錐場法 的英文怎麼說
中文拼音 [zhuīchǎngfǎ]
錐場法
英文
cone-field method-
In view of bearing capacity of the elastoplastic theory analysis, the author made a comparison between the achieved bearing capacity limit load pi / 4 of round base ( space problem ) and the limit load pi / 4 of bar groundwork foundation design ( plane problem ) from soil mechanics at home and abroad as well as foundation criterion, and explained why the value of formula in present design criterion from soil mechanics is inclined to be conservative. in the light of the author ' s many years experience of vibration test on the spot and the research work of relevant projects, the author worked over the dynamic pile testing of the bearing capacity of foundation and batholith, and gathered the parameter of dynamic analysis and testing. the author also talked over the difficult point of pile foundation design criteria in present batholith engineering world, i. e. the confirmation of batholith bearing capacity of pile end, from the following aspects : a ) confirmation of single axis counter - pressure strength of rock in house ; b ) f. e. m calculation of elastoplastic model ; c ) calculation of soil mechanics ; d ) deep well load test
然後，對巖土工程領域至今尚未解決，甚至不為人注意的考慮地基變形的地基承載力問題進行了實用化的探討，提出了考慮地基變形的地基承載力上程計算方法；對基於彈塑性理論分析的地基承載力國內尚未見報道的空間問題得到了圓形基礎（空間問題）的承載力界限荷載p _ （ 1 / 4 ） ，並與國內外土力學專著及地基基礎設計規范中的條形基礎（平面問題）的界限荷載p _ （ 1 / 4 ） ，進行了對比，從而定量上解釋了目前設計規范引用土力學承載力公式值偏於保守的這一情況；根據本文作者多年從事現場地基工程振動試驗及相關課題的研究工作，本文以截頭錐模型模擬地基，對地基（巖基）承載力的動測法進行了研究，為各類地基（包括巖基） ，匯總了動力分析和檢測川的參數：針對日前巖土工程界應用樁基設計規范中的難點? ?樁端巖基承載力的確定問題，從巖石室內單軸抗壓強度確定、基於彈塑性模型的有限單元法計算、土力學計算及深斤載荷試驗四方面進行了深入討論；本文作者根據多年現場載荷試驗的工程實踐，對深井荷試驗裝置的核心部分? ?反力裝置，設計了側壁支撐反力加載系統，該加載系統具有實用、簡便、穩定及安個等優點。With the use of finite method we have developed computer simulation software for vacuum microtriodes with wedge - shaped and cone - shaped cathode on the basis of stduying deeply the field emission theory of vacuum microelectronics. the software included field section, grid point numbering, and the calculation of electric currents, transconductance and cathode capacitance, moreover, it can simulate the properties of vacuum microeletronic with variant structures and sizes. the relationship was studied and simulated among electic properties and device structures, sizes and cathode materials etc. the optimized design of vacuum microtiode was proposed
本文在深入研究真空微電子器件場致發射理論的基礎上，根據圓錐形、楔形陰極真空微電子三極體的不同特點，分別建立了物理和數學模型，在考慮空間電荷密度影響的前提下，以有限元法為基礎採用迭代的方法計算出真空微電子三極體內的電勢分佈情況，繪制出了等勢線、電子軌跡線，並得到了器件電學性能隨幾何參數的變化情況。In order to open the cover of a concentric canister launcher ( ccl ) automatically with the jet during its launching, four schemes are put forward, viz. fracturable cover, eccentrically positioned interior and exterior launching tubes, jet guides of assymmetric construction, and covers made of heterogeneous materials
摘要為實現導彈自力發射時同心發射筒前蓋自動向一側開啟，討論了4種燃氣開蓋方案：易碎蓋方案、內外筒偏心蓋方案、半導流錐方案和各向異性材料發射筒蓋方案，並用數值方法模擬了各種方案的筒內復雜三維流場。( 2 ) the causation that the caustic phenomena of electromagnetic wave propagation in two - dimension concave reflectors occurs and the types of singularities in caustic fields are investigated, and the conclusion that there are two types of singularities ( fold and cusp ) in caustic fields in two - dimension concave reflectors is obtained ; by symplectic geometrical method, formulations of computing wave fields in and far away from caustic fields in two - dimension concave reflectors are deduced, and the results are plotted in pictures. ( 3 ) the cause of the caustic phenomena of electromagnetic wave propagation in three - dimension concave reflectors and the types of singularities in caustic fields is discussed, and the conclusion that there are three main types of singularities ( fold, cusp and swallowtail ) in caustic fields in three - dimension concave reflectors is obtained ; by symplectic geometrical method, the formulae of computing wave fields in and far away from caustic fields in three - dimension concave reflectors are deduced. particularly, the wave fields in ellipsoid concave reflector are computed, and the results displayed in special sections are given
論文主要包括三個方面： （ 1 ）分析了凹面反射的焦散現象，給出了不同凹面反射的焦散圖； （ 2 ）分析了二維凹面反射波動場焦散現象產生的原因及焦散區奇性的種類，得出了二維凹面反射波動場焦散區奇性主要有折疊（ fold ）和尖點（ cusp ）兩種的結論，利用辛幾何方法構造了圓錐曲面反射波動場非焦散區和焦散區的通用計算公式，並給出了圓柱面、橢圓柱面及雙曲柱面反射的計算結果； （ 3 ）分析了三維凹面反射波動場焦散現象產生的原因及焦散區奇性的種類，得出了三維凹面反射波動場焦散區奇性主要有折疊（ fom 、尖點kusp和燕尾k ）三種的結論，提出了利用辛幾何方法計算三維凹面反射波動場非焦散區和焦散區的計算方法，並給出了三軸不等橢球體凹面反射波動場的計算結果剖面圖。We present a calculation program in this paper, based on the physical optical theory ( po ) theary to predict bse and bses for a conical type of radome. the po theory is used to determine the ficticius currents electrical and magnetic on the inner face of the radome, which is illuminated directly by the radar antenna, and then use the transmission matrix mothod to determine the outer surface ficticion currents, the radiated from the antenna through radome is considered as the radiation field of these ficticion current
本文提出了一種基於物理光學理論預測正圓錐天線罩瞄準誤差及瞄準誤差斜率的計算程序。首先，雷達天線照射到天線罩內壁，應用物理光學法求出內壁等效的電流和磁流，其次，根據傳輸矩陣理論求出外壁等效電流和磁流，天線通過天線罩的遠區場即可認為是外壁等效電、磁流產生的場。A large number of attempt and painstaking experiment have been done in this paper according to existing project. we also do lots of chemical and electrochemical etching research in material of lab6, and find out three kind of methods to produce the field emitting cold cathode including reactive ion etching ( rie ) with oxygen, wet process etching and electrochemical etching. through produce some field emitting cold cathode single tip including lab6 field emitting cold cathode, molybdenum field emitting cold cathode, tungsten field emitting cold cathode, tungsten rhenium field emitting cold cathode, molybdenum covered with lab6 film field emitting cold cathode
而且，目前可借鑒的參考文獻較少，圍繞著前人做過的方案，本文做了大量工作，在已有文獻介紹的基礎上，結合原有的理論和實踐基礎，摸索出了包括高溫氧作用反應離子（ rie ）刻蝕法、濕法腐蝕法和電化學腐蝕法在內的三種制備工藝，運用電化學腐蝕工藝成功制備了單尖的六硼化鑭場發射冷陰極尖錐、鉬場發射冷陰極尖錐、鎢場發射冷陰極尖錐、鎢錸合金場發射冷陰極尖錐以及有六硼化鑭薄膜覆蓋的鉬場發射冷陰極尖錐。It suggests not to use shut - in coning control method to deal with water coning effect
建議礦場上不要採用關井壓錐的方法來克服底水錐進帶來的不利影響。Measurement of gas flow is a difficulty. v - cone flowmeter provided a new measuring method for measurement of gas flow. application and feature of v - cone flowmeter are introduced
摘要煤氣流量測量一直是儀表檢測的難點，錐型流量計為煤氣流量測量提供了新的測量方法，本文介紹了錐型流量計在現場的使用情況和特點。This text completely and systematically studies the status and the development of the pyrolysis and the fluidization of biomass, which distill the bio - oil in the domestic and international area, as well as the existing problems. this thesis primarily include following aspects : ( l ), by experimenting and measuring the energy ( heat value ) and the content of c, h, n chemical element of right 20 kinds of common biomass, on the base of the experimental result, and respectively established the biomass energy predict experiment formula with the element of h and c is from change, and passed the ro. os examination, which provides the basis and convenience for flash pyrolysis fluidization device energy to convert the rate to compute with biomass energy utilization calculation ; ( 2 ), proceeded the tg and dtg experimentation equal velocity ( 10 ? / min, 20 ? / min, 40 ? / min, 60 ? / min ) heating and constant temperature heating by studying on eight kinds of biomass samples, according to the experimental data and arrhenius formula, we established the dynamics model of pyrolysis of, then, using the goast - redfern and p function, we also solved the dynamics parameters and analyze out every kind of biomass ' s frequency factor and parameters of activation energy, and established the every kind of dynamics model of pyrolysis of biomass, all of these provide the theories and basis to make sure the reactor ' s flash pyrolysis work temperature scope design and the describing of pyrolysis reactor dynamics ; ( 3 ), in order to study and ascertain the process of heat completely getting to pyrolysis time of varied size biomass particles, we observed and measured the ratio of length and diameter ( l / d ) with the varied biomass through electron microscope, we concluded the l / d ratios usually is from 5. 0 to 6. 0, the average is 5. 3 ; ( 4 ), we studied the process of biomass transiting and the theory of complete pyrolysis time with the theory of complicated heat field, we got the time ( t ) of the varied size biomass particles arriving to complete pyrolysis, and we knew that the complete pyrolysis time and the time which get to the biggest production ratio are identical, all of these studies provide the theory base for design and forecasting the flash pyrolysis reactor solid state resort time ; ( 5 ), according to the above experiment result, synthesize to make use of the engineering the mechanics, engineering the material, machine the design to learn the principle, deduce, establish the theory of rotation cone flash pyrolysis reactor material resort time ( t ) and reasonable rotation velocity ( or frequency ) relation theory ; and ( 6 ), we gave the reactor ' s smallest cone angle certain, reactor cone wall strength design theory, the reactor production ability theory, the power design method and the critical rotation velocity theory
本文較全面、系統地綜述了國內外生物質熱解液化制取生物燃油技術研究發展現狀及存在的問題，主要研究內容有： （ 1 ）實驗、測定了20種常見生物質的能量（發熱量）和c 、 h 、 n元素含量，根據實驗結果分別建立了以h和c為自變量的生物質能量預測經驗公式，並通過r _ （ 0 . 05 ）檢驗；為閃速熱解液化裝置能量轉化率計算和生物質能量利用率計算提供了依據和方便； （ 2 ）選擇了8種生物質試樣作了等加熱速率（ 10 min 、 20 min 、 40 min 、 60 min ）和恆溫加熱的tg和dtg實驗，根據實驗數據和阿倫尼烏斯公式建立了生物質熱解反應動力學微分方程，並採用goast - redfem積分法和p函數對其動力學參數進行了求解，解析出各種生物質的頻率因子和活化能參數，進而建立了各種生物質的熱解動力學模型，為科學確定反應器的閃速熱解工作溫度范圍及熱解反應動力學描述，提供了理論和依據； （ 3 ）為研究和確定不同尺度的生物質顆粒中心達到全熱解的時間，在體視顯微鏡下對不同粒度的生物質顆粒的長徑比進行了實驗觀察和測定，得出生物質的長徑比（ l d ）一般在5 . 0 6 . 0之間，平均為5 . 3的結果； （ 4 ）採用復雜溫度場傳熱學理論對生物質傳熱過程及充分熱解時間理論進行了研究，解析推導出了不同尺寸生物質顆粒中心溫度達到充分熱解溫度的時間（ t ） ，得出了理論推導的充分熱解時間與最大產油率的熱解時間相一致的結果，為閃速熱解反應器固相滯留時間設計和預測提供了理論依據； （ 5 ）根據上述實驗結果，綜合運用工程力學、工程材料、機械設計學原理，推導、建立了轉錐式閃速熱解反應器物料滯留時間（ ）與轉速（或頻率）合理匹配理論； （ 6 ）提出了轉錐式閃速熱解反應器的最小錐角設計、錐壁強度設計、生產能力設計理論和功率計算方法及臨界轉速理論等。Standard test method for density and unit weight of soil in place by the sand - cone method
用砂錐法現場測定土壤密度和單位重量的標準試驗方法In the paper, we put forward the combination of micro electronic technology, mems technology and vacuum micro electronic technology to develop a micro electronic pressure sensor with overload protection. the pressure sensor consists. of elastic anode membrane, isolation layer, vacuum micro cavity and field emission catelectrode tip array with overload protection. such pressure sensor has many advantages, such as high temperature stability, radiation resistance, fast response, high sensitivity, small volume, simple secondary instruments and bulk production
本文在重慶市科技「十五」項目的資助下，提出利用微電子技術、 mems技術和真空電子技術相結合的方法，研究一種帶過保護功能的真空微電子壓力傳感器，該壓力傳感器由帶過保護的場致發射陰極錐尖陣列、彈性陽極膜、絕緣層、真空微腔所構成，具有溫度穩定性好、抗輻射、快響應、高靈敏、體積小、二次儀表簡單、可批量生產等優點，具有廣泛的應用市場。2 for the first time, the author brings forward the concept of " pyramid horn high order mode resonator " and pml - fdtd technique is used to analyze the electromagnetic field distribution in the pyramid horn. the results show that the pyramid horn sensor is much more sensitive than the open ended waveguide or transmission line sensors. the sensor we used is a kind of resonance sensor
二、首次提出了「角錐喇叭高次模諧振腔」的概念，並且採用pml ? fdtd法分析了角錐喇叭場分佈狀態，從而，得出了角錐喇叭探頭比終端開口波導或傳輸線探頭靈敏得多的原因在於：我們採用的探頭是諧振式探頭，消聲瓦樣品的差別相當于對角錐諧振腔的微擾；採用波導或同軸線探頭，消聲瓦樣品的差別相當于對傳輸線終端負載有一點變化而已。Firstly, the paper introduces the development and application of computer graphics & image technique, discusses the principle and method of cg and digital image processing, such as matrix of the graphic transformation, homogeneous reference frame, sampling and quantization of the image, file format of the image, template operation, etc. secondly the paper introduces the purpose and method of image enhancement processing, explains the each occasion of those methods such as threshold transformation, smoothing processing, sharpening processing, analyzes and contrasts the processing results of object image. thirdly, the paper introduces the method of mathematics morphologic, edge detection and thinning processing, attains character description of image and character dots of the contour. fourthly, the paper processes the coordinate transformation to character dots and basic splines fitting, imports correlative condition to devise meshing line and meshing track
本文首先介紹了計算機圖形圖像技術的發展與應用情況，對計算機圖形學和數字圖像處理的一些基本理論和方法如圖形變換矩陣、齊次坐標系、圖像采樣和量化、圖像文件格式、模板操作等內容進行了討論：然後對圖像增強處理的目的和方法進行了介紹，對諸如閥值變換、平滑處理、銳化處理等方法的應用場合進行了說明，並對實物圖像的處理結果進行了分析與比較；接下來介紹了數學形態學方法、對增強后的圖像進行邊緣檢測的方法和圖像的特徵描述方法，並獲取輪廓的特徵點：隨后對獲取的特徵點進行坐標變換，並進行b樣條曲線擬合，引入相關條件生成齒輪副的嚙合線及嚙合軌跡：最後引入等值線和區域填充表示方法，並以等值線和區域填充的形式對弧齒錐齒輪嚙合模擬的載荷分佈情況進行了直觀的表示。Starting with analysis on the field of gaussian feed ' s aperture, the relations of radiation characteristic and power capacity and gaussian beam waist radius are investigated particularly by using the circular waveguide intrinsic mode expansion method
=本文從圓錐高斯饋源口面場分析入手，利用高斯場展開成規則圓波導場的方法，細致的討論了高斯束腰對饋源輻射特性和功率容量的影響。For the coupling between the laser diode and the tapered single - mode fiber, the overlap integral is used to compute the coupling efficiency on the basis that the laser diode outputting mode field and the fiber eigenmode field is approximated to basic - mode gauss field. and based on the same approximation, the coupling efficiency between the semi - tapered fiber and the laser diode is calculated by using the ray - traced method. the parameters are analyzed for the effect on the coupling efficiency and give the theory foundation to optimize the design of the tapered fiber coupling system
首先通過對半導體激光器輸出模式場和光纖本徵模式場的高斯基模近似，利用交疊積分計算了錐形單模光纖與激光器的耦合效率問題；其次依據以上近似，利用光線跡蹤法計算了半錐形多模光纖與激光器的耦合效率問題，給出各個參數對耦合效率的影響和作用，為優化設計錐形光纖耦合系統提供了理論依據。分享友人