鎢弧焊 的英文怎麼說
中文拼音 [wūhúhàn]
鎢弧焊
英文
tungsten-arc welding-
Before repairing, basing on the actual working condition, concerning the weldability, stress and deformation issues, the scheme of the cold welding technology whose essential being gtaw, low temperature preheating, postweld hammer the welded seam was established
修理前，圍繞兼顧解決焊接性、應力和變形問題，結合實際施工條件制定了以手工鎢極氬弧焊、鎳基焊絲、焊前低溫預熱、焊后錘擊焊縫為要素的冷堆焊工藝。Automatic tig welding technology on manufacture of the micro motor shell
電機機殼薄壁鋼筒自動鎢極氬弧焊技術Simulation on tig welding of aluminum alloy plate and residual stress predicting
鋁合金平板鎢極氬弧焊數值模擬與殘余應力預測Abstract : with the aids of computer ' s hardware, executive mechanism of weld arc length automatic controller of all - position pipe welder and additional software, an automatic system for arc striking has been developed, in which touch - starting method using tiny current is introduced. utilizing this method, the ablation ratio of tungsten electrode and tungsten inclusion ratio of welded seam is far smaller than normal touch - starting method. and the successful ratio of arc striking is high
文摘:用全位置自動焊管機弧長自動控制系統的計算機硬體和執行機構，僅增加部分程序，設計了採用小電流接觸引弧法的自動引弧系統，鎢極燒損和焊縫夾鎢遠小於普通的接觸引弧方式，引弧成功率很高。Tungsten and tungsten alloy electrodes for arc welding and cutting
電弧焊接和切割用鎢及鎢合金焊條Cerium tungsten electrodes have easy arc starting performance and low are keeping current. it is especially used to weld pipes, stainless steel articles and fine miniparts
鈰鎢電極在低電流條件下有著優良的起弧性能，維弧電流較小，因此，它常常用於管道、不銹鋼製品和細小精緻部件的焊接。Tungsten electrodes for inert gas shielded arc welding, and for plasma cutting and welding
等離子切割和焊接用惰性氣體保護弧焊用鎢焊條Arc welding and cutting - nonconsumable tungsten electrodes - classification
電弧焊和切割.非自耗鎢電極.分類Arc welding and cutting - nonconsumable tungsten electrodes - classification iso 6848 : 2004 ; german version en iso 6848 : 2004
電弧焊接和切割.非自耗鎢電極.分類Wps standard welding procedure specification - gas tungsten arc welding of aluminum m - 22 or p - 22, 10 through 18 gage, in the as - welded condition, with or without backing
在焊接條件下有或沒有墊板10到18規格m - 22 p - 22鋁的氣體保護鎢極弧焊的標準焊接程序規范Firstly, backing with double - sided in - phase welding, welding method is gtaw. secondly, after filling outside one layer, welding with saw. finally, weld the inside with saw
先用雙面同步焊打底，焊接方法為鎢極氬弧焊；然後外側用焊條電弧焊填充一遍后再用埋弧焊焊接；最後用埋弧焊焊接里側。One - side welding and double - forming welding procedure of ta2 argon tungsten - arc welding
2的鎢極氬弧焊單面焊雙面成形焊接工藝研究The arc physical characteristic of mixed gases ( ar + he + co2 ) and its effects on weld shaping were discussed
摘要採用鎢極氬弧焊對不同比例氬氦二氧化碳混合氣體的電弧物理特性及其焊縫成形進行了實驗。Tig tungsten - arc inert - gas welding
鎢極電弧惰性氣體保護焊Tig welding rods and solid wires for mild steel and low alloy steel
低碳鋼及低合金鋼用惰性氣體保護鎢極電弧焊條及焊絲Specification for approval testing of welders when welding procedure approval is not required - tig or mig welding of aluminium and its alloys
不要求批準焊接工藝時焊工的鑒定考試規范.第2部分:鋁及鋁合金鎢極惰性氣體保護電弧焊或熔化極惰性氣體保護電弧焊Specification for stainless steel electrodes for flux cored arc welding and stainless steel flux cored rods for gas tungsten arc welding
助溶劑芯弧焊用不銹鋼焊條和鎢電極惰性氣體保護焊用不銹鋼助溶劑芯焊條規范Wps m - 1 p - 1 s - 1, 1 2 standard welding procedure specification for gas tungsten arc welding followed by shielded metal arc welding of carbon steel m - 1 p - 1 s - 1, group 1 or 2, 1 8 through 1 - 1 2 inch thick, er70s - 2 and e7018, as - welded or pwht condition
在焊接或pwht條件下1 8到1 - 1 2英尺厚er70s - 2和e7018碳鋼的保護金屬電弧焊和鎢電極惰性氣體保護電弧焊的標準焊接程序規范分享友人