錐柱狀 的英文怎麼說
中文拼音 [zhuīzhùzhuàng]
錐柱狀
英文
conico cylindrical-
Fig. 1 - 1 a, straight ( rectangular ) tourniquets fit optimally on cylindrical limbs. b, curved tourniquets best fit conical limbs. ( from pedowitz ra, gershuni dh, botte mj, et al : clin orthop 287 : 237, 1993
圖1 1a直(長方形)止血帶最適合用於柱狀的肢體。 b弧形止血帶適用於圓錐形的肢體。The result of fluorescence show that the fluorescence intensity of the surface of the treated glass slide connect with the probe immobile ratio of oligonucleotide. the more oligonucleotide probes have been linked with active group, the stronger fluorescence intensity is. for the strongest fluorescence, the technical conditions is : treatment of 2 % aminosilane of 20 minutes, treatment of 5 % aldehyde of 24 minutes, uv crosslinking of 150mj and washing of 5 minutes at 20
兩種檢測方法表明,當活性基團呈柱狀、分佈均勻且尺寸比較大( 200nm )時,有利於寡核苷酸探針的連接,且連接探針數量多,玻片表面熒光強度強,固定率高;當活性基團呈錐狀、分佈及尺寸不均勻( 150nm ( 300nm )時,連接的寡核苷酸探針數量少,玻片表面熒光強度弱,固定率低。The uv - vis transmission spectra and concentrations of metal ion impurities in different part of dkdp crystal was measured. the results show concentrations of metal ion impurities on the ( 100 ) face is higher than that on the ( 110 ) face and absorption on the ( 100 ) face is bigger than that on the ( 110 ) face
通過測試點狀籽晶生長dkdp晶體不同部分雜質金屬離子的含量和紫外可見透過光譜,結果發現dkdp晶體柱面的雜質金屬離子含量比錐面高,柱面的紫外可見吸收比錐面大。The opening stress and the life of crack growth is calculated and compared with the test results and the experience formula. the feasibility of the newman theory of opening stress used in the high strength steel is validated. then through the slice synthesis method, the three dimension surface crack of the weld joint of cone - cylinder is decomposed into many plane through cracks
本文將基於裂紋閉合現象建立的帶狀屈服模型,用在平面貫穿裂紋中,計算此時的裂紋張開應力和疲勞裂紋擴展壽命,與試驗結果和經驗公式比較,驗證newman裂紋張開應力理論在高強鋼中的可行性;然後,用切片合成法,把潛艇結構凸錐柱結合殼焊縫處的三維表面裂紋分解成平面貫穿裂紋,用帶狀屈服模型的理論來分析平面貫穿裂紋,得到裂紋沿深度方向的擴展速率,進而得到潛艇結構的疲勞壽命。General rules were validated and a new rule was discovered : i. e. the shape 0f these two stress fields are same, the equivalent stress of the round corner in the bottom reached its maximum at the first phase, the equivalent stress of the edge of hole reached its maximum at the third phase, the equivalent stress of flanging with cone - shaped punch descend more than that with column - shaped punch at the fourth phase i. e. the phase of deformation completed
驗證了一般規律,也發現了新規律,即兩者的應力場形狀相同,底部圓角處等效應力在變形第1階段最大,孔口邊緣處等效應力最大出現在變形第3階段,第4階段(變形終了時)錐形沖頭翻邊的等效應力比柱形沖頭翻邊時下降更大。One fascinating property of steel mirrors is their mouldability - they can be bent into the shape of a circular cylinder or even a cone
鏡鋼的特色是可以屈曲成圓柱甚至圓錐狀。圓柱及圖錐鏡面所反射出來的圖像往往變得十分有趣甚至難以辨認。But the sbg has the complicated tooth surface structure, which makes its manufacturing and measurement more complicated than those of ordinary cylindrical gear. meanwhile, it is an exploring phase to analyze and diagnose sbg ’ s process errors
然而,由於螺旋錐齒輪的齒面形狀復雜,與普通圓柱齒輪相比,其加工和測量非常復雜,對其工藝誤差分析與診斷也處于探索階段。Object shapes are represented by primitive shapes ( box, cone, cylinder, sphere ), and complexes of polytopes ( line segments, convex polygons, convex polyhedra )
對象形狀用基本形狀(方框,圓錐形,圓柱,球)和復雜的多面體(線段,凸多邊形,凸多面體)來表達。The research results reveal that the gravitational field can not be neglected in keeping non - equilibrium state of this system, which ensures the stabilization of the tapered bed and prevents from bed clogging
分析結果表明:重力場的存在,維持了體系的非平衡狀態、保證了錐形床的穩定操作,避免了柱子堵塞及壓密化。分享友人