynamic model of ribbed shell structure and the analytical theory model of elastic - plastic are set up ; the triangle series method is used to solve the displacement and stress under the distributed load and the concentrated load of the ribbed shell structure
本文以軍用機場地面單機掩蔽庫工程建設為工程背景，首次對內襯三維波紋鋼板混凝土拱型復合結構的受力機理進行了靜力、動力和爆炸荷載的分析研究。根據將橫肋、鋼筋及三維波紋鋼板的作用均勻分佈在殼體范圍內的情況，忽略橫肋、鋼筋及三維波紋鋼板沿殼體母線方向的抗拉、抗彎及其抗扭作用，首次推導出了內襯三維波紋鋼板混凝土殼體的微分平衡方程，建立了有限元計算模型，並採用三角函數法，求解了三維波紋鋼板混凝土拱型復合結構在分佈荷載和集中荷載作用下的位移響應和應力響應，並與普通殼體進行了比較。Non - pollution, the pump body is made of polyvinyl chloride ( pvc ) plastics, and the onter cover is of cold - rolled steel plate with backing finish
無污染，本機箱體為聚氯乙稀塑料，外殼採用不銹鋼和冷板靜電噴塑殼兩種。According to the theory of the finite element analysis, the matrix of mass, rigidity and damp in every part of shell structure have been fixed on ; at the same time, calculation has been done in dynamics and statics
利用有限元理論，分別確定了復合殼體結構中各部件的質量矩陣、剛度矩陣及阻尼矩陣，並對其進行了靜力學與動力學計算，結果證明內襯三維波紋鋼板復合殼體結構與普通混凝土殼體結構相比，其結構承載力有了較大的提高。The shell parts of reactor pressure vessels have been often fabricated with formed plates welded together, especially in usa and japan
反應壓力容器的殼體，歷來常常是用成型鋼板焊接而成的，在美國和日本尤其如此。The steam leakage was occurred on the welding zone of the tube sheet of the austenitic stainless steel heat exchanger
摘要在奧氏體不銹鋼制再沸器的上管板與殼程筒體焊接的管板一側發生蒸氣泄漏。分享友人