鍵槽尺 的英文怎麼說

中文拼音 [jiàncáochǐ]
鍵槽尺 英文
key seat rule
  • 鍵 : 名詞1 [機械工程] （使軸與齒輪、皮帶輪等連接並固定在一起的零件） key 2 [書面語] （插門的金屬棍子）...
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  • 尺 : 尺名詞[音樂] （中國民族音樂音階上的一級 樂譜上用做記音符號 參看「工尺」） a note of the scale in ...
  1. Keyway broach with chamfer types and dimensions

    帶倒角齒鍵槽拉刀型式與尺寸
  2. Stressed - type fastenings with taper action ; taper keys with gip head, keyways, dimensions and application

    錐度驅動應力型緊固件.彎頭斜鍵鍵槽尺寸和應用
  3. Widened flat body keyway broach types and dimensions

    加寬平刀鍵槽拉刀型式與尺寸
  4. Flat body keyway broach types and dimensions

    平刀體鍵槽拉刀型式與尺寸
  5. Washer for keyway broaching. dimensions

    鍵槽拉削用墊片.尺寸
  6. Holder for keyway broach. dimensions

    鍵槽拉刀夾頭.尺寸
  7. Was the keyway created using a min arc condition dimension of. 0. 63

    鍵槽的生成是用了0 . 63最小圓狐的尺寸條件。
  8. Rod - ends with self - aligning ball bearings. long threaded shank and keyway. dimensions and loads

    帶自位球軸承的桿端.長螺紋桿和鍵槽.尺寸和負荷
  9. Shell end mills with tenon and parallel key drive ; dimensions

    帶榫和平行鍵槽的筒形端銑刀.尺寸
  10. Semi - circular woodruff keys - dimensions of cross sections and keyways

    鍵和鍵槽的剖面尺寸
  11. Woodruff keyseat cutters. dimensions

    半圓鍵槽銑刀.尺寸
  12. Mechanical transmissions. tangential keys and keyways. dimensions and tolerances

    機械傳動.切向鍵和鍵槽.尺寸和公差
  13. Rod - ends with self - lubricating spherical bearing. long threaded shank and keyway. dimensions and loads

    帶自潤滑裝置的球形接頭.有鍵槽長螺紋桿.尺寸和載荷
  14. Rod - ends with self - lubricating spherical bearing. long threaded shank without keyway. dimensions and loads

    帶自潤滑裝置的球形接頭.無鍵槽長螺紋桿.尺寸和載荷
  15. Square and rectangular keys and keyways - width tolerances and deviations greater than basic size

    方形和矩形鍵和鍵槽.寬度公差和大於基本尺寸的偏差
  16. Taper keys - cross section dimensions of keys and keyways

    鍵和鍵槽的剖面尺寸
  17. Parallel keys - dimensions of cross sections and keyways

    鍵和鍵槽的剖面尺寸
  18. Rod - ends with self - aligning ball bearings. long threaded shank without keyway. dimensions and loads

    帶自位球軸承的桿端.無鍵槽的長螺紋桿.尺寸和負荷
  19. If the confirmed size from the above formula is not practical, it is necessary to apply flange wheel hub and checking board, the checking board should be connected with gear with bolt, and the bolt should be on special pitch circle radius

    21 . 1如果從上面公式確定的鍵槽尺寸不實用，那麼應採用帶鍵的法蘭式輪轂和檢查板，檢查板用螺栓連接在輪上，螺栓處于特別的節圓半徑上。
  20. Stressed - type fastenings with taper action ; taper keys, keyways, dimensions and application

    錐度驅動應力型緊固件.斜鍵鍵槽尺寸和應用
分享友人
分享到 Line

分享到臉書