間隙流量 的英文怎麼說

中文拼音 [jiānxìliúliáng]
間隙流量 英文
clearance flow
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 隙 : 名詞1 （縫隙; 裂縫） crack; chink; crevice 2 （空閑） gap; interval 3 （漏洞; 機會） loophole; op...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 間隙 : （空隙） interval; gap; freedom; space; [機械工程] clearance; separation; stricture; clear; inter...
  • 流量 : rate of flow; flow; runoff; discharge; throughput; （flow） rate; quantity （of flow）; flux
  1. Based on the ostwald - de waele equation, the leakage characteristics of power - law transmitted by helical gear pump are researched, and the leakage model of power - law in the clearence is founded, and - the velocity distributing and the leakage capacity are worked out by the boundary condition. the power loss of leakage is got through the clearence leakage capacity, and the friction power loss is attained by the velocity distributing. the mathematic calculation model

    利用冪律流體本構方程，首次對聚合物流體在斜齒齒輪泵中的漏流特性進行了研究，建立冪律流體在間隙中的泄漏模型，利用邊界條件求出速度分佈及泄漏量；由間隙泄漏量得到漏流損失功率，由速度分佈得到流體摩擦功率損失，並得到間隙最優解的數值計算數學模型，同時給出實例及數值計算結果。
  2. Exchange non - clearane metal oxidate matter arrester is suitabe for the voltage protection of transformer switch cupboard, vacuum switch etc

    交流無間隙金屬氧化物避雷器，適用於變壓器、配電屏、開關櫃、真空開關、輸電線路、電力計量箱、並聯補償電容器、旋轉電機等電壓保護。
  3. Based on the special property of magnetic fluid ( mf ), we fill the magnetic fluid into the working clearances of the servo valve torque motor. one side, the magnetized magnetic fluid can exert a damping torque on the torque motor armature and reduce vibration of the armature ; on the other side, it can improve the magnetic circuit efficiency of the torque motor because of the magnetic fluid ’ s larger magnetic permeability

    基於磁流體所具有的特殊性質，將磁流體添加到伺服閥力矩馬達的工作間隙中，一方面磁流體被磁化后可增大銜鐵的阻尼力，減少振動;另一方面由於力矩馬達氣隙中磁導率的提高，使氣隙中的磁通量增大，力矩馬達的磁路效率和輸出扭矩將增大，因此可以提高力矩馬達的固有頻率和伺服閥的響應速度。
  4. The second part consist of chapter four. in chapter one, we study the energy density of harmonic map from finsler manifold and generalize classical result in [ se ]. in chapter two, we obtain lower estimates for the first eigenvalue of the laplace operator on a compact finsler manifold, and it generalize lichnerowicz - obata theorem [ li ] [ ob ]. in chapter three, we derive the first and second variation formula for harmonic maps between finsler manifolds. as an application, some nonexistence theorems of nonconstant stable harmonic maps from a finsler manifold to a riemannian manifold are given

    第一章討論finsler流形到黎曼流形調和映射的能量密度的間隙性，推廣了[ se ]中的結果。第二章對緊致finsler流形上laplace運算元的第一特徵值的下界作了估計，推廣了黎曼流形上的lichnerowicz - obata定理[ li ] [ ob ] 。
  5. According to non - newtonian fluid mechanics theory and mathematical method, conbined with plunger moving property, the hypothesize fluid is imcompressive, hydraulic radius of flow of liquid in crevice is very little, and it is laminar flow, the flow is treated fixed continuous flow at every instant position of plunger, equation of motion and boundary condition were set up in condition of concentric and eccentric of pump barrel and plunger

    運用非牛頓流體力學理論和數理方法，結合抽油泵柱塞運動特點，假設液體為不可壓縮的，液體在縫隙中流動的水力半徑很小，呈層流流動，柱塞在每一位置的瞬間，流動做定常流處理，建立了泵筒與柱塞同心和偏心兩種情況下運動方程和邊界條件，引入無量綱坐標、無量綱速度和柱塞與泵筒偏心配合時的縫隙高度，並給出縫隙流流速、流量的解析解。
  6. It has been confirmed practically that the diamond highness above base material can be adjusted with the range when the generator is put into use, and the result shows that the current density drop sharply with the increase of machining gap

    結果表明，間隙值的擴大伴隨電流密度的顯著下降，檢測電解電流控制脈沖能量的方法對實現電蝕層厚度基本可控是可行的，可讓金剛石突出一定高度。
  7. The flow between two gaps in the new type of axial trust balancing device was assumed as laminar move, and the flowing physical model in these two gaps was simplified into laminar move in the gaps between two parallel plates

    摘要將新型軸向力平衡裝置兩個間隙中的流動假設為層流，並將兩個間隙流動的物理模型簡化為平行板間隙的層流運動，推導出了徑向間隙與?漏量關系式和考慮離心力效應時軸向間隙與?漏量的關系式。
  8. The equipment adopts centrifugal sliding plow groove rotor and is the newest structure evaporator at present. it can form membrane under the condition of small flow. comparing with that of fixed space drag evaporator, its evaporation capacity can increase 40

    本設備採用離心式滑動溝槽轉子，是目前國外最新結構蒸發器，在流量很小的情況下也能形成薄膜，在簡體蒸發段內壁表面附著處理液中的淤積物可被活動刮板迅速移去，和固定間隙的刮板蒸發器相比，蒸發量可提高40 69 。
  9. Abstract : this paper uses the topology theory to analyze the surface flow spectrums of straight, positively curved and negatively curved cascades with relative tip clearances of 0. 023 and 0. 036, finds apparent differences of topology and vortex structures in the blade tip and the suction side wall corner of single type of cascade with this two clearances, and studies the mechanism of the difference formation as well as their effects on the energy loss

    文摘:應用拓撲原理分析了葉頂相對間隙為0 . 023和0 . 036的渦輪直葉柵和正、反彎葉柵的壁面流譜，發現在兩種間隙下同類葉柵的拓撲與旋渦結構在葉頂和吸力面壁角明顯不同，探討了差別形成的機理及其對能量損失的影響
  10. According to the experimental parameters of mpt, the main performance parameters of different propellants have been given by engineering performance computation under designed and working states, which has great importance for the experimental research and the future work. 2. for helium and argon, the factors which influence on mpt ' s vacuum steady work have been discussed such as the material of microwave tie - in, the distance between the probe and inner - conductor, the position of the inner - conductor, the input power of microwave, the mass flowrate of propellant and the vacuum pressure of environment, and the influence has been discussed of the microwave power and the mass flowrate of propellant on the pressure of the resonance cavity, thrust, reflected power and the temperature of the resonance cavity

    論文的工作和新見解主要包括： 1在設計狀態和工作狀態下，根據mpt的實驗參數，對mpt使用不同工質時的性能進行了工程估算，這對mpt現階段的實驗研究和今後的研究有重要的指導意義； 2對于he 、 ar推進工質，討論微波的接頭材料、探針與內導體的間隙、內導體的位置、微波的輸入功率、工質的質量流量以及環境真空度對mpt真空啟動和穩定工作的影響，並探討微波的輸入功率、工質的質量流量對諧振腔壓強、推力、反射功率以及諧振腔溫度的影響； 3對于n _ 2 、 h _ 2 、 nh _ 3 、 h _ 2o推進工質，主要討論與he 、 ar工質不同的特性，並從長遠的眼光和工程應用的角度，認為其可行性不容置疑，潛在優勢不可忽略，是未來mpt應用的主流推進工質。
  11. The derivation of the leakage flow rate formula of the special annular clearance between the piston and cylinder under condition of variable viscosity in the axial piston pumps was carried out. at same time, considering the questions of the eccentricity and the variable sealing length of piston friction pair, the modified coefficient of the calculation formula of the flow - rate of the leakage was given

    在變粘度、柱塞偏心以及變密封長度條件下，對軸向柱塞泵中柱塞與缸孔之間的特殊圓環縫隙的泄漏流量公式進行推導，得到了該計算公式的修正系數； 6
  12. The distribution of the gas - flow speed is measured at a position 1cm away from the outlet ( the end with larger air - gap ). it is illustrated that the gas - flow speed keeps increasing from the out surface of the inner sleeve to the inner surface of the outer sleeve, and then it decreases gradually

    測量了楔形氣隙流體出口（大間隙埠）外1厘米處空氣流速大小的分佈，發現空氣流速自轉子（內筒）壁面處開始逐步增大，至定子（外筒）壁面處達到最大值，隨后開始減小。
  13. By improving surface condition of parts and one shot seal - off clean room grade, using ultrasonic vapor phase cleaning process, the inner parts of vacuum interrupter get cleaner. movable particles have been diminished by automatic current ageing, power frequency hi - voltage ageing and dynamic high current ageing. as the dielectric strength of clearance in vacuum interrupter improved, the probability of re - ignition in test drops evidently

    通過提高零件表面加工質量，改善一次封排間的真空衛生條件、制定合理的超聲波氣相清洗工藝提高管內潔凈度，採用自動電流老煉、超高壓工頻老煉、大電流動態老煉等工藝進一步消除真空滅弧室內活動性微粒，可提高真空滅弧室真空間隙介質強度，使真空開關投切電容器組的重燃率大大降低，並通過實驗驗證真空開關投切電容器組的重燃率在製造工藝改進後由原來的10 . 7 %降低至1 . 3 % 。
  14. This new technology changes from the traditional method by which the induced and compressor wheel separately are designed and produced to a new one by which the one - piece compressor is designed. on the basis of this new technology and the optimum blade profile, the performance of both the compressor and the turbocharger is largely improved. through the heating power calculation of the compressor, the analysis of the surge and the block of the compressor, the test - bed performance test of the turbocharger, the matching test of turbocharger and diesel engine, the propulsion test of the turbocharger on plateau condition, it is proved that the newly - designed compressor not only has high efficiency, but also improves the flow distribution in the high efficiency area so that the propulsion line can run through the high efficiency area

    主要內容包括：提出一種全新的壓氣機葉輪技術和概念，這種技術將傳統的導風輪和壓氣機分開設計、單獨加工改為整體設計、整體加工的單體葉輪；從增壓器與柴油機配機計算所得出的基本參數出發，通過對壓氣機進行熱力計算，確定壓氣機的基本結構參數；再對葉型以及葉輪輪廓與葉輪罩殼的配合間隙進行優化，對新設計的壓氣機進行喘振和堵塞分析；通過增壓器平臺性能試驗，驗證了新設計的壓氣機的性能水平得到了較大的提高，達到了提高增壓器的整體性能水平的目的；通過增壓器與柴油機配機試驗、以及增壓器用於高原條件下的牽引試驗，驗證了新設計的壓氣機不但具有高效率，還改善了高效率區的流量分佈，使牽引特性線貫穿高效率區。
  15. This effect was gradually decreased with the increase of snte content in the pseudo - binary alloys as well as the increase of temperature, which is considered to be caused by the change of scattering mechanism, the saturation of carrier concentration as well as the ag atoms occupying the

    隨著膺ti合金rfsnte含量和測試溫度的上升， ag摻雜的作用逐漸降低，胸二兒合金的性能逐漸惡化。其原因被認為是由於散射機制的改變、載流子濃度趨于飽和以及ag作為間隙原一了提供額外施主。
  16. Brush question groove, the gap should maintain a certain amount of time to prevent the groove was dry on the second time, it would crash fat from the surface flow, the decline in the quality

    待第一遍刷完后，應保持一定的時間間隙，防止第一遍未乾就上第二遍，這樣會使漆液流墜發皺，質量下降。
  17. It was found that the ultra - fine powder can flow smoothly in a spouted bed with a draft tube under some sorts of design parameter and operating condition, thus a new effective method to improve fluidization quality of the ultra - fine powders is obtained ; at higher supplied gas velocity, an increase in the solid circulation rate is observed ; the extent of the distance between the nozzle and the draft tube inlet result in the promotion of the solid circulation rate ; the solid circulation rate increase with increasing the draft tube diameter or the bed mass ; the gas bypassing is nearly zero in the present work ; and the solid flow in the annulus is observed as a moving bed

    結果表明：在一定的床層結構和操作條件下，超細粉可以在導向管噴動床中實現平穩流化，從而為改善超細粉的流化質量提供了一種有效的新方法；固體循環速率與噴動氣流量、導向管直徑、導向管底部與噴嘴出口間距以及床層裝填量成正比；氣體則基本上不存在「旁路」現象；環隙區中的顆粒流動表現為一移動床特徵。
  18. An energy controllable ecm pulse generator which machining gap appearance changes with the detected eum current variable is developed, to make the electrolysis thickness of ecm and machining gap width of the diamond controllable

    用檢測電流的方法，設計和研製隨間隙狀態變化能量可控的脈沖電解電源，用於金剛石節塊電解修刃，以實現電解電蝕層厚度的基本可控，從而可實際控制金剛石的出刃高度。
  19. In this study we analysed the interactions between initial lymphatic and interstitium, examined the procedure of lymph formation, developed the interaction theory for lymph formatoin, and showed that not only interstitial fluid prssure but also normal stress of interstitial solid phase should be considered and that lymph flow rate is greatly affected by interstitial porosity

    分析了初始淋巴管與間質的相互作用，考察了淋巴液形成過程，提出了淋巴液形成的相互作用理論，說明了不僅要考慮間質流體壓力，還要考慮間質固相法應力及總應力，才能了解淋巴液的形成機理，間質孔隙度則直接影響著淋巴流量。
  20. The disposal of the valves and intake manifold structure not only affect fresh air charge but airflow in the cylinder, which immediately affect combustion efficiency and the performance of dynamic, economic and emission. the structure of the air distributing institution has influence on charging efficiency and the noise of engine. the combustion chamber affects compression scale which has great influence on dynamical performance ; f / v which affects the exhaust of hc ; squash area and clearance which have great influence on the intensity of squash

    氣缸蓋的氣門排列方式與氣道結構形式影響進氣充量和氣流在氣缸內的運動，從而影響了燃燒效率，對整機的動力性、經濟性以及排放都有直接的影響；配氣機構的形式影響充氣系數和整機噪聲等；缸蓋燃燒室決定了影響整機動力性能的壓縮比，影響hc排放的f / v和對擠流起決定性作用的擠氣面積以及擠氣間隙，所以燃燒室對整機動力性、經濟性、排放等都有重要的影響；氣缸蓋是整機熱負荷與熱應力最大的部件之一，熱負荷過高將不利於發動機壽命以及可靠性的提高。
分享友人
分享到 Line

分享到臉書