閥載導閥 的英文怎麼說
中文拼音 [fázǎidǎofá]
閥載導閥
英文
piggyback pilot valve-
The lateral diffusion of the photo - carrier in photoconductor layer is one of the important factors of affecting the resolution of lclv
液晶光閥的解析度與許多因素有關，而光導層光生載流子的橫向擴散則是其中的重要因素之一。The parallel seat gate assembly consists of two interchangeable spring loaded discs, a fully guided disc carrier, and retaining pins
平行閥座閘閥由兩個可互換彈簧負載閥瓣，一個全導向閥瓣托架和扣環銷釘構成。Parallel seat gate and seat ring construction can be furnished for high differential pressure services or where high piping loads or thermal expansion may cause sticking of a wedge type gate
平行閥座閘閥和閥座環結構可以應用在高壓差應用環境中，或者高管道負載，或可能導致楔形閘板閘閥卡住的熱膨脹應用環境中。It will be known from the obtained expression of the resolution of photoconductor that the column microstructure is benefit to reduce the carrier diffusion in the lateral direction and increase the resolution of the photoconductor
這種各向異性的柱狀結構復合光導膜有利於減小光生載流子的橫向擴散長度，從而可以提高液晶光閥光導層的解析度。The principle and the application of liquid crystal light valve ( lclv ) and the development of the photoconductor of lclv have been reviewed in this paper. the growth mechanism of amorphous silicon film is analyzed. the resolution of the photoconductor that is affected by the lateral diffusion of the photo - carrier in photoconductor layer is also analyzed
本文介紹了液晶光閥光導層的發展、液晶光閥的工作原理及應用，分析了非晶硅薄膜的生長機制以及載流子的橫向擴散對解析度的影響，詳細研究了nc - si a - si ： h柱狀結構復合光導層液晶光閥的制備工藝。Servo loading valve is the pivotal part of the system, it is designed again in this thesis, the mathematical model of the system and its control parts was established and built. the author deduced how the system parameters and control method influence the system dynamic state through theoretical analysis of the system. in addition, the dissertation introduces how to carry out protection in event of sudden break down of the system
伺服加載閥為整個系統的關鍵元件，論文進行了加載閥的設計，其性能指標達到了理想要求，並完成了對系統關鍵元件及整個加載系統進行了建模與模擬，通過理論分析導出了系統結構參數和控制方法對系統動態性能及加載精度的影響，並進行了系統誤差分析。The transfer of the carrier in photoconductor is anisotropy owing to the column structure of the film is anisotropy. on the basis of the new concept suggested in this paper, the maximum diffusion length in the lateral direction of the photo - carrier in the photoconductor ( which is related to the resolution of lclv directly ) as function of conductivities of both in lateral and normal directions in the film can be obtained as the expression as following. the nc - si / a - si : h photoconductor of lclv deposited and crystallized at low temperature of exactly 250 c stack column structure by al inducing a - si : h
本文根據柱狀結構存在各向異性的特點，並根據半導體物理知識，推出光導層光生載流子橫向最大擴散長度（該擴散長度與液晶光閥光導層解析度直接相關）與薄膜橫向和縱向電導率關系的表達式為：由於a - si ： h在al金屬的誘導作用下在不高於250的溫度下即開始晶化，本文對用金屬al誘導非晶硅晶化制備的nc - si a - si ： h薄膜進行研究。That is, through analysis of the principle on flow control and " hydraulic transistor ", design and calculation of flow control characteristic as well as main parts in valve inner chamber, a piloted reducing valve will be installed between main valve and pilot valve. after a pressure - difference compensating reducing valve was added in the non - pressure compensating piloted reducing valve of the flow control valve in vlalvistor valve, the calculation on control characteristic emulation and load characteristic emulation has been carried out. the result of the calculation shows that after pressure compensating reducing valve was added, the linearity of the control characteristics has been greatly improved thus eliminating influence upon outlet flow by load pressure - change of the hydraulic system and improving performance characteristics of the hydraulic component
文章還在對瑞典valvistor閥的插裝比例閥研究的基礎上，提出了一種新的流量控制原理，即：通過對流量控制和「液壓晶體管」原理的分析、流量控制特性及閥內腔主要結構件的設計計算，在主閥和導閥之間增設先導減壓閥，並進一步對valvistor閥的流量控制閥之無壓力補償先導減壓閥、加入壓差補償減壓閥后的控制特性進行了模擬計算和負載特性模擬計算，結果表明：增設壓力補償先導增壓閥后，其控制特性曲線變得非常線性，從而消除了液壓系統負載壓力變化對主閥輸出流量的影響。分享友人