閂體 的英文怎麼說

中文拼音 [shuān]
閂體 英文
breechblock
  • : Ⅰ名詞(門閂) bolt; latch Ⅱ動詞(用閂插上) fasten with a bolt or latch
  • : 體構詞成分。
  1. Two other effects are transient phenomenon called single event upset ( seu ) and single event latchup ( sel ). in this paper, some means to harden the devices against these phenomena are used. guard banding around nmos and pmos transistors greatly reduces the susceptibility of cmos circuits to lachup

    在本文設計中,採用雙環保護結構,大大的降低了cmos集成電路對單粒子鎖效應的敏感性;對nmos管採用環型柵結構代替傳統的雙邊器件結構,消除了輻射感生邊緣寄生晶管漏電效應;採用附加晶管的冗餘鎖存結構,減輕了單粒子翻轉效應的影響。
  2. 5 ) the 3 - d geometry and finite element model of the assembly of the optimized obturator of the breech mechanism is set up in terms of the optimized structural parameters. quasi - static and dynamic finite element analysis of stiffness, strength and obturating performance of the optimized obturator of the breech me chanism is performed

    利用優化后的結構參數建立了優化后炮閉氣結構的裝配三維幾何實模型和有限元模型,對優化后的炮閉氣結構剛強度和閉氣性能進行了準靜態及動態多接觸彈塑性有限元分析。
  3. The humidity sensitive characteristics of these sensors prepared by means of self - assembly have been investigated and the effects of electrode structures, concentration of humi - sensing solution, number of bilayers, materials of the outer layer and inner layer on humidity response were discussed

    測試了不同系濕敏膜的感濕特性,探討了電極結構、感濕液濃度、離子強度除電翻動復合膜層數、最外層材料、最內層材料等因素對濕敏元件響應特性的影響。
  4. 4 ) the method for rapid implementation of parameterized modeling of geometry and finite element of structure through a universal cae software ( msc. patran ) is researched, and parameterized modeling of the obturator of the breech mechanism is accomplished using the method

    研究了在通用cae軟( msc . patran )環境下,快速實施結構幾何和有限元參數化建模的方法,並對炮閉氣結構實施了參數化建模。
  5. Application of structural optimization and nonlinear finite element technique to nonlinear multi - component structural system ( assembly ) is studied for the sake of the obturator of the breech mechanism of an automated mortar. the method and technology for optimizing nonlinear multi - component structural system with contact is mainly researched in this thesis

    以某自動迫擊炮炮閉氣結構為背景,對結構優化與非線性有限元技術在多構件非線性結構(裝配)系統中的應用進行研究,著重在對存在接觸關系的多構件非線性結構系統進行優化設計的方法和技術途徑方面進行了研究和探索。
  6. 3 ) a 3 - d geometry and finite element model of the assembly of the obturator of the breech mechanism is established. quasi - static and dynamic finite element analysis of stiffness, strength and obturating performance of the obturator of the breech mechanism is carried out, based on elastoplastic theory and multi - body contact algorithm, and the simulation results coincide with experimental results, further, th e effect of friction factor on its obturating performance is investigated

    建立了炮閉氣結構的三維裝配幾何實模型和有限元模型,對炮閉氣結構剛強度和閉氣性能進行了準靜態及動態多接觸彈塑性有限元分析,分析結果與試驗結果相吻合,進一步研究了摩擦系數對其閉氣性能的影響。
  7. Success in optimizing the obturating performance of the obturator of the breech mechanism shows that the method and technology for optimal design of nonlinear multi - component structural system with contact put forward in this thesis is effective and practical. structural optimization problems that are difficult to solve through the optimization method available in the universal cae software can be accomplished by means of this method

    對炮閉氣結構閉氣性能優化的成功說明了本文提出的對存在接觸關系的多構件非線性結構(裝配)系統進行優化設計的方法和技術途徑具有實用價值,可以解決在通用cae軟中現有優化演算法難以解決的結構優化問題。
  8. This paper also presented the structure of soi bjmosfet and discussed and analyzed the advantages of this device by comparing with the bulk bjmosfet. its advantages are as fellow : no latch - up effect, better capability of resisting invalidation, much smaller parasitic capacitance, weaker hot - carrier effect and short - channel effects, and simpler technics, and so on

    通過與硅bjmosfet比較,討論和分析了soibjmosfet的優點:無鎖效應、抗軟失效能力強、寄生電容大大降低、熱載流子效應減弱、減弱了短溝道效應、工藝簡單等。
  9. Prof. of electrical engineering : kiss is n - type, the latch - up phenomenon in mos

    電機教授:接吻是一種n型金屬氧化物半導間的閉鎖(鎖存;鎖;鎖上)現象。
  10. The design concept of the automatic security shutoff is a hinged door closing onto a knife - edged seat fully contained in a high - grade ductile iron body ( or steel casting )

    自動安全關斷的設計原理是由內置於高品質延性鑄鐵?或鑄鋼?閥,以鉸的閥門閉鎖在一具有刃緣的閥座上。
分享友人