鎖緊栓 的英文怎麼說
中文拼音 [suǒjǐnshuān]
鎖緊栓
英文
lock plunger-
Simple : compared to flange, its more light, the locking machine is designed handiness, the bolt quantity are few, doesn ' t need to holeblockage
簡易它比法蘭輕、鎖緊機械設計巧妙，螺栓數量少，無須對孔對鎖。The russians who cleaned the embassy simply unscrewed the bolts(which were well oiled)on the security door lock and walked straight in.
負責打掃使館的俄國人只需打開安全門上的緊鎖螺栓（上過不少油），即可徑直進入機房。Anchor bolts. part 2 : tests for determining the characteristics properties and c ritical and minimum distances
鎖緊螺栓.第2部分:特性和臨界及最小距離的測定試驗It can be installed in horizontal or vertical. sealing gasket must be put on the connected, then equably tight the bolt
本閥可水平安裝或垂直安裝，安裝時兩法蘭連接中間必須加密封墊片，然後鎖緊螺栓。For example : inflates the screw, key, double head the spiral, inside and outside hexagon bolt, the horse - drawn vehicle screw, the hexagonal nut, locks the nut, flange surface nut, thin nut and so on
如：膨脹螺絲、平鍵、雙頭螺、內外六角螺栓、馬車螺絲、檔圈，銷，鍵，非標準件，六角螺栓， ，等六角螺母、鎖緊螺母、法蘭面螺母、薄型螺母等等。Loosely install all the head bolts and the special washers ， then thread them in until they are finger - tight
鬆鬆地裝上所有的汽缸蓋螺栓和特殊?圈，然後用手鎖緊它們。Bolt, hexagonal head, with locking hole, short thread
帶鎖緊孔六角頭短螺紋螺栓Fasteners - lockbolts, protruding head, with close tolerance and titanium alloy t - a6v shank and with collar in steel xc 10
緊固件.緊公差t - a v鈦合金桿和xc鋼環凸頭鎖緊螺栓Fasteners - lockbolts, 100 o countersunk head, with close tolerance and titanium alloy t - a6v shank and with collar in steel xc 10
緊固件.緊公差t - a v鈦合金桿和xc鋼環沉頭鎖緊螺栓Anchor bolts. fitness for use tests
鎖緊螺栓.使用試驗的適合性Anchor bolts. part 1 : general, terminology, design safety rules for anchor bolts joints
鎖緊螺栓.第1部分:鎖緊螺栓接頭的概述術語和設計安全性規則Fasteners - lockbolts, protruding head, with close tolerance and titanium alloy t - a6v shank and with collar in aluminium alloy 2024
緊固件.緊公差t - a6v鈦合金桿和2024鋁合金環的凸頭鎖緊螺栓Fasteners - lockbolts, 100 o countersunk head, with close tolerance and titanium alloy t - a6v shank and with collar in aluminium alloy 2024
緊固件.緊公差t - a6v鈦合金桿和2024鋁合金環的100沉頭鎖緊螺栓The valve can be installed in horizontal or vertical. add seal cushion between two flanges connection and screw down bolt
本閥可水平或垂直安裝，安裝時兩法蘭聯接中間必須加密封墊片，然後均勻鎖緊螺栓。Pay attention to the flow direction of medium marked on the body. add the sealed shim between the two flanges and then screw down the bolt
安裝時請注意閘門本體上標明介質流向。兩法蘭連接時必需加密封墊片，然後均勻鎖緊螺栓。Aircraft bolts and nuts - nuts, hexagonal, slotted castellated, reduced height, iso m or iso mj threads, 4h5h or 5h tolerance class according to diameter
飛機用螺栓和螺母. iso m或iso mj螺紋直徑公差等級h h或h .帶槽帶缺口減少高度帶鎖緊孔左旋普通六角螺母Installation of flange connecting valve is on diagram. lock down the connecting bolt after add sealing washer
安裝如示意圖，加密封墊后均勻鎖緊聯接螺栓。Pay attention to the flow direction of medium showed on the body. installatio of flange connecting valve is on diagram. lock down the connecting bolt after add sealing washer
安裝時請注意閥體上標注（箭頭）的介質流向，安裝如示意圖，加密封墊后均勻鎖緊聯接螺栓。Pay attention to the flow direction of medium showed on the body. installation of flange connecting valve is on diagram. lock down the connecting bolt after add sealing washer
安裝時請注意閥體上標注（箭頭）的介質流向，安裝如示意圖，加密封墊后均勻鎖緊聯接螺栓。Aircraft bolts and nuts - nuts, hexagonal, plain, reduced height, reduced across flats, with locking holes, iso m or iso mj threads, 4h5h or 5h tolerance class according to diameter
飛機用螺栓和螺母. iso m或iso mj螺紋直徑公差等級4h5h或5h減少高度減少高度帶鎖緊孔左旋普通六角螺母分享友人