閉合公差 的英文怎麼說
中文拼音 [bìgěgōngchā]
閉合公差
英文
close tolerance- 閉 : Ⅰ動詞1. （關; 合） close; shut 2. （堵塞不通） block up; obstruct; stop up Ⅱ名詞（姓氏） a surname
- 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
- 公 : Ⅰ形容詞1 （屬于國家或集體的） state owned; collective; public 2 （共同的;大家承認的） common; gen...
- 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
- 閉合 : close; shutting; synizesis; synezesis; occlusio; closure; make; occlus-; occluso-
-
Although diss in many countries take fdic as the original version, and their basic objectives are the same on the whole, which are safeguarding the depositors " interests, especially the most depositors " interests who have less deposits, setting up a reasonable procedure with which the banks having serious problems and b eing closed to fail can be disposed of, strengthening the public ' s confidence with banks and keeping the bank system stable, there are many differences among them because of the different national conditions
盡管這些國家多以美國的聯邦存款保險公司為藍本，且基本目標相同，即保護存款人利益，尤其是保護居於多數的小額存款人的利益；建立對出現嚴重問題的瀕臨倒閉的銀行進行處置的合理程序；提高公眾對銀行的信心，保證銀行體系的穩定，但由於具體國情不同，各國的存款保險制度存在較大差異。Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc
本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。One is, based on answering the above open problem on a finite dimensional euclidean space by means of partially ordered theory, to research the existence of solutions, global error bounds of proximal solutions and sensitivity of parametric unique solutions and present a class of variable - parameter three - step iterative algorithms for generalized set - valued variational inclusion problems by using - resolvent operator of set - valued mapping. two is to consider the convexity, closedness and boundedness of the solution set of general set - valued variational inclusion problems and the sensitivity of the parametric solution set by means of graphical convergence theory. three is to discuss directly the existence of solutions by using analytical methods for set - valued mixed quasi - variational - like inequalities and suggest a class of direct variable - parameter three - step iterative algorithms for solving generalized set - valued variational inclusions
研究分有三個方面：一是藉助于偏序理論在有限維歐氏空間中解決了上述公開問題，在此基礎上利用集值映射的-預解運算元，研究了廣義集值變分包含問題解的存在性、逼近解的全局誤差界、參數唯一解的靈敏性，並提出了一類變參數三步迭代演算法；二是藉助于圖收斂理論研究了一般集值變分包含問題解集的凸性、閉性和有界性以及參數解集的靈敏性；三是用分析的方法直接討論了集值混合擬類變分不等式問題解的存在性並提出了一類求解廣義集值變分包含問題的直接變參數三步迭代演算法。
分享友人