閥桿環 的英文怎麼說

中文拼音 [fágǎnhuán]
閥桿環 英文
stem ring
  • 閥 : 名詞1 （指在某方面有支配勢力的人物或家族） established house or power group; a powerful person or...
  • 桿 : 桿名詞（桿子） pole; staff
  • 環 : Ⅰ名詞1 （環子） ring; hoop 2 （環節） link 3 （姓氏） a surname Ⅱ動詞（圍繞） surround; encircle;...
  1. One machinery makes wen zhoudong limited company is to be engaged in research, development, production, sale is domestic and international the gas a powerful person of all sorts of medium compressor, a powerful person piece, lever of annulus of bedspring, piston, piston, piston, sealing ring, crosshead, crosshead is sold, copper is covered, bolt of connecting rod, connecting rod,

    溫州東一機械製造有限公司是從事研究、開發、生產、銷售國內外各種介質壓縮機的氣閥、閥片、彈簧、活塞、活塞環、活塞桿、密封圈、十字頭、十字頭銷、銅套、連桿、連桿螺栓、軸瓦、曲軸、缸體及缸蓋、缸套、凈化設備及部件、冷卻器等壓縮機配件的專業技術型企業。
  2. Additionally, it has utilized the harvest of the diffluent and confluence cross experiment made by beijing university of technology, which has enhance the application of the software and be of innovation

    同時，軟體利用了北京工業大學建築環境與設備實驗室多年來在帶調節拉桿閥片的合流及分流四通局部阻力系數的實驗研究成果。這一點，將擴大了軟體的工程應用范圍。
  3. There is no clutch, gearing, oil changes, smog check, pistons, rings, valves, crankshaft, flywheel, rods, wrist pins, etc., etc

    沒有離合器，傳動裝置，機油變化，尾氣檢查，活塞，活塞環，閥門，曲軸，飛輪，連桿，肘節銷，等等。
  4. Insert stem assembly ( a ) and hold disc on seat ring in closed position, as shown

    插入閥桿總成（ a ） ，並在關閉狀態下握住閥座環上的閥瓣，如圖所示。
  5. All sizes are standardly equipped with awwa epoxy coated, ul / fm listed osy resilient seated gate valves, cfm ( cubic feet per minute ) or gpm ( gallon per minute ) meter and ball type test cocks

    作為標準配置，所有通徑美國自來水廠協會（ awwa ）認可的環氧樹脂塗敷， ul / fm認證外閥桿軛架彈性閥座閘閥， cfm （立方英尺/分鐘）或gpm （加侖/分鐘）水表和球型測試旋塞。
  6. The valve stem with its grooved rings and positioning sleeve indicates the throttled position of the valve

    閥桿及其溝槽環和定位套筒顯示閥門的節流位置。
  7. Hydraulic concrete crusher detail : all round, extremely efficient concrete crusher system for concrete demolition in general, and reinforcement exposure in particular. the system works immissionfree, i. e. : it does not produce any noise, dust or cibrations and operates without water. description : pliers qty 1, hydraulic power pack qty 1, 10m long oil pipe set of hoses, high pression qty 2, accessories bag qty 1

    啟動電機帶動油泵運轉，液壓油直接返回油箱手動轉動換向閥三位四通閥一個位置后，液壓油進入系統推動活塞，活塞桿伸出，帶動鉗體收縮，從而破碎鋼筋混凝土結構，反向轉動換向閥，鉗體松開，完成一個工作循環。
  8. Disc stem nut : disc stem ring connects the disc to the stem, permitting the disc to swivel and aid in securing tight seating for trouble - free service

    閥瓣閥桿螺母：閥瓣閥桿環將閥瓣連接到閥桿上，使得閥瓣能夠旋轉，並有助於保證閥座地緊密密封和無故障運行。
  9. Two o - rings in gland follower provide additional stem seal protection to assure tightness of less than 1 ppm

    密封壓蓋隨動件內的兩個o形環為閥桿提供更加安全的密封保護，以確保泄漏率不會超過百萬分之一。
  10. When the temperature to gas pipelines, temperature packets of material expansion, the pressure rise, inflation pressures are rising corrugated box, corrugated promote the expansion thrust to overcome the spring - loaded pole resistance, the ball - type valve opened for big change ; when the gas pipeline to reduce the temperature, temperature of the material swelling up, the pressure lowered inflation corrugated box pressure also reduced, spring - loaded pole compressed corrugated of resistance to thrust, spherical valves open for smaller ; this constant push and pull adjustment for the balance, as long as refrigeration cycle continue

    當回氣管道溫度升高，感溫包內的物質膨脹，壓力升高，膨脹波紋箱內壓力也升高，波紋腔膨脹推動推力桿克服彈簧阻力，球型閥開度變大；當回氣管道溫度減低，感溫包內的物質膨脹，壓力降低，膨脹波紋箱內壓力也降低，彈簧阻力推動推力桿壓縮波紋腔，球型閥開度變小；如此不斷的進行推拉調整平衡，只要製冷循環繼續下去。
  11. The handwheel can be removed and repositioned any of six positions around the stem

    手輪可以拆卸並重新定位在環繞閥桿的六個位置中的任何一個位置上。
  12. Nickel plated overlay in stem hole for carbon steel valves to combat severe alkylation conditions

    碳鋼閥門採用閥桿孔內鍍鎳層的閥桿，適用於嚴酷的烴化應用環境。
  13. Then, lubricate the stem and slide top of the elastomeric seat over the top ( long end ) of stem and push down over the o - rings

    然後，在閥桿上加潤滑油，在閥桿頂部（長端處）滑動彈性材料閥座的頂部，將其推到o形環上。
  14. For applications requiring handle removal, the d - ring stem flats indicate “ open / close ” and a molded - in arrow on top of the stem indicates flow direction

    由於實際應用中可能需要拆卸手柄，因此d形環閥桿平面表示「啟閉」 ，閥桿頂部的的模鑄箭頭表示流向。
  15. Nickel plated overlay on backseat in stem hole to combat severe alkylation conditions

    在閥桿孔內的後座上鍍鎳，可應用在嚴酷的烴化環境。
  16. Suitable for each type of dual - surface molding, for example, spring end, bearing, magnet, connecting rod, piston ring, compressor valve and etc

    適用於各種雙面加工例如：彈簧端面培林磁鐵連桿活塞環壓縮機閥片等。
  17. It has two stem sealing : one is stuffing box and another is toroidal sealing ring ( o - ring )

    本閥閥桿密封分為兩種形式：一為填料密封；一為o型密封環密封。
  18. Turn the brass memory lock ring until the aluminum memory ring stop contacts the step on the valve stem. do not overtighten. finger - tight pressure is sufficient

    旋轉黃銅記憶鎖環直到鋁記憶環停止接觸閥桿上的臺階為止。不要過緊。手指旋緊壓力已經足夠了。
  19. Remove the relief valve assembly ( includes cover o - ring, stem and diaphragm assembly )

    拆卸安全閥總成（包括閥蓋o形環，閥桿和隔膜總成） 。
  20. They can also be installed in vertical or horizontal pipe runs with the stem other than vertical, but may require special construction depending on valve size, service conditions and materials

    也可以安裝在垂直管道或者閥桿不是垂直向上的水平管道上，但是根據閥門的通徑大小、應用環境和材料的具體情況，可能要求特殊的結構。
分享友人
分享到 Line

分享到臉書