鑲塊模 的英文怎麼說

中文拼音 [xiāngkuāimó]
鑲塊模 英文
assembled die
  • 鑲 : 動詞1. （嵌入） inlay; set; inset; insert; mount 2. （圍在邊緣） rim; edge; border; lace
  • 塊 : 名詞（古時佩帶的玉器） penannular jade ring （worn as an ornament in ancient china）
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  1. The design and machining technology process of its molding part including the front moulding plate 、 front mould kernel 、 back mould plate 、 back mould kernel 、 back mould set piece 、 incline guide pin 、 slide steatite etc, and the choice and calculation of technology parameters of the impotent part, the design process of extrusion outfit, inject system and other makeup are specified in detail ; test and product have been introduced

    詳細地敘述了模具成型零件包括前模板、前模仁、后模板、后模仁、后模鑲件、斜導柱、滑塊等的設計與加工工藝過程，重要零件的工藝參數的選擇與計算，推出機構與澆注系統以及其它結構的設計過程，並對試模與產品缺陷作了介紹。
  2. Die - casting die components - part 2 : round insert block

    壓鑄模零件第2部分:圓形鑲塊
  3. The split solar water heating system designed anddeveloped by diangong solar is the most advanced solar water heater system. it realizes the organic separation between the heat collector and the water tank. it advanced and scientific structure makes it in accordance with the general design of the residential building. the solar heat collector has become an organic modularized construction component enbedded in the roof, balcony or walls. in such a way. it realizes a perfect combination with the construction and is accepted as the first choice in green ecological energy - saving residential constructions

    電工太陽能開發設計的分體式太陽能熱水系統是目前最先進的太陽能熱水器系統，實現太陽能集熱器和儲水箱有機分離，結構科學先進，從而使太陽能集熱器完全可以與建築住宅總體設計緊密結合，太陽能集熱器成為模塊化建築構件，鑲嵌安裝于建築屋面、陽臺、墻壁等，使其成為建築的有機組成部分，達到與建築完美結合的目標，是綠色生態節能住宅的首選。
  4. Die - casting die components - part 3 : rectangular insert block

    壓鑄模零件第3部分:矩形鑲塊
  5. Finally, every module was embedded into the web pages of the sdts system by using the html language

    最後結合html語言把各個模塊鑲嵌到培訓系統的主頁當中。
  6. In this paper, systemic experiments are performed on the compositions, processes, microstructures and properties of some high quality pm inserts. main procedures such as mixing, compaction, sintering, re - compaction, re - sintering, heat - treatment, properties detection and mould design and so on are included in these experiments

    本文對幾種高性能粉末冶金搖臂鑲塊的成分、工藝、組織和性能等進行了系統的實驗研究，包括混粉、初壓、初燒、復壓、復燒、后續熱處理、性能檢測、現場模具設計等。
分享友人
分享到 Line

分享到臉書