錐形流法 的英文怎麼說
中文拼音 [zhuīxíngliúfǎ]
錐形流法
英文
conical flow method-
Calculation of the jet parameters of a cavity charge by the conical infinitesimal analysis method
錐形微元劃分方法的聚能裝藥射流參數計算Abstract : approximate methods for calculating aerodynamic heating rates on space shuttles are discussed. various methods are given for predicting the heating rate at axisymmetric stagnation points, general three dimensional stagnationpoints and the leading edge stagnation point of wings. numerous laminar and turbulent heating techniques for flat plates and cones are analyzed and compared. a brief review of some methods is presented to predict heating rate for winward centerline and lateral direction off the symmetry plane. the results show that the methods are simpler and can guarantee enought precision for predicting aerodynamic heating environment of space shuttles
文摘:介紹了國內外預測航天飛機氣動加熱的工程計算方法.給出了軸對稱、非軸對稱和機翼前緣等各種外形駐點熱流密度的計算，分析和比較了平板、錐體的層流和湍流熱流密度計算的各種方法，概述了航天飛機迎風面中心線和離開中心線橫向熱流密度的計算.計算結果表明，本文方法用在航天飛機氣動熱環境初步設計中比較簡單並且有足夠精度In this thesis, a 2 - d axial symmetric n - s equation was solved by using steger - warming flux splitting, muscl, b - l model and finite volume method to simulate an experiment, which was to observe explosion phenomenon
本文用steger - warming分裂和b - l湍流模型的有限體積演算法求解二維軸對稱navier - stokes方程，數值模擬了錐形激波管中爆炸波運動和爆炸波正壓和負壓脈沖。Reference to the designation of die casting mould, we put forward some kinds of projects respect to the design and manufacture of dies of the special purpose machine. and we simulate die casting filling process 、 surface defect distribution and temperature field etc. of az91d magnesium alloy shell part with flow3d software
設計時將參照壓鑄模的設計方法，提出多種方案，並使用flow3d模擬設計軟體來模擬金屬液的填充過程，預測可能產生缺陷的位置，從而決定澆注系統的形狀和分佈，冷卻水道的流向和位置，分流錐的大小和位置。So by this method, we can test the water content of the raw cement slurry through testing the velocity of the detector, it is certainly that it can test other slurry, such as paper slurry, mud slurry, mine slurry ctc. the fluid mechanics charactoristic of the slurry is complex, therefore it is difficult to establish the two - dimension or three - dimension mathematical modle to decide the relationship between the water content and the revolving speed of the detector. so the research for rotational detector in this topic is through the method of proper regressive analysis of experimental datas to establish the relation among the water content, the palse and the voltage
料漿的流體力學性能是復雜的，要想通過建立二維或三維的仿錐形旋轉式檢測頭在料漿中旋轉的流體力學數學模型，來確定料漿水分含量與檢測頭的轉速關系是十分困難的，甚至是不可能的，因此本課題對于旋轉式檢測頭的研究，是通過對實驗數據進行多元線性回歸的處理方法，建立起水分含量與紅外線對管輸出的脈沖數p及電源電壓之間的關系。分享友人