阻尼面 的英文怎麼說

中文拼音 [zǔnímiàn]
阻尼面 英文
damping surface
  • 阻 : 動詞（阻擋; 阻礙） block; hinder; impede; obstruct
  • 尼 : 名詞（尼姑） buddhist nun
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  1. The method proposed in this thesis do well in solving the problems of multi - damping - ratio - spectra simulation. it is convenient to obtain the pareto optimal solution set of the multi - object question by using implicit parallel genetic algorithms and the method can meet the practical needs for simulating ground motions coinciding with multi - damping - ratio - spectra in seismic design. the crossing rate and variance rate are important parameters of genetic algorithms which affect the rate of convergence, the adapting rate of cross and variation in this paper can auto - adapt and according to stand or fall of current sample, it assures the sample approach to the pareto optimal solution set in fast convergent speed

    較好地解決多阻尼比反應譜擬合問題；本文方法通過一次運行就能獲得一組具有集系特性的地震動，在擬合多阻尼比反應譜的人造地震波集系的模擬方面有傳統方法所不能比擬的優勢，產生的人造波或人造波集系可滿足工程抗震設計需要；在遺傳演算法中，交叉概率和變異概率是影響收斂速度的重要參數，本文採用的改進自適應交叉概率和變異概率，可以根據當前樣本的好壞程度來自動地選擇適當的交叉概率和變異概率，以保證演算法始終以較好的速度向pareto最優解集逼近。
  2. The aerodynamic characteristics of a projectile with wrap around fins are studied systematically in this paper, as follows : 1. the lift coefficients 、 drag force coefficients 、 pitch moment coefficients 、 pitch damping moment derivatives and roll damping moment derivatives are obtained from engineering calculation through looking wrap around fins as flat fins of the same projection aera

    本文對某卷弧尾翼彈氣動特性進行了系統研究，主要內容與結論為: 1 .將卷弧翼按照相同投影面積的平板翼進行工程估算，得到升力系數、阻力系數、俯仰力矩系數、俯仰阻尼導數、滾轉阻尼導數曲線。
  3. Iv ) revolute joint element, nonlinear spring - damper element, 3 - d 5 points contact element are applied to simulate the revolute restriction between two caterpillar boards, suspension nonlinear vibration, contact between wheels and caterpillar boards, and contact between caterpillar boards and ground are considered respectively. drucker - prager material is employed to simulate reinforced concrete

    4 、應用大幅度轉動約束單元、非線性彈簧阻尼單元、三維五節點接觸單元分別模擬自行火炮履帶板之間的轉動約束連接、懸掛非線性振動及負重輪與履帶板之間的接觸和履帶板與地面的接觸問題；根據材料非線性理論，提出利用drucker ? prager材料建立土壤的非線性有限元模型。
  4. ( 2 ) increasing of wind is mainly induced by shf and affecting of lhf is very little. ( 3 ) effect of terrain increases ground rough and tonsure of terrain press and fiction correspond enhance frictional damp effect

    （ 3 ）地形作用相當于增加了地面粗糙度，地形壓力梯度項與摩擦項地疊加，相當于使摩擦阻尼作用增大，地形強迫作用使下邊界層從上至下風速減小，風向向左偏轉。
  5. Based on extensive investigation of construction technique history of chinese ancient buildings, the structure method, structure developing history and seismic behavior of chinese ancient timber structure buildings are analyzed in several respects of the structural system and form. through a series of experiments on constituent parts of chinese ancient timber building structure, including the tests on the corbels and brackets called dougong subjected to low cyclic reversed loadings, the tests on the wooden frame using the tenon - mortise joints as connections of column and beam subjected to low cyclic reversed loadings, the tests on vibration isolation effect of friction and slippage between column footing and their socle base, and a series of shaking table tests on a chinese ancient timber structure palace building mode under artificial earthquake at serving conditions, destroyed conditions and reinforced conditions, many valuable results of structures such as moment - curvature hysteretic loops of dougong structure and tenon - mortise joints under low cyckc reversed loadings, the static function, the seismic performance, energy dissipation, vibration reduction, energy - loss mechanism, nechanicalmode and failure mode were studied. aplenty of valuable parameters of the structure system were obtained, such as the natural period of structure, vibration modes, damping ratio, factor of vibration isolation, oscillate amplitude of ineitial accebration, velocity and displacement, magnitude of slippage, and the mechanism of structure failure and collapse etc. based on these research, the complete analysis of ancient timber structure under earthquake were carried out in which including mechanism analysis method, calculating mode, strength analysis of members and joints, strengthening methods for serving damaged ancient timber structure buildings were also taken into account

    依照宋代《營造法式》建造了抬梁式殿堂木結構構件及結構模型，對中國古代木結構中的典型構造如：柱腳在礎石頂面平擱簡支、柱架榫卯連接、柱高不越間之廣、側腳、生起、斗拱等的構造機理及結構功能進行了量化分析和實驗研究： （一）通過木柱石礎靜摩擦試驗，測定了柱腳與石礎古鏡面間的摩擦系數及摩擦力隨上部結構荷載變化的規律； （二）通過單柱承載力試驗，測定了古建築中木柱的受力變形特徵、破壞模式、及模型材料的變形模量、極限承載力、極限變形等參量； （三）通過柱架低周反復荷載試驗，測定了柱架的抗側移剛度、柱架恢復力特性及滯回曲線、榫卯張角剛度及其變化規律、柱架及榫卯的極限承載力和極限變形、及榫卯減振參數； （四）通過斗?低周反復荷載試驗和受壓試驗，測定了古建築木構件與木構件間摩擦系數，斗?抗側移剛度，斗?恢復力特性及滯回曲線，斗?抗壓極限承載力及受力變形規律； （五）通過抬梁式殿堂間架模型振動臺試驗，測定了殿堂木構架結構自振周期，地震反應振形、阻尼特性及阻尼比；按結構分層特點對柱腳、柱頭和斗?層上的屋蓋的地震反應採用多點同步測量，對柱根滑移、榫卯變形、斗?的變形、復位、耗能減振參數等進行了定量分析。
  6. Compared with the passive car suspension, the semi - active car suspension system with the intelligent mr damper can control the damping force automatically with the computer control and then enhance the ride comfort and handling stability of the car effectively

    與傳統的汽車被動懸架系統相比，裝有磁流變阻尼器的半主動懸架系統，可以根據路面狀況和車輛運行狀態，在計算機的控制下自動調節阻尼力，大大提高了汽車乘坐的舒適性和行駛安全性。
  7. Those sensitive parameters making system have negative damping and occur self - excited shimmy are horizontal pulling lever rigidity, tire sideslip rigidity, steering gear rigidity and damping, kingpin equivalent damping, kingpin caster angle, tire drag. and wheel center distance, tire side rigidity, vehicle wheel unbalanced mass, tire vertical rigidity, and distance from kingpin center to the vertical central line plane of tire have great influence on shimmy, but they do n ' t make the system have negative damping. and horizontal pulling lever damping, suspension damping and rigidity have very small influence on shimmy

    橫拉桿剛度、輪胎的側偏剛度、轉向機剛度、轉向機阻尼、繞主銷當量阻尼、主銷后傾角、輪胎拖距是影響擺振的敏感性參數，適當調節某一參數可引起系統的負阻尼，使系統產生自激擺振；輪距、輪胎側向剛度、車輪上的不平衡質量、輪胎垂向剛度及主銷延長線與地面交點至車輪平面的距離對擺振的影響也較大，但不會使系統出現負阻尼；而橫拉桿阻尼、懸架阻尼與懸架剛度對擺振的影響很小。
  8. On one hand, it may exert damping on the armature of torque motor and overcome self - excitation of jet pipe. one the other hand, it may enlarge magnetic permeability of working clearances and improve magnetic circuit efficiency of torque motor to boost dynamic response speed of servo valve

    一方面可增大力矩馬達工作氣隙部分產生的阻尼，從而可以抑制射流管的自激，另一方面又可增大工作氣隙的導磁率，改善力矩馬達部分的磁路效率，從而提高伺服閥的動態響應速度。
  9. Based on the special property of magnetic fluid ( mf ), we fill the magnetic fluid into the working clearances of the servo valve torque motor. one side, the magnetized magnetic fluid can exert a damping torque on the torque motor armature and reduce vibration of the armature ; on the other side, it can improve the magnetic circuit efficiency of the torque motor because of the magnetic fluid ’ s larger magnetic permeability

    基於磁流體所具有的特殊性質，將磁流體添加到伺服閥力矩馬達的工作間隙中，一方面磁流體被磁化后可增大銜鐵的阻尼力，減少振動;另一方面由於力矩馬達氣隙中磁導率的提高，使氣隙中的磁通量增大，力矩馬達的磁路效率和輸出扭矩將增大，因此可以提高力矩馬達的固有頻率和伺服閥的響應速度。
  10. A 2dof vehicle structure model with mr damper is established, a sliding model controller is designed, and the real - time control damping force of suspension system is educed

    摘要建立了履帶車輛1 / 2車體振動模型，設計了相應的滑移面和滑移模態控制器，得出了履帶車輛半主動懸掛系統的實時控制阻尼力，並對路面激勵下滑模控制與最優控制的減振效果進行了模擬。
  11. Wear failure analysis of plasma spray coating on damping area of turbine blade

    渦輪葉片阻尼面等離子噴塗層磨損失效分析
  12. When calculating the damping coefficient of the section with the semi - submerged bow, the viscous effects are considered

    在計算帶有半潛首剖面的阻尼系數時，考慮到粘性的影響。
  13. The records we used are mainly from three parts : strong ground motion data before 1992 ' s ; data from scec ( south california earthquake catalog ) ; nsmp ( national strong motion project ). after we developed the attenuation laws, we analysis the attenuation characteristics for the pga and sa with different damping ratio. here we mainly concentrate on the effect of the distance and the magnitude

    在回歸出中小地震的衰減關系后，本文對峰值加速度（水平向與垂向） 、加速度反應譜（阻尼比分別為0 . 005 、 0 . 02 、 0 . 05 、 0 . 1 、 0 . 2 ）的衰減特性進行了分析，影響因素主要考慮了震級與距離這兩個方面。
  14. Through studying the working mechanism of the composing, the paper referred the bearing ' s analyzing model and designing flow. through shearing test of high damping rubber, the paper analyzes the influence of shearing shape, shearing strain range and inspiriting frequence on the characteristic parameters ( dynamic shear elastic module, dissipation engineering module, wasted gene ). according to the rule of equivalent energy, the paper gets the hysteretic curve of hdr ' s equivalent bilinear model and parameters ' calculating formula

    本論文通過對這種分離式減震支座各組成部分工作機理的研究，提出了該分離式減震支座整體的計算分析方法和設計流程；通過高阻尼橡膠剪切試驗，分析了高阻尼橡膠剪切面形狀、剪應變幅值、激勵頻率和試件高度對特徵參數（動態剪切彈性模量、耗能模量、損耗因子）的影響。
  15. Fist ly, use mass equivalent method to predigest the original rotor system. secondly, use transfer matrix arithmetic to have finished the relative program to calculate the critical speed of flexible multi - tray rotor bearing system by matlab language. thirdly. finish program the unbalance response using riccati - transfer matrix arithmetic and finity buck arithmetic. fourthly, answer to the high vibration of uncontroled system when cross the critical speed, come out to adopt changing clearance damper bearing to control the viberation

    本文對多柔盤轉子-支承系統的振動現象做了以下初步探索：用質量離散化方法把原轉子系統簡化；採用matlab語言編制了對傳遞矩陣法計算多柔盤轉子-支承系統的臨界轉速；用matlab語言對riccati傳遞矩陣法和有限元法編制了程序計算系統的不平衡響應；並針對其過臨界轉速時振動較大的現象，提出採用變間隙控制油膜剛度和阻尼，從而使原系統的在特定轉速（臨界轉速）的一段范圍內不平衡響應減小；並從被動控制與主動控制兩方面進行數值模擬，取的了較好的控制效果。
  16. A test has been carried out on three typical bridges sectional models of flutter derivatives to find the general rules with the change of flutter derivatives of the bridges sectional model. and it has been discovered that this change depend on the torsional damping, an element closely relating to the h * 2 and a * 2 4

    通過對三種典型斷面顫振導數的測試，考查了各顫振導數隨斷面形狀的變化趨勢，說明了最主要的變化體現在與扭轉阻尼有關的h _ 2和a _ 2項。
  17. The calculated drafts covers the whole possible ship draft in the large amplitude motion ; secondly, the research creates and solves the ship large amplitude motion equations. on the one hand, the actual calculation takes into account the coupling between the different motion modes, on the other hand, in the process of calculation of the ship hydrodynamic coefficient, it considers the influence of the nonlinear factor. the hydrodynamic coefficient used in the calculation of froude - krylov force, diffraction force and radiation force changes instantaneously following the draft, and the hydrostatic buoyancy is computed very accurately for the instantaneous immerse hull

    本文的研究分為二個部分：首先利用frank源匯法計算水動力系數，計算包括不同吃水時的附加質量和阻尼系數，吃水范圍涵蓋了船舶大幅度運動時所有可能的吃水；然後建立和求解船舶大幅度運動方程，在實際計算時一方面考慮了運動模態之間的耦合，另一方面在計算水動力時，考慮了非線性因素的影響。 froude - krylov力、輻射力、繞射力中的水動力系數隨吃水瞬時變化，靜浮力的計算精確到船體瞬時濕表面積，最後用四階龍格?庫塔方法在時域內求解船舶運動方程，並進行了載荷計算。
  18. On the basis of theoretic analysis and numeric calculation, the author verifies that only is the ratio of the fundamental period of the structure to the disturbance period beyond 1. 4, it ' s possible to achieve reductions in both the relative displacement and the absolute acceleration responses

    作者在此基礎上，從理論分析和數值計算兩方面證明了粘性變阻尼控制僅在結構周期與激勵主周期的比值大於1 4時才有可能同時減小結構的位移反應峰值和加速度反應峰值。
  19. After analysis of the parameters of the devices, a conclusion is achieved that we can directly use the parameters of the dampers instead of devices to design the buildings in the common situation. then a one - freedom modal is used to compare the differences of performance between these two dampers under harmonic load. finally, three buildings, which are installed with viscoelastic dampers, viscous dampers and no dampers respectively, are analyzed using finite element method, time history method and response spectrum method, and the result is the same as that of harmonic analysis

    如果支撐剛度較小，應採用本文推倒的公式計算阻尼裝置的性能參數；利用單質點模型進行阻尼結構在簡諧荷載作用下的性能分析，並比較了粘彈性與粘滯阻尼結構在振動控制方面的性能差異；最後利用數值方法分別對未安裝阻尼裝置結構，安裝了粘彈和粘滯阻尼裝置的三種結構進行了反應譜和時程分析，得到了與理論分析一致的結果。
  20. The calculation formula for structure damping exhausting factor of combined pipe is denoted. structure exhausting factor of combined pipe treated by the damping material of sa - 3 is obtained with the different temperature and damping layer thickness

    推導出管道表面阻尼處理后復合管結構損耗因子的計算公式，並得出了sa - 3阻尼材料處理后，不同溫度、不同阻尼層厚度時復合管的結構損耗因子。
分享友人
分享到 Line

分享到臉書