錐形量規 的英文怎麼說
中文拼音 [zhuīxíngliángguī]
錐形量規
英文
cone gauge-
In view of bearing capacity of the elastoplastic theory analysis, the author made a comparison between the achieved bearing capacity limit load pi / 4 of round base ( space problem ) and the limit load pi / 4 of bar groundwork foundation design ( plane problem ) from soil mechanics at home and abroad as well as foundation criterion, and explained why the value of formula in present design criterion from soil mechanics is inclined to be conservative. in the light of the author ' s many years experience of vibration test on the spot and the research work of relevant projects, the author worked over the dynamic pile testing of the bearing capacity of foundation and batholith, and gathered the parameter of dynamic analysis and testing. the author also talked over the difficult point of pile foundation design criteria in present batholith engineering world, i. e. the confirmation of batholith bearing capacity of pile end, from the following aspects : a ) confirmation of single axis counter - pressure strength of rock in house ; b ) f. e. m calculation of elastoplastic model ; c ) calculation of soil mechanics ; d ) deep well load test
然後，對巖土工程領域至今尚未解決，甚至不為人注意的考慮地基變形的地基承載力問題進行了實用化的探討，提出了考慮地基變形的地基承載力上程計算方法；對基於彈塑性理論分析的地基承載力國內尚未見報道的空間問題得到了圓形基礎（空間問題）的承載力界限荷載p _ （ 1 / 4 ） ，並與國內外土力學專著及地基基礎設計規范中的條形基礎（平面問題）的界限荷載p _ （ 1 / 4 ） ，進行了對比，從而定量上解釋了目前設計規范引用土力學承載力公式值偏於保守的這一情況；根據本文作者多年從事現場地基工程振動試驗及相關課題的研究工作，本文以截頭錐模型模擬地基，對地基（巖基）承載力的動測法進行了研究，為各類地基（包括巖基） ，匯總了動力分析和檢測川的參數：針對日前巖土工程界應用樁基設計規范中的難點? ?樁端巖基承載力的確定問題，從巖石室內單軸抗壓強度確定、基於彈塑性模型的有限單元法計算、土力學計算及深斤載荷試驗四方面進行了深入討論；本文作者根據多年現場載荷試驗的工程實踐，對深井荷試驗裝置的核心部分? ?反力裝置，設計了側壁支撐反力加載系統，該加載系統具有實用、簡便、穩定及安個等優點。Metric external taper screw thread and mating internal parallel screw threads - part 2 : gauging system, use of gauges, calculation of gauge dimensions and general features
米制錐形外螺紋和配對圓柱形內螺紋.第2部分:量規系統Inspection method for taper screw gauges
錐形螺紋量規的檢驗方法Morse taper gauges
莫氏錐形量規In term of that, the solution result in two different condition is achieved by ansys software. deep research and comparing analysis between the classical solution and the finite element result is made on contact stress & formation and load distribution of conical roller bearings by revised classical formula of elastic contact problems, according to finite element solution in two different interfering conditions
根據有限元數值模擬結果對經典解析解中接觸彈性變形量與作用負荷的關系進行了修正，利用修正過的接觸彈性變形公式對汽車后橋傳動錐軸承的接觸應力和變形及負荷分佈規律在無游隙及負游隙兩種情況下進行研究，並將結果與經典解析解進行了對比分析。Gauges for taper pipe threads
錐形管螺紋量規Round general use light gauge metal containers - nominal diameters for cylindrical and tapered cans up to 10 000 ml capacity
通用圓形小量規金屬容器.最大容量為10 000 ml的圓柱形罐和圓錐形罐的標稱直徑分享友人