阻抗變換器 的英文怎麼說
中文拼音 [zǔkàngbiànhuànqì]
阻抗變換器
英文
impedance transformer- 阻 : 動詞(阻擋; 阻礙) block; hinder; impede; obstruct
- 抗 : Ⅰ動詞1 (抵抗; 抵擋) resist; combat; fight 2 (拒絕; 抗拒) refuse; defy 3 (對等) contend with...
- 換 : 動詞1. (給人東西同時從他那裡取得別的東西) exchange; barter; trade 2. (變換; 更換) change 3. (兌換) exchange; cash
- 器 : 名詞1. (器具) implement; utensil; ware 2. (器官) organ 3. (度量; 才能) capacity; talent 4. (姓氏) a surname
- 阻抗 : [電學] impedance
-
300 75 balun for fm and tv broadcast receiver
調頻電視廣播接收機用300 75平衡-不平衡阻抗變換器Negative impedance converter
負阻抗變換器This effects can be explained as follows : the radiation conditions are actually impedance matching condition in terms of microwave network, for a fixed dimension of a resonator and output transformer, only below the critical plasma density ", the matching condition can be satisfied in the smith circle map
我們提出,這一現象可從阻抗匹配的角度來解釋。對於一確定尺寸的腔體、阻抗變換器,存在一個等離子體密度的臨界值,只有在等離子體密度低於這個臨界值時,腔體的輸出阻抗和波導的特性阻抗才能滿足匹配,即滿足所謂的輻射條件。Impedance - matching balanced traction transformers ( balanced transformers in this paper for short ) are step - down transformers, they transfer symmetrical three phase voltage in primary side to perpendicular two phase voltage in secondary side. they are different from any other transformers, so their short - circuit current analysis and short - circuit test method must be taken into special account
阻抗匹配平衡牽引變壓器(本文中簡稱平衡變壓器)是一種將一次側三相對稱電壓變換為二次側二相垂直電壓的降壓變壓器,它不同於已有的任何一種變壓器,短路電流的分析計算和短路試驗必須予以重新研究。But to circular plate with large surface area, the vibrate modes generated is often so high that there is reverse phases existing, which result in a decrease in radiation impedance, electric - acoustic efficiency and the electric power, as well as poor directivity
然而對于輻射面積較大的彎曲振動圓盤,一般激勵的振動階數比較高,因此存在彎曲振動的反相區,導致換能器的輻射阻抗下降,電聲效率和聲功率降低以及指向性變差等問題。Changing the depth of penetration of the three dowels results in the variation of the reflection coefficient ( s1 1 ) at the port 1. using matlab, we can calculate different equivalent impedance of port 1 which resulted from the variation of dowels depth. the purpose of my work strike up a relationship between the depth of dowels and equivalent impedance at port, thereby accomplish matching rapidly, simultaneously and stably
在構建了自動阻抗匹配系統的基礎上,本文提出了一種新的快速匹配方法;此方法是將模擬軟體hfss和系統設計相結合,用hfss模擬系統中完成阻抗變換作用的銷釘匹配器,獲得銷釘插入波導深度變化時的埠等效特性,並將模擬得到的數據用matlab組織起來,分析銷釘插入波導的深度變化時埠等效阻抗特性的變化,來達到對調試變化規律的認識,快速的實現銷釘插入深度與反射系數間的統一。Some design guide lines are discussed based on the structure of the system. the mutual inductance coupling model of the system is introduced. the circuit impedance is analyzed
針對非接觸感應電能傳輸系統的構成,討論了非接觸感應電能傳輸系統的設計準則,介紹了變換器的互感等效電路模型,並進行了阻抗分析。A fem software as an important tool, work has been done as follows : the method using fem to design anomalous structure of transducers was adopted ; the vibration modes of the elastic pipe, ultrasonic transducers and system has been analyzed in piezoelectric coupled field. resonant frequencies of the transducers have been matched quite well with resonant frequencies of pipe, which can make it easy and accurate to design a transducer. the values of equivalent dynamic capacitors and dynamic inductances of ahead nine orders have been gotten derived by fem method, and fem equivalent circuit of the transducers has been built
以ansys有限元軟體為主要分析工具完成了設計工作;在經典換能器設計理論和前人經驗的基礎上,對不規則形狀的換能器採用了有限元的方法設計;在耦合場中分析了換能器、導管及整體裝置的振動情況,使換能器的諧振頻率與導管的諧振頻率達到了較好的匹配,使設計變得更加容易和準確;利用有限元方法建立了振子的等效電路模型,求出了其前6階模態的等效動態電容電感值,為阻抗匹配和驅動電路的設計提供了依據。Effect of changing the transducer impedance on the matching layer parameter
換能器輻射阻抗變化對匹配層參數的影響The mechanical impedance analyzing method utilized, the mathematical formula for the input impedance and transformer ratio of ultrasonic horn are built up, some vibration performance of ultrasonic horns are discussed under different load impedance, the relationship and applicational conditions between the transformer ratio of ultrasonic horn and the radiational impedance are analyzed
採用機械阻抗分析方法,建立了超聲變幅器的輸入阻抗和變幅比的數學表達式,討論了不同負載阻抗下超聲變幅器的振動性能,分析了超聲變幅器的變幅比與換能器輻射阻抗之間的關系及應用條件。Presents the simple but highly reliable on - line detection of ultrasonic transducer clamping capacitance based on the impedance circuit model constructed through the impedance characteristics of the ultrasonic transducer under triple harmonics, and concludes from experimental results that this method can be used to effectively detect the variation of clamping capacitance while the transducer is operating, and the matching inductance can be dynamically regulated according to the results of detection, and dynamic matching can therefore be achieved in the real sense at the end of the transducer to improve the overall performance of the whole system
為了解決大功率超聲應用的換能器電端匹配問題,分析了超聲波換能器在諧振頻率三次諧波下的阻抗特性,給出了超聲換能器三次諧波下的阻抗電路模型.並根據阻抗電路模型建立了對超聲換能器的夾持電容實現在線檢測簡單、可靠性高的方法,實驗證明該方法有效的.該方法可以在換能器工作過程中隨時檢測夾持電容的變化,根據檢測結果對匹配電感進行動態調整,實現真正意義上的換能器電端的動態匹配,從而大大改善匹配質量,提高系統的工作性能At first, the average - current controlled boost pfc and buck converter small - signal model are estabished. the average - current controlled boost pfc and buck converter prototype are designed and manufactured. on basis of the small - signal model, the two - stage i / o impedance characteristic and miller effect are analyzed by simulation with matlab software
其次單獨設計了前級、后級變換器樣機,在兩級模型基礎上,應用matlab軟體模擬分析了前後級變換器對接處的i o阻抗特性和密勒效應,運用奈奎斯特判據對兩級結構寬輸出電壓范圍的功率因數校正器的穩定性進行了分析設計。分享友人