錐形接觸 的英文怎麼說

中文拼音 [zhuīxíngjiēchù]
錐形接觸 英文
conical contact
  • 錐 : Ⅰ名詞1. （錐子） awl2. （似錐物） awl-shaped things 3. （錐體） cone Ⅱ動詞（鉆） drill; bore
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 錐形 : [機械工程] taper; cone; cone-shape
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  1. Established the system of coordinates of roll testing, getting the parameters of equation of tooth face by solving the non - linear equations set ; according to the differential geometry and meshing principle, deduce the curvature parameters of tooth face and tooth profile, and get the parameters of instantaneous contact ellipse. emulate the contact trace and contact area of the working tooth face, and drawing the instantaneous drive ratio error curve

    建立了克林貝格擺線齒錐齒輪嚙合分析的對滾模型，通過對非線性方程組的迭代求解，得到齒面方程的各個參數;由微分幾何和切齒嚙合原理推導了齒面上齒廓和齒線方向的曲率參數，得到了瞬時接觸橢圓的參數。根據設計參數和機床調整參數繪制了工作齒面的接觸軌跡和接觸區圖形，並求得了瞬時傳動比的誤差曲線。
  2. Hollow taper interface with flange contact surface - receivers - dimensions

    帶法蘭接觸面的空心錐形界面.接合器.尺寸
  3. Optional disc configuration which provides line contact between spherical disc and conical body seat

    備選閥瓣結構，在球形閥瓣和錐體閥座之間具有線接觸作用。
  4. Hollow taper shanks with flat contact surface - part 5 : hollow taper shanks type e ; dimensions

    帶扁平接觸面的錐形空心柄.第5部分: e型錐形空心柄.尺
  5. Current nod external nomal method can accurately solve the initial clearance of contact curved surface. the accurate analysis of load distribution, longitudinal load dispersion and contact patterns to spiral bevel gears has been deduced, and that the variation of the contact center of loaded spiral bevel gears and the contact center of non - loaded spiral bevel gears has been analysed

    當前節點外法矢法可以精確計算接觸曲面的初始間隙量，本文用這一方法對螺旋錐齒輪齒間載荷分配、齒向載荷分佈以及接觸區形狀進行了精確分析，而且分析了加載情況下螺旋錐齒輪齒面接觸中心點軌跡與無載下螺旋錐齒輪接觸軌跡的變化。
  6. The changing carbon potential carburization - hot oil matrempering technology of helical bevel gear for automobile driven axle is introduced in this article. the board test and production application show that the technology not only quenchs directly gear after carbrization, but also decreases the heat treatment deformation and raises the contact fatigue life of gear

    介紹了汽車驅動橋螺旋錐齒輪的變碳勢滲碳一熱油分級淬火工藝，臺架試驗及生產應用表明，該工藝與專用滲碳淬火掛具相結合，不僅可實現齒輪滲碳后直接淬火，而且熱處理變形小，齒輪接觸疲勞壽命也有所提高。
  7. Special grids is adopted for solid model of conical roller bearings by applying for three - dimensional solid and contact elements, aiming at its characteristic, stress and load distribution of elastic contact problems. finite element model built in the paper is fit for objective practice, with flexible - flexible contact bodies and surfaces - surfaces contact mode

    本文針對汽車后橋傳動錐軸承的接觸彈性變形特點、接觸應力及負荷分佈規律，採用三維實體單元及三維接觸單元對圓錐滾子軸承實體模型進行特殊的有限元網格劃分，將接觸單元按柔體一柔體處理，採用面一面接觸分析模式，建立了符合實際的有限元模型。
  8. According to synthetical analysis on the feature of parameters, contact pressure & formation and load distribution of conical roller bearings, the limitation is discovered, based on classical solution

    通過對錐軸承的特徵參數、接觸應力和變形及負荷分佈特性的綜合分析，得出了圓錐滾子軸承的經典解析解存在局限性的結論。
  9. In term of that, the solution result in two different condition is achieved by ansys software. deep research and comparing analysis between the classical solution and the finite element result is made on contact stress & formation and load distribution of conical roller bearings by revised classical formula of elastic contact problems, according to finite element solution in two different interfering conditions

    根據有限元數值模擬結果對經典解析解中接觸彈性變形量與作用負荷的關系進行了修正，利用修正過的接觸彈性變形公式對汽車后橋傳動錐軸承的接觸應力和變形及負荷分佈規律在無游隙及負游隙兩種情況下進行研究，並將結果與經典解析解進行了對比分析。
  10. 4 ) combining the local synthesis method for the machine - tool setting parameters, tca and ltca, and the numerical simulation of stress procedure constructs the optimal design circle with feedback. the developed software system provides an efficient design tool for the spiral bevel gears with excellent transmission behavior, high strength and lower noise

    4 ）結合加工參數設計的局部綜合法、幾何接觸分析（ tca ） 、承載接觸分析（ ltca ）及應力過程數值模擬，構成了具有反饋的閉環優化設計迴路，並形成了相應的軟體系統，為設計嚙合性能良好、高強度、低噪聲的弧齒錐齒輪傳動提供了有效的工具。
分享友人
分享到 Line

分享到臉書