長程有序度 的英文怎麼說
中文拼音 [zhǎngchéngyǒuxùdù]
長程有序度
英文
degree of longrange order-
A 2 - d fem program is designed to simulate and compute thermal - creep - stress field in a long beam on batholith and taipu river pumping station. some conclusion available in designing and construction are presented
編制了平面有限元程序，模擬計算了巖基上長梁和太浦河泵站工程的溫度徐變應力場，得出一些對工程設計和施工有益的結論。Then, the program is used to simulate the flow across the backward - step, and the conclusion is testified that the circumfluence length is related to the reyonlds number
同時，利用程序對后臺階繞流流動進行計算，驗證了后臺階繞流迴流長度和雷諾數有關的結論。It is the key of ebfs, therefore, furthermore calculation about link are carried out in this thesis, introduced achieved research, summarized the affect of link on whole capability in the first, the second, numerical calculation are proceeded on link with ansys : with the purpose of discussing yielding mode critical length of link, established five different specimens ; with the purpose of discussing the influence of h / tw of web, b / tf of flange and h / b, established eighteen different specimens ; with the purpose of discussing the affect of stiffener, established four different specimens, and elaborated the affect of stiffener on link based on achieved test researches
因此，本文對耗能梁段進行進一步計算分析，概述耗能梁段對整體性能的影響，並利用有限元程序ansys對耗能梁段進行數值計算：針對耗能梁段的屈服類型建立5種不同長度的模型，計算討論耗能梁段屈服類型的長度劃分；針對耗能梁段腹板高厚比、翼緣寬厚比以及梁段截面形狀等因素共建立了18種模型進行計算分析；針對加勁肋對耗能梁段的作用建立了4種模型，並結合已有的試驗闡述了加勁肋對耗能梁段的影響。Second, the starting and stopping behaviors under disturbed condition are analyzed and calculated by using the dynamic concentrative parameter model, which gives some advice to better prescribe refrigeration system and set theoretic foundation for carrying out automatic control of refrigeration system. third, the normal running process is analyzed and calculated by means of rational matching theory, which gives some advice on how to better understand the parameter change under steady state and the affection of inlet - parameter on evaporator. fourth, the simulation software with dynamic characteristic is designed, which can be applied to calculate thernio - parameter of cryogen, air humidity and frost thickness under different initial and boundary conditions, and to carry out dynamic simulation under conditions of dryness, wetness and frostiness, at the same time, to achieve detection and simulation at any stage from starting to stopping
本文的主要內容如下： 1 ）對翅片管蒸發器結構特點進行分析，選取適當的微元控制體，就干、濕和霜工況下對每個微元分別進行傳熱傳質分析，基於經驗關系式確定霜的有關參數，對于霜工況下的霜生長建立模型，經適當假設，運用質量守恆、能量守恆和動量守恆方程建立適合動態模擬的蒸發器數學模型，為系統模擬奠定基礎； 2 ）對蒸發在大擾動下的開、停機過程，運用動態集中參數模型進行分析和計算，為更好地描述製冷系統運行的全過程奠定基礎，同時也為製冷系統實現自動控制提供一定的理論基礎； 3 ）對蒸發器正常運行過程，運用動態分佈參數和參數間定量耦合的觀點來分析和計算，為更好地了解穩態工況下各點參數的變化情況及各入口參數對蒸發器動態特性的影響即蒸發器性能對各參數變化的敏感性； 4 ）編寫翅片管蒸發器動態特性模擬計算程序，可以計算不同邊界條件和初始條件下的製冷劑熱力參數、空氣溫濕度和霜厚度分佈場，實現對翅片管蒸發器在干、濕和霜工況下的動態模擬。On the basis of the others, according to the constructional feature of the constitution of the composed soil nails, the computation mode of the he strut frame made of composed soil nails was set up to analyze the distortion of the he strut frame made of composed soil nails when it is stressed. with the engineering data, the strut frame made of composed soil nails is analyzed with the program ababqus, and the effects of the distortion characters, the property of the deposition of the ground, the mechanical property of the soil nails, the variation of the length and the separation of the soil nails, and the diametric of the mixing piles on the strut frame made of composed soil nails, and the distortion property of the strut frame made of composed soil nails under different ground conditions
在總結前人的研究成果下，針對復合土釘墻構造的特點，建立了模擬復合土釘墻受力變形的計算模型，並結合工程實測資料，運用大型通用有限元程序ababqus對復合土釘墻進行了有限元分析，詳細討論了復合土釘支護結構開挖過程中的變形特性、地面沉降性狀、土釘受力性狀；土釘長度變化、土釘間距變化、攪拌樁樁徑變化對復合土釘支護結構的影響；復合土釘支護結構在不同地基條件下的變形特性。Firstly, by numerical and theoretical analysis, the author compares some existent confidence intervals, for example, " exact " confidence interval, wald confidence interval and bayesian confidence interval, and finds some deficiencies points of the confidence intervals, whose modification version has been proposed. also, several better confidence intervals such as are also presented. secondly, for given confidence coefficient and interval width, the author constructs a class of asymptotical two - stage interval estimate procedures. at the same time, under varies restriction of confidence coefflcientent interval width, the optional sample size of the first stage has been computed by numerical computation. the numerical computation shows that the method considered in this dissertation have good properties and applied value
同時，由於poisson分佈的特性，我們知道不存在其參數區間長度小於0 . 5的置信區間，基於這些情況，我們主要展開了以下兩個方面的研究：一是利用數值計算分析與理論分析的方法對現有的若干置信區間如「精確」置信區間， wald置信區間， bayes置信區間等進行分析比較，發現了一些缺陷，針對這些缺陷，我們進行適當的修正，並得到幾種性質較好的置信區間如：修正大樣本區間jeffreys原則下置信區間二是針對已給定的置信系數與區間長度，我們提出了一種漸近的兩階段區間估計程序，並利用數值計算的方法，在各種置信系數與區間長度限定下，算出了最優的第一階段觀測次數（抽樣量） ，大量數據表明，本文考慮的方法性態良好，具有應用價值。First, it was taken that a discuss about the effects of geometry parameters of each piezocrystal on direction parameters ( main lobe width, side lobe amplitude, elimination of grating lobes ), amplitude of ultrasonic pressure, element viberation pattern, mutual radiation among elements, efficient test regions, ability to keep accurate and near - field distance and so on. based on the direction of ultrasonic field in ulpa deduced by ourselves. in addition, on the base of integrating all kinds of factors, it was put forward that the principle and method for optimized design of geometry parameters of piezocrystals in ulpa transducer, and its design programme and interface were compiled
首先在推導超聲相控線陣換能器聲場的指向性的基礎上，就各個晶片幾何參數對指向性指標（主瓣寬度、旁瓣幅度、消除柵瓣） 、聲壓幅值、陣元振動模式、陣元間互輻射、有效檢測區域、精確控制能力、近場長度等方面的影響進行了論述，並在綜合各方面影響的基礎上，提出了晶片幾何參數優化設計的原則和方法，編寫了設計程序和界面。A lot of experiments have been done in the process of exploiture soft packaging li - ion battery about how to choice the rational arts and crafts. the content include : how to deal with the collector, add how much pvdf in the material, how long the material need to stirring and the right viscidity, how much condubtivity agent the electrode need, what theckness is best, choice different collectors, the degree of dryness of the electrode, theckness of pressed model, how much electrolyte will be added, placement how long after added the electrolyte, system of formation how to influnce the battery, in formation the battery need or not need preesure from outside, how to vacuumize and the optimize matching positive pole and negative pole. with these practice make sure the parameter of the positive pole should less than 90 m ; according to different vacuumize order the conduc - tivity agent in anode will be 5mass % and 9mass %, respectively, and in cathode the data is 2mass % ; every 100mah added to 0. 4 ml electrolyte ; before formation the battery should be placement 8 hours and the system of formation must be less than 0. 01c before the voltage reach to 3. 0v ; should press in outside when battery in formation ; to these batteries which capacity more than 350mah the vacuum time not excess 15s ; the optimize matching positive pole and negative pole between 2. 10 : 1 and 2. 15 : 1. finally make out the battery which cycling performance and security are all very well
液態軟包裝鋰離子電池的研究主要是對關鍵工藝進行了優化設計，具體包括:集流體的處理、 pvdf的加入量、漿料攪拌時間和粘度、導電劑的加入量、電極膜的厚度、不同集流體的選擇、電極膜的乾燥程度、壓型的厚度、電解液的加入量、注入電解液后靜置時間的長短、化成制度的影響、化成時電池所具有的壓力影響、抽真空的處理、正負極活性物質的匹配。最後確定出液態軟包裝鋰離子電池最佳工藝參數:正極膜的厚度小於90 m ;根據化成時不同抽真空順序，確定正極膜中的導電劑的加入量分別為5mass %和9mass % ;負極膜中導電劑的加入量為2mass % ;電解液的加入量為每100mah添加0 . 4ml ;化成前電池的靜置時間應當大於8h ;電池在3 . 0v之前採用小於0 . 01c的化成制度;在化成過程中應當施加一定的外部壓力;對於350mah的電池抽真空的延時不應大於15s ;而正負極活性物質的質量比應當在2 . 1 : 1 2 . 15 : 1之間。According to the characteristic of cnc plasma cutting machine it could improve the process quality of cutting piece in effect for choosing proper technics, for example, cutting section point, aspect, sequence, speed etal during the period of processing, and elaborating towards the distortion control of single side piece, slightness piece, profiled piece and particularity piece at the same time
根據數控等離子切割機的特點，在加工過程中正確選擇切割的起點、切割方向、切割順序、切割速度等工藝，可以有效提高切割件的加工質量，同時對單邊工件、細長件、異型件以及特殊件的變形控制進行了詳細地闡述。The strength of convergent shock was enhanced in cylindrical and spherical geometries than in planar geometry. the bubble became more wide and big and the spike became more narrow and long. it showed in spherical implosion that the spike close to the symmetrical axis grew faster than the ring one away from the symmetrical axis
第四，利用lared一s程序模擬柱和球幾何內爆過程中rt不穩定性增長，表明收縮幾何效應對內爆過程中不穩定性的增長有重要影響，柱和球幾何中聚心沖擊波的強度大於平面情況，氣泡變得更加寬而大，而尖頂變得更加細而長。It is firstly found that for alloys in metastable region, with enhancement of atomic interaction energy, volume fraction and density of " phase particulate are increased, size and nucle ' ation rate of ordered phase raised, decline pace of composition in disordered matrix around the order phase is accelerated, composition order parameter and long range order parameter of ordered phase increased, i. e. process of clustering and ordering are accelerated
首次發現，隨著原子間相互作用勢的增加，亞穩區合金中有序相的體積分數和顆粒密度有所增加，有序相的尺寸和形核率有所提高，有序相周圍的無序基體濃度的降低有所加快，有序相內的成分序參數和長程序參數有所提高，即促進了原子簇聚過程和有序化程度。In this dissertation, correlative research of longer - term voltage stability have been carried out, including some slow dynamic elements, such as on - load tap changer ( oltc ), maximum excitation limiters ( mel ), etc. the effects of these slow dynamic elements on the course of voltage instability or collapse are revealed from the point of view of time - domain simulation
本文基於pss e程序中的擴展動態模擬模塊，對考慮有載調壓變壓器（ oltc ） 、最大勵磁限制器等慢動態元件的中長期電壓穩定進行了相關的研究，從時域模擬的角度揭示這些慢動態元件在電壓崩潰過程中所起的作用。A monte - carlo method has been developed for simulating the growth of epitaxy flims. the program was compiled using turbo basic language. the influence of growth rate and temperature on surface morphology was studied. the model we used was an advanced diffusion limited aggregation ( dla ) model. the process of deposition and diffusion were considered in this model
本文利用montecarlo方法，結合薄膜生長理論，採用turbobasic語言編寫程序，對外延薄膜的生長過程進行了模擬。所用的模型為改進的擴散有限聚集模型（ dla ） ，研究了薄膜生長過程中沉積速率和襯底溫度對表面形貌的影響。Also shown by afm images are the regular features of crystals and ordered crystal domains for the film grown on 200 substrates, the morphologies indicate a phase transition, which is clearly confirmed by contrast between ( 0, 0 ) and ( 0, 1 ) absorption features and the bathoshift of ( 0, 0 ) absorption peak corresponding to the temperature of the substrate
Afm圖像同時顯示，在200的襯底上生長的薄膜具有規則的晶體外型和有序排列的微疇，說明存在結晶轉變。 f - ptcdi薄膜的吸收光譜的（ 0 ， 0 ）和（ 0 ， 1 ）性狀的強度對比與紅移程度隨襯底溫度的變化清晰地表現出150到200之間存在一個相變， dsc測試說明該轉變是從低有序到高有序度的轉變。As the temperature of pyrolysis and the soak time increasing, the carbon materials become more stacked, the specific surface area reduces, both reversible capacity and irreversible capacity decrease, the initial coulumbic efficiency increases, and the hysteresis in the voltage profile between charge and discharge is cut down
隨著熱處理溫度的升高和恆溫時間的延長，所得炭材料的有序化程度增加，比表面積減小，可逆嵌鋰容量與不可逆容量均減小，首次充放電效率增大，電壓滯后現象得到抑制。The two - dimenstional xy model undergoes an unusual klosterlitz - thouless phase transiton at low temperature, where the system magnetization still vanishes but there is an quai - long order with the spin configuration like the vortex pair
二維xy模型在較低溫時發生了特殊的kt相變，系統磁化強度仍為零，但呈現出類似渦旋對的準長程有序。In view of that thought, thesis first gives the conceptions : microscopic state of economics, economic order, economic orderization and economic entropy, at the same time, defining the orderly degree, to describe the regional economic state and level during the course of regional economic growth and development. based on these conceptions, establishing economic entropy measure the orderly degree of regional economics using economic order as measuring index through economic order changing, the orderly degree of regional economics means harmonious and coordinative level reached by mutually contacting ? acting on and affecting thorough all essential factors and all subsystems contained in regional economic system to promote growth and development of regional economics, and micro - measuring means measuring the orderly degree of regional economics from individual welfare. the mathematic analyzing to the economic entropy indicates that the it reflects the long - term changing trend of the orderly degree of regional economics : it will increase during fluctuation
基於這一思想，論文首先提出經濟微觀態、經濟序和經濟有序化概念，以描述區域經濟在有序化過程中某時刻所處的狀態和水平;在此基礎上定義經濟熵，以經濟序作為測度指標，以經濟序的變化度量區域經濟有序程度，即區域經濟系統各要素和各子系統通過相互聯系、相互作用和相互影響從而提高區域經濟系統整體發展效率和速度的協調水平，而微觀度量則是指該度量是從個體福利水平的角度進行的;接著對經濟熵進行了數學分析，證明其反映了區域經濟有序程度的變化趨勢，即在波動中趨向增加，並用經濟增長理論驗證了該結論。List. however, several factors make them unsuitable for use in highly concurrent applications - their single collection - wide lock is an impediment to scalability and it often becomes necessary to lock a collection for a considerable time during iteration to prevent
然而，某些因素使得它們並不適用於具有高度並發性的應用程序中它們的集合范圍的單鎖特性對于可伸縮性來說是一個障礙，而且，很多時候還必須在一段較長的時間內鎖定一個集合，以防止出現When ba / sa = 3 / 1 - 9 / 1, longer domains ( ba ) are in majority, and some hydrophobic " holes " ( caused by the difference in height between ba and sa ) formed in the alkyl layer which can be used to fabricate special functional nanostructures
衍射強度出現「 w 」形狀變化，表明在中間比例所形成的長短鏈交錯的結構向兩邊變化時，都要經歷混合膜有序度降低的過程。這為制備復合膜時比例的選取，提供了有意義的數據。The order in one body can increase, provided that the amount of disorder in its surroundings increases by a greater amount. this is what happens in a living being
倘若周圍環境的無序度增長得更多的話，個體的有序程度是可以增加的，這就是在生物體中發生的事情。分享友人