錐形進位 的英文怎麼說
中文拼音 [zhuīxíngjìnwèi]
錐形進位
英文
pyramid carry-
The ultrastructure of the merozoites of eimeria tenellawas observed and discribed. the pellicle consist of two layer membranes, the outer membrane was a continous covering enclosing the whole merozoites, while the inner pellicular complex is interrupted at the anterior and the micropore, and thicken to form the polar ring and micropore. there are 24 microtubules under the pellicle of the merozoite which originated from the polar ring, all of them are connected with the polar ring, and extend alongside the inner pellicular complex to the middle of the merozoite. the head of the merozoite consists of a conoid, an apical vesicule and polar ring. the conoid is a hollow truncated cone. the conoid and spical vesicule can stretch and contract. there are three or more rhoptry and a lot of micronemes. the nucleus has nucleolus. and two layer membranes
利用透射電鏡對柔嫩艾美耳球蟲裂殖子的超微結構進行了觀察描述.柔嫩艾美耳球蟲裂殖子的表膜由外膜和內膜復合體兩層組成，外膜連續，內膜復合體在頭部斷開形成極環，在其它部位斷開形成微孔；裂殖子的膜下微管24根，起始於極環，向後延伸至細胞核處；裂殖子的頭部由頂泡、錐體和極環組成，錐體和頂泡可以伸縮；柔嫩艾美耳球蟲裂殖子棒狀體3個以上，微線數量很多，二者都由電子緻密的結構組成；細胞核位於裂殖子的中後部，外被雙層膜，有電子緻密的核仁和染色質Analyse the tooth geometry of klingelnberg cyclo - palloid spiral bevel gear., according to the relative position and kinematic relation of the cutter heads, virtual crown gear and the processed wheel blank, established the system of coordinates of the gear cutting, dedcuced the tooth face equation of the virtual crown gear, according to relations of the gear cutting and space theory of engagement, deduced the tooth face equation of klingelnberg cyclo - palloid spiral bevel gear, and drawing the three - dimensional graphs of the virutal crown gear and klingelnberg cyclo - palloid spiral bevel gear according to the design and setting parameters
對克林貝格擺線齒錐齒輪進行齒面幾何分析。根據銑齒加工中刀盤、搖臺和輪坯的相對位置和相對運動關系建立了切齒嚙合坐標系，由矢量的旋轉推導了產形輪齒面方程;根據空間嚙合原理和切齒嚙合關系推導了被加工齒輪的齒面方程;由設計參數和銑齒調整參數計算得到齒面離散數據，繪制了產形輪和擺線齒錐齒輪的三維齒形。Finally, by means of comparing the theoretical tooth surface equation with the tooth surface equation included errors of cutter position and cutter position angle, the quantitative analysis of the theoretical tooth shape and the tooth shape considering the errors of cutter position and cutter position angle was curried out based on the software above. from which, the effect of errors of cutter position as well as cutter position angle on the processed tooth shape and transmitting behavior of this kind of gearing was studied
最後，通過比較雙圓弧弧齒錐齒輪齒面理論方程與加入刀位及刀位角誤差后的齒面方程，應用上述軟體和通過進一步的數值計算，進行了無誤差的理論齒形與加入刀位及刀位角誤差后所得到的實際齒形之間的定量分析，比較直觀、方便、準確地對刀位及刀位角誤差對雙圓弧弧齒錐齒輪的齒形以及傳動的影響進行了初步研究。In the solid model building program, based on the cutting tooth theory of double circular arc profile spiral bevel gear and autocad software, a series of computer simulations about solid model building and cutting tooth process of the gear were curried out. the cutter ' s tooth shape, the processed gear blank shape and its conjugated tooth profile shape as well as visual movement relationship between generating gear and processed gear blank etc. were obtained. the relative position of cutter and processed gear as well as the movement trace and rule in the cutting process can be showed dynamically on screen
在實體建模程序中，以雙圓弧弧齒錐齒輪的加工原理為基礎，藉助繪圖軟體autocad ，模擬了雙圓弧弧齒錐齒輪銑刀盤刀齒形狀、輪齒毛坯形狀等，進而根據產形輪與被加工齒坯之間的共軛嚙合關系，進行了雙圓弧弧齒錐齒輪的實體建模及加工過程模擬，在屏幕上動態顯示刀具及被加工齒輪的相對位置及其加工時的運動軌跡和規律。分享友人