閉環伺服機構 的英文怎麼說

中文拼音 [bìhuáncìbìjīgòu]
閉環伺服機構 英文
closed loop servo
  • 閉 : Ⅰ動詞1. （關; 合） close; shut 2. （堵塞不通） block up; obstruct; stop up Ⅱ名詞（姓氏） a surname
  • 環 : Ⅰ名詞1 （環子） ring; hoop 2 （環節） link 3 （姓氏） a surname Ⅱ動詞（圍繞） surround; encircle;...
  • 服 : 服量詞（用於中藥; 劑） dose
  • 機 : machineengine
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 機構 : 1 [機械工程] （機械的內部構造或一個單元） mechanism 2 （機關; 團體） organ; organization; institu...
  1. Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc

    本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。
  2. The micro displacement servo system includes step - electromotor, step - electromotor driver, grating displacement sensor and gearing etc. the closed loop position servo system eliminates machining error, fitting error and backhaul error etc. the control will completely run in the platform of windows

    微位移控制系統由步進電動機、步進電動機驅動器、光柵位移傳感器、傳動機構等組成，採用閉環位置伺服控制消除了傳動機構的加工誤差、裝夾誤差、回程誤差等。
  3. The other way, theoretical analysis of weld tracking system with a leading sensor is stated, based on the analyzing of movement process of the tracking system, a loop control structure diagram is presented, the deuce vision feedback system is used and realized the repeated and automatic tracking in multiplayer seam and controlling of system of tracking and system of motion

    同時就傳感器超前檢測式焊縫自動跟蹤系統進行了深入的理論分析，在分析該系統跟蹤過程運動關系的基礎上，建立了系統的閉環控制關系圖，並提出了其系統數學離散控制結構簡化圖。採用兩點式視覺伺服反饋系統，實現機器人在多層多道焊接時的重復自動跟蹤以及跟蹤機構的控制和焊炬橫向調節機構的控制，並使之協調聯動，滿足焊接過程的要求。
  4. The rotation control technology in the laser gyro strapdown inertial navigation system was studied. the method of realizing closed - loop digital control with rlg located in the strapdown inertial navigation system was discussed. the structure of rotation servo system was introduced. the designing method and process of the digital controller were given. the method of implementing digital controllers by means of computer and software flow were demonstrated. the result of simulation and debugging of this system showed that it fullfills the requirment of the strapdown inertial navigation system. it assures the stability of rotation and solves the problem of striking without increasing the volume and cost of the system

    研究激光捷聯慣導系統中的轉位控制技術.採用捷聯慣導系統本身的rlg實現轉位系統的閉環數字控制，給出了轉位伺服系統的結構組成以及數字控制器的設計方法和設計過程，給出了數字控制器的計算機實現方法和軟體流程.模擬及調試結果表明，所設計的轉位伺服系統滿足捷聯慣導系統的要求，既保證了轉動的平穩性，克服了到位撞擊問題，又不增大體積、增加成本
  5. Piezo - electrical ultrasonic motors were used to drive the linear slideways supported by the cross roller bearings, position information was fed back by the optical encoders, the total closed - loop control system was constituted

    伺服機構採用壓電超聲電機直接驅動由滾柱導軌支承的直線工作臺，通過高精度光柵尺構成全閉環反饋。
  6. This paper studies an ac servo system with the permanent magnet synchronous motor ( pmsm ) as the executive component. the disadvantages of the conventional methods of ac servo system are demonstrated by computer simulation and by analyzing the mathematical models of the pmsm and the vector decoupling control strategy. then, an improved double - pi combined with variable structure servo controller is proposed

    通過對永磁同步電動機的數學模型和矢量解耦控制策略的理論分析，以及基於雙pi結合單p位置調節的伺服系統的模擬實驗，揭示出經典的伺服控制方法的缺陷，並提出了一種改進的雙pi結合變結構的三閉環調節的伺服控制器設計方案。
  7. Piston ring is the important accessory of the engine and turning its contour is the key procedure to ensure the performance of piston ring it has great value in economy and society that we develop the nc machining system for outer circle of piston ring to manufacture the high quality piston ring and to replace the import machine according to piston ring contour data provlded by the cad system ， it can turn the piston ring contour by controlling the displacement of servomechanism which is controlled by the angle of servo motor it uses the theories of velocity closed loop 、 dlsplacement closed loop and feed forward control to improve the control precision of system on the basis of theories of elastic mechanics and mathematics ， the cad system can provide the accurate data required by the nc machine system according to the calculation model and the parameters of piston ring this system integrates the cad cam technology

    系統根據活塞環cad系統生成的介面數據，通過伺服電機的轉角位置控制自主研製的高性能微位移進給機構產生給定的位移，以完成活塞環輪廓的仿型加工。系統採用速度、位置閉環控制及前饋控制理論，以提高系統的控制精度。活塞環cad系統以彈性力學和數學方法為基礎，根據常用的計算模型與活塞環參數自動生成數控加工系統所需的精確的介面數據，實現cad / cam一體化。
分享友人
分享到 Line

分享到臉書